Use and Care Manual

ManualsBrandsRegency ManualsFurnitureMagons 72 in. Ash Grey Storage Accent Cabinet Buffet

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822

IMPORTANT NOTICE:

● Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.

● Check to be sure that you have all parts and hardware.

● Remove all wrapping materials, including staples & packing straps before you start to assemble.

● Do not tighten all screws/bolts until completely assembled.

● Keep all hardware parts out of reach of children.

72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS

Organize your parts and hardware. You will need a Phillips head and at head screw driver and rubber mallet.

Hardware :

A: Mounting Bracket(8) • B: Inner Hinge(4) • C: Outer Hinge(4) D: Lock Lip(2) • E: Small Screw(4)

F: Cam Pins(20) • G: Medium Screws(56) • H: Shelf Pins(16) • I: Adjustable Glides(6) J: Large Screws(8)

K: Door Handles(4) • L: Keys(2)

Parts :

M: Back • N: Front support • O: Middle Support• P: Bottom • Q: Left Side • R: Right Side • S: Shelves (4)

T: Top • U: Right side Door(2) • V: Left side Door(2) • W: Center wall

Figure 1: To open Cam, point

arrow toward Cam Pin hole.

To lock Cam, turn clockwise.

Summary of content (4 pages)

PAGE 1
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS Organize your parts and hardware. You will need a Phillips head and flat head screw driver and rubber mallet.
PAGE 2
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS STEP 1 : Attach front support(N) to middle support(O) by inserting the dowel rod on the end of(O) into the middle of(N). N O STEP 2 : Connect dowel rods on Front support(N) and Middle support(O) to the bottom(P). P O STEP 3 : Insert 2 cam pins(F) into back(M) and connect(M) to bottom(P) by inserting and locking cams (Fig1). N Cam locks on(P) facing (N) STEP 4 : Insert 4 cam pins(F) into both left(Q) and right(R) side.
PAGE 3
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS STEP 7 : Place 2 cam pins(F) in bottom(P) and attach center wall(W) with banded edge facing out by inserting and locking cams (Fig1). STEP 6 : Screw in 6 adjustable glides(I) in the locations shown below with 4 medium screws(G) each. I I I I V I P F W I P F F STEP 8a : Screw 8 cam pins(F) into top(T). Use 2 small screws(E) each to attach locking lips(D). STEP 8b : Attach top by inserting and locking cams (Fig1).
PAGE 4
72” STORAGE CABINET • LSC7236 •VSC7236 INSTRUCTIONS STEP 10 : Mount the right side doors(U) to the sides(Q,R) with 2 medium screws(G) each hinge. Also mount the left side doors(V) to the center wall(W) in the same manner. G G STEP 10a : Use 2 Large screws(J) per handle(K) and attach (K) to doors(T,U) using the 2 pre drilled holes per door. J J K IMPORTANT NOTICE: ● Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.