Product Manual

ManualsBrandsReelcraft ManualsCord ReelsRetractable Cord Reel with 4 Outlets — 65ft.L, 12/3

Operating Instructions

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725

Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605

Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com

Retractable Industrial Extension Cord Reel

Model Numbers:

LG3065 123 9Q LG3075 143 9Q

Rev: 9/2018

CAUTION: Read all instructions and warnings before operating!

SAVE THESE INSTRUCTIONS! READ ALL INSTRUCTIONS!

1. DO NOT handle this fixture or try to plug it in when your

hands are wet or damp or when you are standing on a wet or

damp surface or in water.

2. This fixture MUST ALWAYS BE USED in accordance with

all electrical and safety codes and ordinances, including

the most recent National Electric Code (NEC) and with the

Occupational Safety and Health Act (OSHA) Volume 1 on

General Industry Standards and interpretations.

3. ALWAYS make certain that the power source conforms to the

requirements on the fixture.

4. ALWAYS disconnect the power before servicing or inspecting

the fixture for any reason.

5. This fixture is ONLY FOR USE ON 110-125V and is equipped

with an approved 3 conductor cord with a 3-prong, grounded

plug. TO REDUCE THE RISK OF ELECTRICAL SHOCK, it should

only be plugged into a properly grounded 3-prong outlet.

6. FIXTURE IS NOT WATERPROOF and is not intended for us

in showers, saunas or in potentially wet locations. ALWAYS

keep this fixture away from sinks, tubs, showers, etc. NEVER

attempt to pick up plugged-in power tools or appliances

should they fall into standing water. Fatal electrocution could

result!

7. This fixture comes equipped with a 3-prong grounded plug.

DO NOT remove the 3rd prong or otherwise try to modify the

plug. If it will not fit the outlet, have the proper outlet installed

by a qualified electrician. Improper connection of the ground-

ing conductor can result in a risk of electrical shock.

8. NEVER attempt to plug the fixture into a non-grounded outlet

or extension cord and ALWAYS be sure that the extension

cord is in good electrical condition.

9. This fixture is intended for use as a general indoor power

source. DO NOT use in potentially dangerous locations, such

as in flammable or explosive atmospheres.

10. Keep away from heating vents, radiators, or other sources of

heat.

11. KEEP OUT OF REACH OF CHILDREN.

INSTALLATION

All three screws with washers must be used when installing

mounting bracket. Eliminating one or more of the supplied hex

head screws may allow bracket to detach allowing reel to fall

causing damage to vehicles, injury or death.

Wall Mounting

1. Pick the approximate location for the reel with 2 1/2 ft of a

110-125V standard outlet.

2. Locate a stud to install the mounting bracket. The bracket will

be placed against the wall vertically, directly over the center of

the stud.

3. Using the bracket as a template, mark the (3) screw locations

with pencil. (Fig. 1)

4. Pre Drill (Pilot) the three screw holes with the use of at 1/4”

drill.The depth of the Pilot holes should be at least 2”.

5. Install the bracket with the (3) provided head wood screws

with washers using a 1/2” wrench or socket. Tighten all three

until snug. (Fig. 2)

ELECTRICAL RATING

Model

Cord

Length

Cord Type /

Gauge

Maximum outlet rating

LG3075 143 9Q 75 FT 14/3 SJTOW 125V, 10 AMP, 1250 Watts

LG3065 123 9Q 65 FT 12/3 SJTOW 125V, 15 AMP, 1875 Watts

WARNING: DO NOT OVERLOAD! Check the amperages

of the tools or appliances to be plugged into the outlets

of the extension cord reel. Listed below are the maximum

amperage ratings.

WARNING: To avoid serious injury or death from electrical

shock or fire.

3 1/4” 3 1/4”

Fig. 1

Bracket hole pattern

3 - #5/16” SCREWS

Bracket A

Fig. 2

Summary of content (6 pages)

PAGE 1
Operating Instructions Retractable Industrial Extension Cord Reel Model Numbers: LG3065 123 9Q LG3075 143 9Q CAUTION: Read all instructions and warnings before operating! SAVE THESE INSTRUCTIONS! READ ALL INSTRUCTIONS! WARNING: To avoid serious injury or death from electrical shock or fire. DO NOT handle this fixture or try to plug it in when your hands are wet or damp or when you are standing on a wet or damp surface or in water. 2.
PAGE 2
Retractable Industrial Extension Cord Reel 6. 7. The reel can now be installed into the bracket. The following installation instruction will allow smooth retraction: a. When the mounting height is less than 5 ft, the reel should be positioned so that the cord opening face upward (fig. 3). b. When the mounting height is more than 5 ft, the cord opening should face downward (Fig. 4). Slide the mounting pin (B) through bracket and reel. Slide the locking pin (C) through the Mounting Pin for security.
PAGE 3
Instructions D’Opération Carrete industrial con cordón de extensión retráctil Modelo Nº LG3065 123 9Q LG3075 143 9Q AVISO:¡ Lea todas las instrucciones y avisos antes de su uso! ¡GUARDE ESTAS INSTRUCCIONES! ¡LEA TODAS LAS INSTRUCCIONES! ADVERTENCIA: Para evitar lesión o muerte seria del choque eléctrico o encenderlos: NO maneje este accesorio ni intente enchufarlo cuando sus manos son mojadas o húmedas o cuando usted está estando parado en una superficie mojada o húmeda o en agua. 2.
PAGE 4
Carrete industrial con cordón de extensión retráctil 6. 7. El carrete ahora se puede instalar en el soporte. La siguiente instalación permite una retracción eficiente: a. Cuando la altura del montaje es inferior a 5 pies, el carrete debe colocarse de modo que la apertura del cable está posicionada hacia arriba (fig. 3). b. Cuando la altura del montaje es de más de cinco (5) pies, la apertura del cable debe estar posicionada hacia abajo (fig. 4).
PAGE 5
Instructions D’Opération Enrouleur de rallonge industriel Modèle n° LG3065 123 9Q LG3075 143 9Q ATTENTION : lire toutes les instructions et tous les avertissements avant de se servir de l’appareil ! CONSERVER CES INSTRUCTIONS ! LIRE TOUTES LES INSTRUCTIONS ! AVERTISSEMENT: pour éviter des blessures graves ou même la mort par suite d’un choc électrique ou d’un incendie : NE PAS manipuler ou essayer de brancher cet appareil si on a les mains mouillées ou humides ou si l’on se tient sur une surface mouillée
PAGE 6
Enrouleur de rallonge industriel 6. 7. L’enrouleur peut maintenant être posé dans l’étrier. Pour que l’enrouleur fonctionne en douceur, suivre les étapes suivantes : a. Si l’enrouleur est posé à moins de 1,5 m du sol, l’installer de manière que la sortie du fil soit vers le haut (fig. 3). b. Si l’enrouleur est posé à plus de 1,5 m du sol, l’installer de manière que la sortie du fil soit vers le bas (fig. 4).