DIGITAL WIRELESS 7” LCD MONITORING SYSTEM WITH SD CARD RECORDING MODEL:CM642702
Feature list: 850nm IR Led visible distance up to 10m 7” TFT Lcd Digital panel (800 RGB x 480) Two way audio Scan function PIR trigger or Video motion detect recording Manual recording Schedule recording separate settings from Monday to Sunday SD Card capacity up to 64GB One Lcd monitor can pair four cameras Frame rate: Cam x 2 : 720p x1 @ 15 fps or Cam x 2 : VGA x2 @ 30 fps or Cam x 4 : or VGA x 4 @ 15 fps Individual recording files 5 Seconds pre-recording
Wireless Receiver Front Controls 1. Cam--- Press the button to view cameras in automatic switching mode. 2. Quad---- Press Quad button to view the images in quad mode. Press Quad buttons to exit from quad mode to automatic switching mode 3. Scan--- Press the button to switch the receiver to scan mode. When there’s motion detected by cameras, the LCD will lighten up and show the live video from the camera. 4.
Side Controls 13. SD card slot---- Insert SD card to this SD card slot for both video and audio recording. 14. Service--- Used for service purposes only. 15. Talk----Press this button to talk back to the camera and the icon is displayed on the screen. Back Controls 16. Ethernet Port (RJ45)--- Connect the receiver to your router using the included Ethernet cable to enable smartphone / tablet connectivity. 17. DC 5V Power Input –-- Connect the included DC 5V/2A power adaptor to power the receiver. 18.
Wireless Receiver Installation 1. Before receiver installation, choose one installation method from below 2 methods: 1). Desktop or table stand. For this method, you only need to place the receiver on a desktop. 2). Wall mounting Decide where to mount the receiver first. Make sure the range between the position and the nearest power output port is no more than 5 feet. Also, the range between the position and TV or VCR/DVR should be no more than 5 feet.
Wireless Camera 1. Camera Antenna –Receives & Sends signals to or from the Receiver. 2. Lens – Catches the video in front of the lens and transmits video from camera to receiver. 3. IR LED –Infrared LEDs provide viewing in no/low light conditions. 4. PIR sensor–Detects motion in front of the lens and emits detection signal to transmitter. 5. Thumbscrew-Rotates the thumbscrew to adjust the angle of the camera until the desired view is set 6. Speaker-Produces the sound transmitted from the monitor. 7.
Night Vision This camera has built-in IR LEDs, which provides the camera with the ability to view images in no/low light conditions. It is important to use the provided power adaptor when using the camera for prolonged periods in low light conditions, as the built-in IR LEDs will drain power more quickly than regular daytime use. Night vision will be automatically switched on in low illumination condition. 1. Carefully unpack the Camera.
1 Using the system By default, the camera(s) included with your system are automatically paired to the receiver. The camera(s) and receiver will communicate with each other once they are powered on. Note: It is recommended to power on the cameras before powering on the receiver. 1.1 Understanding the On-screen Display With camera 1 properly connected and powered on, the system displays a full-screen live view of the camera.
1 Signal Indicator –The signal indicator shows the strength of the signal being received from the camera. The number of bars in the Signal Indicator shows the strength of the signal. One, or no bars indicates the signal is poor, and 4 bars indicate a very strong signal. Note • If the signal is low (e.g.,1 or 2 bars) adjust the antennas, or reposition the cameras or receiver for best performance. • The signal indicator is not shown during Quad mode.
4 Network status Indicator –A red icon not connected to a network.A green icon shows that the connection has failed or the system is shows that the system is connected to the Internet and tell you the monitor connect with internet mode. A yellow icon shows that the system is connected to the intranet and tell you the monitor connect with intranet mode.
2 Viewing Modes There are four different viewing modes available on the system: single channel viewing, Auto Sequence Viewing mode (view individual channels automatically in sequence), Quad mode, and Scan mode. Note: Auto Sequence Viewing mode cycles through connected channels in full-screen. Use Quad mode to view up to four cameras simultaneously. Use Scan mode, the receiver’s LCD screen and speaker will turn off unless motion is detected by one of the cameras.
3.1 Motion Recording System only records when motion is detected by a camera(s).Press Motion on the top of the receiver to start motion recording. There is a on the bottom right of corner. In this mode the receiver starts recording prior to 5 seconds when motion detected by any activated camera. The recording time can be set to 15s,30s or 1minitus after last detection.
4. Once you have selected the month and the channels to display on the calendar, press OK to refresh the display. Dates that have recordings available for playback are highlighted in green. 5. Move the joystick left / right arrow to select a date on the calendar, and press OK to view a list of recordings for that date. Note: • The system uses a 24-hour clock.
6. Browse to the file you would like to delete. Press the joystick UP/DOWN arrow to select the file which you want to delete then press Delete . 7. A confirmation message appears as below. Select YES and press OK to delete the file. 8. Repeat the steps above for other files on the SD card. CAUTION:Do NOT delete folders on the SD card using your computer. Deleting folders may affect your access to other files on the card or may affect normal operation of the SD card with the system.
5 Accessing Menu System Use Menu on the receiver to access to Menu system. Use the joystick to navigate up/down/left/right in the menu, and push the joystick OK to confirm a setting or selection. The Main Menu contains 5 submenus: 1.Settings –Use the menu for system settings, such as date & time ,default setting, format memory, time zone, network and firmware update. 2. Detect–Use the menu to set Camera’s motion detect sensitivity(Hight,Medium,Low,Off) 3.
- Default Settings: Restore the system to default settings(Default No). Select Yes and then press OK to confirm. The system takes a few moments to restore default settings. Also you can see the firmware version V0.18-140128, when you update the firmware, you can see here to confirm whether you have done well. NOTE: Restoring default settings does not affect files recorded to the memory card or reset the date and time on the system. - Format Memory: Select Yes to format the SD card.
A:To update firmware from server 1. Connect the included Ethernet cable from the Ethernet port on the receiver to your router. The new download icon ( ) appears on the screen if new firmware is available. 2. Press Menu, then press the joystick to select Settings. 3. Select Firmware Upgrade. 4. Select From Server, then select Yes. The system takes a few moments to install the latest firmware. 5. After upgrading the new firmware, the monitor will automatically reboot .
2.Information:Set up the Static IP address and Dynamic IP on/off, display the current network information(IP State,IP Address, default gateway, MAC address ,UID as pasted on the back of monitor ,etc). 3.Reset password: Reset the password of remote access by 000000 5.2 Detect Separately to Set each Camera’s motion detect sensitivity (High, Medium, Low, Off), Press the joystick up/down arrow to select then Press OK to confirm the adjustment.(Default Low) 5.
5.4 Record Use the Record menu to change Duration(motion recording time), set a recording schedule, and enable/disable overwrite. You can set up the recording parameters in record menu. Note: To use the recording function, make sure a SD card is inserted into the SD card slot. - Duration: The recording time when there is motion detected by a camera in automatic recording mode. The recording time can be set to 15s ,30s or 1 minute.
Stopping Scheduled Recording When the stop time arrives, the system stops recording automatically. If necessary, you can stop schedule recording manually. To stop schedule recording: Press Rec to stop schedule recording. Modifying or Deleting a Recording Schedule You can modify any recording schedule by adding or subtracting recording time. To modify /delete a recording schedule: 1. Press Menu , then select Record. Press OK to confirm. 2. Select Schedule Recording. 3.
NOTE: It is highly recommended to pair the cameras to the receiver before permanently mounting the cameras. The pairing function assigns each camera to a different channel on the wireless receiver (up to 4 cameras), and is necessary for configuring additional cameras. NOTE: It is highly recommended to pair the cameras to the receiver before permanently mounting the cameras. 1. Power on the receiver by connecting it to power outlet with supplied 5V power adaptor. 2.
-Brightness: Press right arrow to increase the brightness level for the selected camera,or left arrow to decrease brightness. Camera brightness is measured on a scale of 1-6 where 1 is the darkest and 6 is the brightest. Press OK to save changes.
Android and iOS App Remote view 1. Download app MyCam View 1.0.0.apk freely from the App Store or the Google player store on your smart phone or tablet.(Make sure your phone connect with network) 2. Connect the 7’’monitor with your home router by internet cable. 3. Add camera(Android APP for example) Touch the App icon MyCam View to launch the app, Tap “Click here to add camera” Then the right pictures as showed, there are 2 options to get the UID from the monitor.
Then press OK to confirm it. 4. The system will show in your device list at an online status as below picture. 5. Press the camera you have added on your device, now you can view live video from your camera in either portrait or landscape mode.
View icon Snapshot Icon Mute Icon : press this icon to view Snapshot photos already taken. : press this icon to take photo from camera side : It cut off the audio on the camera side. Press this icon to listen the audio from camera side. Talk back Icon CH Icon :Press it to talk back to the camera currently being displayed on your phone. : press this icon to change channel which you want to see.
Online:1,only one remote visit, system support 4 remote visit at the same time. Quality: shows the network quality. 6. Back to the add camera menu, then press the down arrow,a new interface pops out as showed .
Reconnect: If your remote device connected failed with the camera, press it to reconnect. Edit Device: Device setting and Advanced setting are under this menu. You can see the camera’s details under Device Setting. You can modify Password setting(default 000000) , video Quality(default Min) and Alert interval(default 3 MIN)under Advance setting. View Event: Select it to playback the video on your phone.
View Snapshot: Select it to view the photos you have taken by Snapshot key. Remove Device: Delete this camera from your phone FCC and IC Note: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AND INDUSTRY CANADA LICENSE-EXEMPT RSS STANDARD(S). OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
