Users Manual

ManualsBrandsREI ManualsElectronicsECVR-6700T AM/FM/DVD/MP3/BT

Table Of Contents

Equipment Set Up and Initial Testing

Description:

MCI J4500 coach ECVR-6700T System Testing

Effective Date:

9-9-19

Revision: A

1. Equipment Set Up and Initial Testing

1.1.1. Turn BUS ignition switch to the ON position.

1.1.2. Verify that the POWER indicator on the ECVR-6700T is Blue, and the radio loads with the REI logo

screen.

1.2. Vehicle Dimmer Check

After the Radio boots up, turn the HEADLIGHTS on and very that the LCD screen dims when turned on.

If it does NOT, confirm that the BRIGHTNESS MODE is set to AUTO in the SETUP MENU. From the

Home screen select Passengers “SETUP”

Summary of content (15 pages)

PAGE 1
Description: MCI J4500 coach ECVR-6700T System Testing Effective Date: 9-9-19 Revision: A 1.Equipment Set Up and Initial Testing 1.2. 1.1.1. Turn BUS ignition switch to the ON position. 1.1.2. Verify that the POWER indicator on the ECVR-6700T is Blue, and the radio loads with the REI logo screen. Vehicle Dimmer Check After the Radio boots up, turn the HEADLIGHTS on and very that the LCD screen dims when turned on.
PAGE 2
Verify that the mode is set to AUTO, select to change if not. 1.3. Camera Check 1.3.1. Select “CAMERA” from the HOME page and confirm that an exterior view of the bus is present on the screen. Tap the screen an select drivers “RADIO”. Start the bus and place it in REVERSE, the same image as previously should be displayed. Return the bus back to Neutral and Apply the Parking Brake. If the image is reversed, TAP the screen and return to the HOME page. Select the SETUP option.
PAGE 3
1.4. Hand Microphone Check 1.4.1. 1.5. Wireless Microphone Check (if installed) 1.5.1. 1.6. Key the Microphones located in the drivers area one at a time. MICROPHONES should display as MIC 1, & MIC 2. Adjust the Passengers volume while keyed and verify operation on each one. The audio should be relatively clear without exceptional alternator or engine noise at normal volume levels. Key the Wireless Microphone located in the rack. The wireless should display as MIC 3 depending on options installed.
PAGE 4
1.7. Passenger Subwoofer Check (if installed) 1.7.1. Verify operation of both SUBWOOFERS if installed. Press HOME to access the SETUP menu. Scroll down to access the SUBWOOFERS ON/OFF option and verify it is set to ON: Next press the Subwoofers LFP setting ( Low Pass Filter) of the menu and verify it is set to 80Hz, adjust if necessary: Finally slide the SUBWOOFERS GAIN level indicator to increase or decrease the level. 15 is the default level displayed. This will adjust the SUBWOOFER LEVEL.
PAGE 5
1.9.1. Insert a DVD disc into the disc slot. If disc doesn’t automatically begin playing, press VID button on the ECVR-6700T. Chapter and time information should be displayed on the ECVR-6700T. The video monitors shall ALL turn on, verify their operation. The video should be clean with no lines or bars floating through the picture. The audio should be relatively clear without exceptional alternator or engine noise at normal volume levels. Adjust the Passengers VOL/SEL knob to change the passenger volume.
PAGE 6
1.10.2. Insert an audio source into the 3.5mm input. Switch the ECVR-6700T into EMS A/V 3 mode. Verify audio buy using the PASSANGERVOL/SEL knob to adjust the volume level. If necessary, adjust the level of the AUX audio source also. 1.10.3. Remove the 3.5mm audio source and connect a valid HDMI audio/video source into the HDMI input. With the ECVR-6700T still in EMS mode select HDMI 2, verify the HD source is playing content. Check that all monitors are displaying HD video.
PAGE 7
1.11. Media Player Verification Test (if installed) 1.11.1. To verify operation of the MP-1200 Media player if VIDEO EVEN button is not present. First verify that the ECVR-6700T control head is in EMS, mode by pressing the “SWITCH” icon then the “HDMI 3” button. Select a media file for playback using the MP-1200 remote. Confirm video and audio playback on the passenger’s monitors. Adjust the Passengers Volume level if necessary.
PAGE 8
Access the” Look for devices” feature of the mobile device and begin searching. After searching, the radio should appear in the list of devices as “DRIVER”. Press to accept. If prompted for a pass key, enter the Pin Code as displayed in the above. The default code for the radio unit is 0000 but can be changed along with the device name. A prompt to pair should appear on the mobile device. Press to accept and continue the process. The Bluetooth® icon of the radio should appear on the screen.
PAGE 9
1.14. External DVD2 Check (if installed) 1.14.1. Power up the DVD2 player and insert a DVD disc. To verify operation of DVD2, return to the HOME screen and select the “DVD2” icon. Once the player powers up and loads the disc, the system status will change to NORMAL and the playback controls on the bottom of the screen will become active. \ 1.15. Driver Radio Check 1.15.1. Press RAD button on the “DRIVER’s” section of the ECVR-6700T.
PAGE 10
1.15.2. Radio sound shall be heard in the DRIVERS speakers section. SEEK/MANUAL tune buttons. Touch the tuner grid for quick frequency changes also. The audio should be relatively clear without exceptional alternator or engine noise at normal volume levels. 1.15.3. Adjust volume up and down using the DRIVER’s VOL/SEL knob. Display should read “Drivers” and the level adjusted will be indicated between 0-30. 1.16. Drivers AUX Check (if installed) 1.16.1. 1.17.
PAGE 11
Access the” Look for devices” feature of the mobile device and begin searching. After searching, the radio should appear in the list of devices as “DRIVER”. Press to accept. If prompted for a pass key, enter the Pin Code as displayed in the above. The default code for the radio unit is 0000 but can be changed along with the device name. A prompt to pair should appear on the mobile device. Press to accept and continue the process. The Bluetooth® icon of the radio should appear on the screen.
PAGE 12
Next press the numbers 3368 followed by the “Check” icon.
PAGE 13
To change any of the Bluetooth or radio options, select this: To change the relative audio gain of a source when using Audio sources with less than ideal signals, select this: Use the Home icon to EXIT, or select a SETUP option from the option on the bottom of the screen. 1.19. Amplifier Adjustments (if necessary) 1.19.1. In the event where the passenger audio is not loud enough or is too loud, the gain level can be adjusted either way to compensate.
PAGE 14
1.20. Firmware Conformation From the Home screen select Passengers “SETUP” Select the INFO icon to display the current firmware version info: 1.21. It is recommended that the above steps be followed 2 times, once with and once without the coach running.
PAGE 15
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.