Realtek Ameba1 DEV01 User Manual This document define pin out of Ameba DEV. Version 1.
Document Number: UM0058 _______________________________________________________________ Table of Contents 1 Hardware block diagram ......................................................................................................... 3 2 System requirements .............................................................................................................. 4 3 Pin out reference.................................................................................................................
Document Number: UM0058 _______________________________________________________________ 1 Hardware block diagram IC: RTL8195AM DEV HDK version: RTL-AMEBA_DEV01_1v1 NFC Antenna Wi-Fi external ANT connector Wi-Fi PCB Antenna Ameba reset button J-TAG UART RTL8711AF J22 J21 DAP DAP+DC +serial port USB Host DC 5V J19 J20 DAP update Mode button March 8, 2016 DAP reset button 3
Document Number: UM0058 _______________________________________________________________ 2 System requirements Windows PC (XP, Vista, 7) USB type A to Micro-B USB cable x 1 RS-232 to UART board(debug) x 1, JTAG cable x1 (option) 3 Pin out reference 3.
Document Number: UM0058 _______________________________________________________________ 3.
Document Number: UM0058 _______________________________________________________________ 46 47 39 37 36 38 40 41 42 43 12 11 10 9 8 7 6 5 4 3 2 1 J21 D15 D14 I2C_SCL I2C_SDA AREF GND D13/SCK/PWM1 D12/MISO/PWM3 D11/MOSI/PWM2 D10/CS/PWM0 D9/PWM1* D8/PWM0* GPIOA_2 GPIOA_3 GPIOA_4 GPIOD_5 GPIOD_4 GPIOA_5 GPIOA_7 GPIOA_6 26 25 24 3 4 23 22 21 8 7 6 5 4 3 2 1 J19 D7 D6 D5 D4/PWM1* D3/PWM2* D2 TX/D1 RX/D0 Module Pin Num Header Pin Num GPIOB_2 GPIOB_3 GPIOC_5 GPIOC_4 VDD33 GROUND GPIOC_1 GPIOC_3 GPIOC_2 GPIOC
Document Number: UM0058 _______________________________________________________________ 4 Antenna hardware setup R206 I-PEX/U.FL connector: R206 External antenna: R207 PCB antenna: R208 R207 R208 5 Peripherals support Debug UART: GPIOB_[0..
Document Number: UM0058 _______________________________________________________________ JTAG: GPIOE_[0..4] 5.1 Pin function table setup Multiple functions are supported by group setup. For example: GPIOA_6(Rx), GPIOA_7(Tx), GPIOA_3(RTS) and GPIOA_5(CTS) are used if UART0 function. GPIOA_3(RTS) and GPIOA_5(CTS) can not be used as other functions. For example: GPIOC_0, GPIOC_1, GPIOC_2, GPIOC_2, GPIOC_3 are used if PWM is occupied. GPIOC_1(PWM1) and GPIOC_2(PWM2) can not be used as other functions.
Document Number: UM0058 _______________________________________________________________ 6.2 J-Link/JTAG Weld JTAG and log UART connectors to HDK board and connect with pitch 2.54mm 2x5pins connector. It is recommended to weld the connector on the bottom side. Users can connect extension boards from top side.
Document Number: UM0058 _______________________________________________________________ JTAG 5V DC UART Dupont Line or 2.54mm 2x5 pins connector. Power On(Disable DAP mode) Holding TGT_NRESET button (J24, red-circled) then press Pdn button (J13, blurcircled). Release the button after power on.
Document Number: UM0058 _______________________________________________________________ J24 J17 J13 6.3 DAP mode In DAP mode, the DAP firmware can be updated. Holding TGT_NRESET button (J24, red-circled) then press nRESET button (J17, blur-circled). Then the DAP mode window will show up.
Document Number: UM0058 _______________________________________________________________ J24 J17 J13 DAP window will show up when entering DAP mode.
Document Number: UM0058 _______________________________________________________________ 7 Ameba1 DEV01 pin out March 8, 2016 13
Document Number: UM0058 _______________________________________________________________ 8 Sensor board Extension board: RTL-AMEBA_EXT B2_2V0 March 8, 2016 14
Document Number: UM0058 _______________________________________________________________ 9 Warning 10.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Document Number: UM0058 _______________________________________________________________ IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 13.
Document Number: UM0058 _______________________________________________________________ may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: TX2-RTL8195AM ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.
Document Number: UM0058 _______________________________________________________________ To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated.
Document Number: UM0058 _______________________________________________________________ French translation: Pour les produits disponibles aux Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures.
Document Number: UM0058 _______________________________________________________________ d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. The following antenna type and max. gain be used and approved for the module: 1) 2) 3) 4) Dipole antenna, max. gain: 3dBi PIFA antenna, max. gain: 3.5dBi Printed antenna, max. gain: 2dBi PIFA antenna, max. gain:2.89dBi 10.
