Digital Wireless Camera CA531 Digital Wireless Monitor M723 User Manual
Features • 7’’ portable LCD monitor • Pan-Tile camera • Record video to SD card • Crystal clear pictures with higher frame rate • 2-way talkback function •Remote activated night light • Room temperature display and alerts • Audio only function •3 different baby lullabies • Single, two-channel or quad display • Night vision 20ft • Digital zoom function for a closer look • Rechargeable Lithium battery for up to 2.
Wireless Receiver 1. SCAN Button – When the SCAN button is pressed, the screen is turned off. Durning this time the parent unit will continuously scan the camera ( or multiple cameras). When a sound is detected, the parent unit will become active. The screen is turned back, now you can see what happen in the baby room. You can adjust the sound sensitivity for this detection in VOX. After the monitor has detected sound it will take about 5 seconds to switch back to the scan mode.
2) while all the connected cameras have been displayed, press again to enter Quad mode, 3)In Quad mode, press once again to enter Auto sequency mode, then press again to exit the Auto sequency mode 12. Zoom- The video can be set at normal or double size by pressing the zoom button. When the video is in double size mode, navigating the joystick button can be used to view the parts outside the parent unit screen. Press the zoom button again to return to normal size.
Wireless Receiver Installation 1. Place the receiver in a place that will have clear reception with your camera(s). 2. Plug the AC adaptor power output cable into the 5V POWER input of the cradle or receiver. Plug the power plug into a wall outlet or surge protector. 3. Leave the receiver to charge for several hours prior to first time use so the built-in rechargeable receiver battery is fully charged. DO NOT remove the power cable from the receiver / from the cradle during initial charge process.
Night Vision This camera has built-in IR LEDs, which provides the camera with the ability to view images in no/low light conditions. It is important to use the provided power adaptor (and not the batteries) when using the camera for prolonged periods in low light conditions, as the built-in IR LEDs will drain the battery more quickly than regular daytime use.
Viewing Mode 1. Signal Indicator – The signal indicator shows the strength of the signal being received from the camera. The number of bars in the signal indicator shows the strength of the signal – One or No Bars indicates the signal is poor, and 4 bars indicate a very strong signal. Signal Indicators: 2. Channel Indicator – Displays the current channel number. Press the cam button on the receiver to switch between available cameras. 3.
7 Zoom indicator- it displays on the screen while the video is setted in double size 8 Overwritten indicator- displays if the SD card is allowed to overwrite files when it is full. 9 New recording indicator- new recordings are saved on the SD card. 10 Battery Indicator- indicates the monitor battery’s life 11 Sound indicator- when the volume has been decrease to mute, the mute icon will be displays on the screen.
Main Menu The Main Menu contains five submenus 1. Alert In scan mode, Press the joystick button left or right to decrease or Increase the volume of the buzzer when motion or Vox is detected by the camera(s). If you want to turn off the buzzer or button sounds, turn the alert volume to the minimum setting(Default 0) 2. Camera Use the menu to add camera(s) to the receiver, adjust the camera on/off, adjust the brightness for camera. 1) Pairing The system comes with camera(s) that have already been paired.
e) A message will be display on the screen. The screen will count down from 30 to 0. You have to briefly press the pair button on the baby unit within this f) Press the Pair button on the back of the camera. Once the camera has been paired, it will be immediately viewable on the receiver monitor.
2) Format SD Card- select Yes to format the micro SD card. Formatting will delete all the data stored on the micro SD card 3) Default Setting- select Yes to reset the parent unit to factory default setting. All menu settings will then be reset 4) Language setting- select the language( English, Spanish, French) as per your interest 5) Temperature unit- select the temperature unit you want to use.
Select OFF to disable the temperature alert 4 Vox set the vox sensitivity ( high, medium, low, off ) by joystick button, and press in to confirm setting 5 Overwrite Decide whether to record over earlier recorded files when the memory of the Micro SD card is full Troubleshooting If you have problems with the system, there is often a quick and simple solution. Please try the following: Problem No picture from a camera The picture is dropping Audio problems Solution 1.
The picture is or has become choppy The picture may become choppy when experiencing a lower frame rate (i.e. 10 frames per second vs. a higher 20 frames per second). 1. Try moving the camera closer to the receiver. 2. Remove obstructions between the receiver and camera. 3. Adjust the monitor antenna to vertical position. Specifications Lcd monitor Receiving Frequency Range 2400Mhz~2483.
FCC NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.