RTL8852AE User’s Manual (Realtek RTL8852AE) 11ax RTL8852AE Combo module Module User’s Manual Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.
RTL8852AE User’s Manual CONTENT ENVIRONMENTAL .......................................................................................................................... 3 WARNING .......................................................................................................................................... 4 Federal Communication Commission Interference Statement ...................... 4 INDUSTRY CANADA STATEMENT ...................................................................................
RTL8852AE User’s Manual ENVIRONMENTAL Parameter Minimum Maximum Units -55 +125 °C Ambient Operating Temperature 0 70 °C Junction Temperature 0 125 °C Storage Temperature
RTL8852AE User’s Manual Warning Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RTL8852AE User’s Manual This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. The SAR test is according to KDB 616217 for test requirements.” The maximum output power is reduced by software to perform SAR evaluation as application. Radiation Exposure Statement: (Mobile) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
RTL8852AE User’s Manual 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.
RTL8852AE User’s Manual 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID:TX2-RTL8852AE”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.
RTL8852AE User’s Manual OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules.
RTL8852AE User’s Manual function is available. The SAR evaluation is according to KDB 616217, and the module approach distance restriction is 5 mm for notebook, 10 mm for tablet. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel.
RTL8852AE User’s Manual IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
RTL8852AE User’s Manual dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6317A-RTL8852AE ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
RTL8852AE User’s Manual Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment : (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis pour les disp
RTL8852AE User’s Manual Chain 0 LYNwave ALA110-222050-300011 Chain 1 LYNwave ALA110-222050-300011 1 Chain 0 PSA RFDPA171320EMLB301 Chain 1 PSA RFDPA171320EMLB301 2 (dBi) (GHz) 3.5 2.4~2.5 5 5.15~5.85 3.5 2.4~2.5 5 5.15~5.85 3.14 2.4~2.5 5 5.15~5.85 3.14 2.4~2.5 5 5.15~5.85 PIFA i-pex(MHF) PIFA i-pex(MHF) Dipole i-pex(MHF) Dipole i-pex(MHF) For SAR (Portable) Antenna Frequency Brand Model REALTEK Antenna Connector Type Type 2.4~2.5 PIFA i-pex(MHF) 5.15~5.
RTL8852AE User’s Manual 2. 系統廠商應於平台上標示「本產品內含射頻模組: XXXyyyLPDzzzz-x」字樣。 Japan Statement Host system must be labeled with "Contains MIC ID:xxxxxx“, MIC ID displayed on label. Installing the Wireless PCIe NGFF2230 module Hardware Installing PCIe NGFF2230 module to PCIe NGFF2230 connector and connect two external Wi-Fi antennas on I-PEX connectors.
RTL8852AE User’s Manual Un-installing the Wireless PCIe NGFF2230 module Hardware Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF2230 module board and remove the Wireless PCIe NGFF2230 module board from PCIe NGFF2230 connector port
RTL8852AE User’s Manual Installing the WLAN PCIe & Bluetooth USB NGFF2230 module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first. A. Execute the “setup.
RTL8852AE User’s Manual B. Select ”I accept the terms in license agreement” and click “Next” to process the installation C. Click “Next” button.
RTL8852AE User’s Manual D. Select “Complete” and click “Next” button.
RTL8852AE User’s Manual E. Click “Install” button. F. Click “Finish” button.
RTL8852AE User’s Manual G. Please click “Next”to continue. H. Please click “Next”to continue.
RTL8852AE User’s Manual I. Please click “Install”to start installation. J. Please click “finish”to finish the installation.
Un-installing the Wireless PCIe NGFF2230 module Software A. Uninstall the RTL8852AE WLAN Driver from “Start”→ “Control Panel”→ “Programs” Please select items as below and click “Uninstall” to remove RTL8852AE WLAN, BT driver and MP UI.