REGULUS Stereo Wireless Headset MT3551 Instruction Manual
EN Index Introduction ................................................................................................ 2 Package Contents...................................................................................... 2 Connectors and Controls ........................................................................ 3 Headphones ................................................................................................ 3 Transmitter cradle (Back Panel) .............................................
Connectors and Controls Headphones 8. Headphones power indicator 9. Power source DC1/DC2 selection switch 10. Headphones On/Off button 11. Removable ear cushion pad with battery compartment Transmitter cradle (Back Panel) 12. 13. 14. 15. Power socket Transmitter cradle audio input socket “SCAN” synchronisation button On/Off button of the transmitter cradle 1. Increase the volume 2. Search for radio station/synchronize headphones with transmitter cradle 3. Reduce the volume 4. Mode selection switch 5.
EN Transmitter cradle (Front and Top) LED Indicators on the Headphones The headphones have two LED indicators: the power indicator (8) and the radio and RF reception indicator. The following table contains a description of their meaning depending on their colour and status: 16. Transmitter 17. Transmitter cradle send indicator (AUDIO) 18.
Transmitter cradle LED Indicators The transmitter cradle has two LED indicators: the power/ charging indicator (18) and the RF send indicator. The following table contains: LED indicator Status Description AUDIO (17) Blinking, orange Attempting to establish a connection with the headphones. On, orange The RF link to the headphones has been established. However, the transmitter cradle is not receiving an audio signal from an external audio source (e.g. your hi-fi equipment).
EN Charging the Battery of the Wireless Headphones Please charge the battery before using the product for the first time. A charging cycle takes approx. four hours. Connect the integrated mains adapter to the transmitter cradle and to a wall outlet. ■ Place the headphones onto the cradle as shown below. The chargingcontacts (16) of the transmitter cradle must touch the charging contacts of the headphones (7).
establish a connection with the headphones. Synchronizing the Headphones and Transmitter Cradle. Synchronizing the transmitter cradle and the headphones can take a while. Powering the Transmitter Cradle Off You may power the transmitter cradle off whenever it is not needed. When powered off, it will not transmit any RF signals but the headphones battery will still be charged. 1. Slide the On/Off switch (15) on the transmitter cradle to the “OFF” position.
EN If you have connected your headphones to an external audio source, you may also adjust the volume directly on the audio source (e.g. by using the remote control of your hi-fi equipment). However, please remember that many audio devices provide a constant signal level on their Cinch audio outputs, thus not allowing a volume adjustment when using this type of connection. The last tuned-in station will not be saved when changing the operating mode or after powering the headphones off.
Battery operation You may power both the transmitter cradle and the headphones usingrechargeable or conventional batteries (only base). Batteries are not included in the package. Remove the batteries when the device is not to be used for a long time. Respect the environment. Old batteries do not belong in thedomestic waste. They must be handed in to a collection point for waste batteries. Rechargeable AAA batteries cannot be recharged when inserted into the base.
EN 1. Remove any cable connections and turn the transmitter cradle upside down, holding it in your hand. 2. Open the battery compartment by sliding the lock of the compartment cover into the direction of the compartment. The cover can be opened and then removed. 3. Insert three AAA batteries into the battery compartment. Note the + and – icons on the batteries and inside the battery compartment. 4.
Sound is interrupted or noisy. ■ The rechargeable battery or the inserted batteries of the headphones are depleted. Recharge the internal battery or replace the batteries with new batteries of the same type. ■ You are outside the maximum range of the transmitter. Move closer to the transmitter cradle. 1 x stereo Audio-In 3.5 mm jack (headphones) 1 x stereo Audio-In 3.
EN 12
