RTL8822C User’s Manual (Realtek RTL8822C) Combo NGFF Type1216 Module User’s Manual Preliminary Version 2020/01/14 Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.
RTL8822C User’s Manual CONTENT ENVIRONMENTAL .......................................................................................................................... 3 OPERATING ............................................................................................................................................ 3 STORAGE................................................................................................................................................ 3 MTBF CACULATION ..................
RTL8822C User’s Manual ENVIRONMENTAL Operating Operating Temperature: 0°C to +70 °C Relative Humidity: 5-90% (non-condensing) Storage Temperature: -40°C to +80°C (non-operating) Relevant Humidity: 5-95% (non-condensing) MTBF caculation Over 150,000hours
RTL8822C User’s Manual Warning Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RTL8822C User’s Manual The SAR test is according to KDB 616217 for test requirements.” The maximum output power is reduced by software to perform SAR evaluation as application. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement: (Portable) The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual.
RTL8822C User’s Manual Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.
RTL8822C User’s Manual 5 5.15~5.85 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: TX2-RTL8822C”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.
RTL8822C User’s Manual OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules.
RTL8822C User’s Manual possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. L'évaluation SAR est conforme à KDB 616217, et la restriction de distance d'approche du module est de 5 mm pour le portable, 10 mm pour la tablette. Radiation Exposure Statement: (Mobile) This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
RTL8822C User’s Manual IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
RTL8822C User’s Manual dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6317A-RTL8822C ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
RTL8822C User’s Manual Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment : (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis pour les dispo
RTL8822C User’s Manual Chain 0 LYNwave ALA110-222050-300011 Chain 1 LYNwave ALA110-222050-300011 1 Chain 0 PSA RFDPA171320EMLB301 Chain 1 PSA RFDPA171320EMLB301 2 (dBi) (GHz) 3.5 2.4~2.5 5 5.15~5.85 3.5 2.4~2.5 5 5.15~5.85 3.14 2.4~2.5 5 5.15~5.85 3.14 2.4~2.5 5 5.15~5.85 PIFA i-pex(MHF) PIFA i-pex(MHF) Dipole i-pex(MHF) Dipole i-pex(MHF) For SAR (Portable) Antenna Frequency Brand REALTEK Model Antenna Connector Type Type 2.4~2.5 PIFA i-pex(MHF) 5.15~5.
RTL8822C User’s Manual 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波 輻射性電機設備之干擾。 1. 使用此產品時應避免影響附近雷達系統之操作。 2. 高增益指向性天線只得應用於固定式點對點系統。 模組認證： 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤。 2. 系統廠商應於平台上標示「本產品內含射頻模組： XXXyyyLPDzzzz-x」字樣。 Japan Statement Host system must be labeled with "Contains MIC ID:xxxxxx“, MIC ID displayed on label.
RTL8822C User’s Manual Installing the Wireless PCIe NGFF1216 module Hardware Installing PCIe NGFF1216 module on NGFF2230 load board to PCIe NGFF2230 connector and connect two external Wi-Fi antennas on I-PEX connectors.
RTL8822C User’s Manual Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF1216 module on NGFF2230 load board and remove the Wireless PCIe NGFF1216 module on NGFF2230 board from PCIe NGFF2230 connector port Installing the Wireless PCIe NGFF1216 module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7.
RTL8822C User’s Manual A. Execute the “setup.exe”, Click “Next” to process the installation B. Click “Install” to process the installation C.
RTL8822C User’s Manual D. After step “C” please press Next button. E. Please click “YES” to install BT package. F. Please click “下一步”to continue.
RTL8822C User’s Manual G. Please click “下一步”to continue.
RTL8822C User’s Manual H. Please click “安装”to start installation. I. Please click “完成”to finish the installation.
RTL8822C User’s Manual J.
Un-installing the Wireless PCIe NGFF1216 module Software A. Uninstall the RTL8822C WLAN Driver from “Start”→ “All Programs”→ “REALTEK 11ac 8822CE PCIE WLAN NIC Massproduction kit” Please click “Uninstall” to remove RTL8822C WLAN driver.
RTL8822C User’s Manual Installing the Bluetooth USB Module Software A. Insert the NGFF1 card into system connector. B. Boot on system then the “Geniric Bluttooth Adapter” device will show up in device manager. C. Click right button on “RT Bluetooth Radio” and select “Update Driver”.
RTL8822C User’s Manual D. After select “Update Driver Software ” then the Hardware Update Wizard will pop up, please select “Browse my computer for driver software” and press Next button. E. After step “D” please Select “Let me pick from a list of device drivers on my computer ”.
RTL8822C User’s Manual F. Finish step “E” then select “Have Disk..” G. Now select browse to find the driver for device and press Next button.
RTL8822C User’s Manual Page 26/27
RTL8822C User’s Manual H. Then click “Install this driver software anyway” to continue. I. Press close button to complete the install process and you can see the Driver will be show up in Device Manager.
v RTL8822CE SINGLE-CHIP 802.11ac/a/b/g/n 2T2R WLAN AND INTEGRATED BLUETOOTH 5 CONTROLLER WITH PCI EXPRESS /USB2.0 MIXED INTERFACE DATASHEET (CONFIDENTIAL: Development Partners Only) Rev. 0.1 27, Aug., 2018 Track ID: Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.
RTL8822CE Datasheet 1. General Description The Realtek RTL8822CE is a highly integrated single-chip that support 2-stream 802.11ac solutions with Multi-user MIMO (Multiple-Input , Multiple-Output) with Wireless LAN (WLAN) PCI Express network interface controller with integrated Bluetooth 5 USB interface controller. It combines a WLAN MAC, a 2T2R capable WLAN baseband, and RF in single chip. The RTL8822CE-CG provides a complete solution for a high-performance integrated wireless and Bluetooth device.
RTL8822CE Datasheet The RTL8822CE MAC supports 802.11e for multimedia applications, 802.11i and WAPI (Wireless Authentication Privacy Infrastructure) for security, and 802.11n/802.11ac for enhanced MAC protocol efficiency. Using packet aggregation techniques such as A-MPDU with BA and A-MSDU, protocol efficiency is significantly improved.
RTL8822CE Datasheet 2. Features General 76-pin QFN CMOS MAC, Baseband PHY and RF in a single chip for IEEE 802.11a/b/g/n/ac compatible WLAN Support 802.11ac 2x2,Wave-2 compliant with MU-MIMO Complete 802.11n MIMO solution for 2.4GHz and 5Ghz band Maximum PHY data rate up to 173.3 Mbps using 20MHz bandwidth, 400Mbps using 40MHz bandwidth, and 866.7Mbps using 80MHz bandwidth. Backward compatible with 802.11a/b/g devices while operating at 802.
RTL8822CE Datasheet MAC Features Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU) Low latency immediate Block Acknowledgement (BA) Long NAV for media reservation with CF-End for NAV release PHY-level spoofing to enhance legacy compatibility Channel management and co-existence Multiple BSSID feature allows the RTL8822CE to assume multiple MAC identities when used as a wireless bridge Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting for higher mu
RTL8822CE Datasheet 3. Application Diagrams 3.1. 11ac Dual-Band 2x2 RF Application 40MHz 3. 3 V SPS / LDO Regulators Crystal NV Memory BT LE HCI Controller RFIO_BT SW BT TRSW SW Transceiver Modem BT BB Controller BT RAM MCU Ext PCIe + USB Interface RFI_WL2G_S1 ADC RFIO_WL2G_S1 /BT PCIe & USB Host PTA RX I/ Q TRSW SW RFI_WL5G_S1 Control and DA C TX I/ Q RFIO_WL5G_S1 TRSW RFI_WL2G_S0 WLAN Configuration WLAN MCU 2.
RTL8822CE Datasheet 45 44 GND_SPS LDO_V13_PHY_I 46 LX_SPS_V13_O REFCLK_N 47 LX_SPS_V13_O REFCLK_P 49 48 43 42 41 40 39 VD33SPS VD10_VDDTX 50 VD33_IO HSON 51 VD10D_WLBB_TOP HSOP 53 52 RREF GND_TX 57 56 55 54 HSIN HSIP VD10_USB HSDP Pin Assignments HSDM 4.
RTL8822CE Datasheet 4.1. Package Identification & Mark Information Green package is indicated by a ‘G’ in the location marked ‘V’ in Figure2The version is shown in the location marked ‘V’. Pin Descriptions 5. The following signal type codes are used in the tables: I: Input O: T/S: Tri-State bi-directional input/output pin O/D: Open Drain N/A: No Bonding pin S/T/S: P: Output Sustained Tri-State Power pin 5.1. Power On Trap Pin Symbol TEST_MODE_SEL Type I Table 1.
RTL8822CE Datasheet Symbol REFCLK_N/REFCL K_P CLKREQ# Type I Pin No Description 47,48 PCI Express Differential Reference Clock Source: 100MHz ± 300ppm Voltage I/O/D 33 Reference Clock Request Signal.Also used by L1 PM substates. This signal is used by the RTL8822CE to request for the PCI Express reference clock. 3.3V WAKE# O/D 32 Power Management Event: Open drain, active low. Used to reactivate the PCI Express slot’s main power rails and reference clocks.
RTL8822CE Datasheet Symbol RFI_WL5G_S0 Type I Pin No 18 Description WLAN 5G RF input for path S0 in external LNA/FEM configuration 5.5. LED Interface Symbol BT_LED WL_LED Type O O Pin No 65 66 Table 5. LED Interface Description BT LED Pin (Active Low) WL LED Pin (Active Low), shared with GPIO8 5.6. Power Management Handshake Interface Symbol WL_DIS# Table 6. Power Management Handshake Interface Type Pin No Description I 27 Shared with GPIO9.
RTL8822CE Datasheet Symbol GPIO8 GPIO9 GPIO11 GPIO12 GPIO13 GPIO14 Type IO IO IO IO IO IO Pin No 66 27 63 29 61 62 Description General Purpose Input/Output Pin General Purpose Input/Output Pin General Purpose Input/Output Pin General Purpose Input/Output Pin General Purpose Input/Output Pin General Purpose Input/Output Pin 5.8. HCI Power Pins Symbol LDO_V13_PHY_I GND_TX RREF VD10_VDDTX VD33_USB VD10_USB GND_USB Type P P P P/I P P P Pin No 46 52 45 49 59 55 58 Table 8.
RTL8822CE Datasheet Symbol GND_SPS Type P Pin No 39 Description Switching Regulator Ground 5.11. RF Power Pins Symbol VD13_BT VD33_BT VD33_LDO_WL VD13_TRX_S1 VD33_TX2G_S1 VD33_TX5G_S1 VD33_PAD_S1 VD33_TX2G_S0 VD33_PAD_S0 VD33_TX5G_S0 VD13_TRX_S0 VD13_SYN VD33_SYN VD33X VD13_AFE Type P P P P P P P P P P P P P P P Pin No 74 75 1 2 5 8 10 13 15 16 19 20 21 24 25 Table 11. RF Power Pins Description VDD 1.3V for BT RF VDD 3.3V for BT RF VDD 3.3V for internal LDO input VDD 1.3V for S1 WLAN RF VDD 3.
RTL8822CE Datasheet 6. Electrical and Thermal Characteristics 6.1. Temperature Limit Ratings Parameter Storage Temperature Ambient Operating Temperature Junction Temperature Table 12. Temperature Limit Ratings Minimum Maximum -55 +125 0 70 0 125 Units C C C 6.2. DC Characteristics 6.2.1. Power Supply Characteristics Symbol VD33 VD10 Table 13. DC Characteristics Parameter Minimum Typical 3.3V I/O Supply Voltage 3.0 3.3 1.05V Core Supply Voltage 0.945 1.05 Maximum 3.6 1.
RTL8822CE Datasheet 7. Interface Timing Specification 7.1. PCIe Bus during Power On Sequence Ton 3.3V CLKREQ# TPVPGL PERST# TPERST#-CLK REFCLK WL_DIS# BT_DIS# Tattach SE0 Reset USB D+ Card Detection Tk-state USB D- Figure 3.
RTL8822CE Datasheet 7.2. PCIe PERST# Timing Sequence 3.3V 3.3V (Power) 0V TPERST#_LOW TPERST#_LOW High PERST# Low TPERST#_HIGH Table 17. RTL8822CE-CG PCIE PERST# Timing Parameters TPERST#_LOW TPERST#_HIGH 7.3. Min 6 400 Typical 10 500 Max X X Unit ms ms Description PERST# low duration PERST# high duration Power Off Sequence TOFF TON 3.3V 3.3V (Power) 0V 0V TOFF-TIME Figure 4. RTL8822CE-CG Power Off Sequence Table 18.
RTL8822CE Datasheet 7.4. Platform state transitions 3.3V Power range +/-0.165V 3.3V Ripple 3.3V Noise 300mVpp @ switching frequency > 400KHz Single-Chip 802.11 ac/a/b/g/n 2T2R WLAN Controller with PCI-E Interface 17 Rise time Min Max 1ms 5ms Track ID: Rev. 0.
RTL8822CE Datasheet 8. Mechanical Dimensions Symbol A A1 A3 b D/E D2 E2 e L Min 0.80 0.00 0.15 8.90 6.10 4.78 0.30 Dimension in mm Nom 0.85 0.02 0.2 REF 0.20 9.00 6.20 4.88 0.40 BSC 0.40 Max 0.90 0.05 Min 0.031 0.000 0.25 9.10 6.30 4.98 0.006 0.350 0.240 0.188 0.50 0.012 Dimension in inch Nom 0.033 0.001 0.008 REF 0.008 0.354 0.244 0.192 0.016 BSC 0.016 Max 0.035 0.002 0.010 0.358 0.248 0.196 0.020 Notes： 1. CONTROLLING DIMENSION：MILLIMETER(mm). 2. REFERENCE DOCUMENTL：JEDEC MO-220.
