Indoor | Outdoor 45245 Home Monitoring Wireless Add-on Color Camera User Manual For indoor/outdoor use www.jascoproducts.
Table of Contents Product Features .................................................................... 3 Package Contents .................................................................. 4 Choosing A Camera Mounting Location ..................... 4 Long Range Night Vision .................................................... 6 Multi-Camera Systems ........................................................ 6 Camera Channel Selection ................................................ 7 Installation .........
Thank you for purchasing the GE Wireless Add-on Color Camera. This product is intended for use as an add-on camera for the GE Home Monitoring Surveillance Systems. Please review these instructions carefully before attempting to operate the camera. PRODUCT FEATURES • Weather resistant metal camera casing, designed for outdoor use. • Black anodized finish prevents rust and unwanted reflections • Long Range Night Vision — high-powered LED’s allow you to see up to 60ft. in the dark.
PACKAGE CONTENTS Please check and identify all the parts before proceeding with the installation. 1. Wireless Add-on Color Camera 2. Wall mounting hardware (3 screws, 3 plastic anchors) 3. AC adapter 4. Adjustment wrench CHOOSING A CAMERA MOUNTING LOCATION The Wireless Add-on Color Camera is desiged to be mounted to a wall. It is suitable for indoor or outdoor use. When choosing a mounting location, please be advised: • The wireless camera must be used with a GE Wireless Home Monitoring system.
mounting plate so that the cable can exit the cable ran on the outdoor surface. The cable can also be routed out the bracket and along a wall and/or ceiling keeping it hidden/protected. • The universal multi-axis bracket allows you to mount at almost any angle. • DO NOT position the camera so that it points directly into the sun or any bright light as this may cause damage to the camera.
• The Camera has an unobstructed wireless transmission range up to 200 ft. from the receiver. Transmission distance indoors is reduced due to interior walls, wiring, household fixtures and metal plumbing. LONG RANGE NIGHT VISION The 45245 Wireless Color Camera features Long Range Night Vision tech20 Infrared nology. Objects and images (IR) LEDs can be seen in little or no light up to 60 ft. The camera uses a special image Sensor sensor that automatically detects available light levels.
Wireless Camera Systems - 45234, 45236, 45239, 45246. Each system can accept a maximum of two cameras. CAMERA CHANNEL SELECTION Each wireless camera must be assigned to a specific channel (1 or 2) through the use of a slide switch located on the inside of the camera housing. First slide off the sun shield and then unscrew the lens from the camera. The receiver or monitor must have its channel selection set to the same corresponding number.
INSTALLATION Wall Mount or Ceiling Mount — you will need: - Drill - 3/8" Drill bit (if running cable thru wall or ceiling) - 1/8" drill bit (for drilling screw pilot holes if mounting into wood or non-brick material) - 3/16" drill Bit (for drilling holes for plastic anchor s if mounting onto drywall or brick material) - a screwdriver. - Adjustment wrench (included) Step 1.
Step 2. Cable routing -IMPORTANT (a) If running the cable along the wall surface, position cable through slot at base of mounting bracket before installing mounting bracket (see figure A). Figure A (Running cable on surface of wall) Pilot holes for mounting screws (b) If the cable needs to be ran through a wall or ceiling, then an additional hole will need to be drilled using the 3/8” drill bit. Drill the hole in the center of the three mounting screw holes (see figure B).
Step 3. Mounting bracket (a) If mounting to a stud, wood surface or other non-brick material, use the 1/8” drill bit to drill pilot holes; drill holes. Align holes in mounting bracket to drilled holes, insert screws and screw in until plate has secure fit. Do not over tighten screws. (b) If mounting to drywall or brick material, use plastic anchors (see Figure C). Using 3/16” drill bit (masonry bit, if drilling into brick), drill holes and insert anchors into drilled holes for snug fit.
Proper (d) Take care to position the Position camera in the correct Channel orientation. To ensure Selection the camera image is not Lens positioned upside down, Light you may have to rotate Sensor the camera housing so the channel slelection switch is positioned above the lens and the light sensor is below the lens. 1 2 Step 4. Antenna Adjustment Once mounted adjust the camera’s antenna to achieve best reception.
Step 5. AC Power Locate the power cable end connection. Attach the AC adapter (labeled ‘camera’) to end of cable coming from the camera. Plug-in AC adapter to nearest AC outlet. Adapter must be used in a dry location. AC power extension cables are available from the Call Center 1-800-654-8483 or visit online at www. jascoproducts.com TROUBLE SHOOTING If you are having trouble operating this product, please consult the guide below.
Blank monitor 1. Make sure receiver or monitor is switched ON, and the correct video input has been selected. 2. Ensure AC adapters are completely plugged into the socket and the camera and/or receiver’s power indication light is on. Interference on camera picture 1. Make sure each camera (transmitter) is within range, and that no large obstructions are blocking the signal. 2. Try repositioning the camera, monitor (receiver) or both to improve the reception quality. 3.
Audio problems 1. Ensure the volume is turned up sufficiently on the Monitor (or TV). 2. Make sure the sound is within the microphone range. 3. If the unit emits a loud wailing sound (feeds back), try moving the camera away from the receiver or angle the receiver differently.
SPECIFICATIONS (Subject to change without notice.) CAMERA TV System .....................................................................................................NTSC Integrated Lens.................................................. 6.0mm, F1.5 fixed focus Resolution........................................................................... 510x496 TV Lines Image Sensor.................................................................................. 1/3” CMOS Min. Illumination .................
ONE-YEAR LIMITED WARRANTY Jasco Products Company warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
FCC STATEMENT WARNING This device complies with part 15 of the FCC rules. Operation is subject to Risk of fire and shock • Only use the supplied cUL listed AC to DC adapter. the following two conditions: • The supplied adapter is for indoor use only. (1) This device may not cause harmful • Do not run the camera cable inside walls; when securing the cable, do not cut or puncture interference.
Notes
Notes
is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114 www.jascoproducts.com 45245 rev.
