User's Manual

ManualsBrandsRDI Technology ManualsCamera & PhotoDIGITAL WIRELESS CAMERA AND RECEIVER SYSTEM

QRZ



\RX



FDQ



VHH

1. Power: Pressing this button turns the monitor on and o

2. TV/AV: If your monitor is connected to another video source, pressing this button will

transfer the image from the 7" LCD monitor to the attached monitor.

3. Quad: Opens up a quad screen view. For more information on camera viewing, please

see “Camera Viewing” on Pg. 16

4. Volume: This adjusts the volume of the audio that plays through your monitor

5. IR Sensor: The IR sensor is how the remote and monitor communicate

6. Manual Record: Prompts the monitor to begin constant recording. To stop recording, press this

button again

7. Motion Record: Prompts the monitor to record only when motion is detected. To stop motion

recording, press this button again

8. Manual Channel: Manually changes which camera is being viewed on screen

9. Auto Channel: Turns auto channel on and o. When this function is on, the camera channels will

sequence through automatically

10. Delete/Scan: This button will turn on the screen saver. The screen saver will display until

motion is detected, once detected, the screen saver will close and the monitor

will display the camera that detected motion. During playback this button allows

you to delete single clips of recorded footage. For more information on deleting

recorded footage, please see “DELETE” on Pg. 27

11. Menu/Exit: Enters and exits the main menu

12. Joystick: This tab has many functions when accessing the menu as well as playing back

footage. For information about how to use this joystick, please see “Joystick” on

Pg. 14 of the manual

13. Antenna: This antenna allows for a stronger signal between the camera and monitor

14. Power Input: Plug the small end of the included power adapter marked “monitor” into this area

15. A/V Out: Plug the single end of the included A/V cable into this area

16. SD Card Insert: Your SD card can be inserted into this area to record and save footage

17. Talk: This button allows for two-way communication. The monitor and camera are

both equipped with a microphone and a speaker, pressing this button allows you

to speak through the camera from the monitor

MONITOR

Summary of content (9 pages)

PAGE 1
QRZ \RX FDQ VHH MONITOR 1. Power: Pressing this button turns the monitor on and off 2. TV/AV: If your monitor is connected to another video source, pressing this button will transfer the image from the 7" LCD monitor to the attached monitor. 3. Quad: Opens up a quad screen view. For more information on camera viewing, please see “Camera Viewing” on Pg. 16 4. Volume: This adjusts the volume of the audio that plays through your monitor 5.
PAGE 2
Q Z \ Q HH REMOTE The included remote control has the same functions as the monitor with the exception of two commands that are NOT included on the remote control, they are: • Talk: Cannot access talk function with remote • Power: Cannot power on or off the monitor from the remote control CAMERA 1. Pair Button: Located at the back of the camera, you press this Back of Camera button when pairing the camera and monitor. For more information, please see “Pairing” on Pg 14 2.
PAGE 3
THINGS TO CONSIDER BEFORE INSTALLATION • • • • • • • • The camera should be installed between 8 to 13ft above the area to be monitored Ensure that the camera is installed NO MORE than 100 ft away from the monitor’s position to maintain a strong signal between the camera and monitor Before mounting the camera, ensure there are no obstructions in the camera’s view Place camera in the most strategic place where it can provide detailed video of your home or business.
PAGE 4
MOUNTING THE CAMERA 1. Decide if the camera will be wall-mounted or sitting on a desk/tabletop. The camera can be adjusted for many mounting scenarios by rotating it to the required position. • Keep in mind that the camera is microphone equipped.
PAGE 5
\ PLUGGING IN MONITOR Once the monitor is connected to a power source , turn it on using the power button and it will automatically pair with the camera. If the camera and monitor do not automatically pair please see “PAIRING” Pg 14. To plug monitor in: 1. Make sure that the monitor is set up no more then 100ft from the camera. This is to ensure a strong signal between the camera and monitor. 2. Plug the monitor’s power adapter (marked for monitor) into the monitor’s power input area (marked “9V DC”). 3.
PAGE 6
My Unit has Scrolling horizontal lines • Ensure that the device is set to NTSC. For more information please see “AV OUT on Pg. 22 Schedule record is not working • Ensure that both manual and motion record modes are turned OFF for schedule record to take place SPECIFICATIONS CAMERA Image sensor.............................................................................................................1/4" CMOS Color Outdoor use ...............................
PAGE 7
\ MONITOR Wireless Frequency ...................................................................................................2400~2483.5Mhz Channel Frequencies .................................................................................................Hopping Frequency Number of Cameras Supported .................................................................................4 Output Terminal ........................................................................................................
PAGE 8
\ If you accidentally damage or lose any parts they can be replaced with ease. The following are parts that came with your system and their reference model numbers so you can continue to effectively monitor your premises. PRODUCT MODEL# DESCRIPTION Power Adapters Audio/Video Cable Your product software and manual are available for download at: SOFTWARE/ MANUALS http://www.SVAT.com/downloads.php ADDITIONAL ACCESSORIES You may wish to add to your system and upgrade some components of it.
PAGE 9
FCC NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.