e Manual

ManualsBrandsRCBS ManualsToolsQuick Change High Capacity Powder Measur

PRECISIONEERED RELOADING EQUIPMENT

We think that we make the very best reloading equipment in the world. If you

agree, please tell your friends. If you disagree, tell us we want to do

something about it!

Customer Service

1-800-533-5000 (US or Canada) or 530-533-5191

Hours: Monday - Thursday, 6:30am - 4:00pm Pacific Time

(hours may vary)

e-mail: rcbs.tech@atk.com or visit our website at www.rcbs.com

RCBS 605 Oro Dam Blvd. East Oroville, CA 95965

ALLIANT POWDER - CCI - CHAMPION TRAPS & TARGETS

EAGLE - ESTATE CARTRIDGE - FEDERAL AMMUNITION

FUSION AMMUNITION - GUNSLICK PRO - NITREX - OUTERS

RCBS – RAMLINE - SHOOTERS RIDGE - SPEER – WEAVER

7200545/0210

QUICK CHANGE HIGH CAPACITY

POWDER MEASURE

WARNING: NOT FOR USE WITH BLACK POWDER!

PRODUCT INSTRUCTIONS

*Shown with optional Powder

baffle – sold separately

Summary of content (6 pages)

PAGE 1
PRECISIONEERED RELOADING EQUIPMENT QUICK CHANGE HIGH CAPACITY POWDER MEASURE We think that we make the very best reloading equipment in the world. If you agree, please tell your friends. If you disagree, tell us we want to do something about it! Customer Service 1-800-533-5000 (US or Canada) or 530-533-5191 *Shown with optional Powder baffle – sold separately Hours: Monday - Thursday, 6:30am - 4:00pm Pacific Time (hours may vary) e-mail: rcbs.tech@atk.com or visit our website at www.rcbs.
PAGE 2
WARNING Before using the RCBS Quick Change High Capacity Powder Measure, read these instructions carefully to fully learn how to safely operate the related reloading equipment. Failure to properly operate the related reloading equipment can result in severe personal injury and/or equipment damage. If you have any questions while assembling or operating this tool, Call us at 1-800-533-5000 or 1-530-533-5191 Monday – Thursday 6:30 am – 4:00 pm Pacific Time (hours may vary) Or email us at rcbs.tech@atk.
PAGE 3
Key# Description Part # Qty 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 QC HC Main Casting QC HC Powder Hopper QC HC Powder Hopper Cap QC HC Measuring Cylinder QC HC Metering Screw QC HC Metering Screw Bushing Metering Screw Lock Ring Bow Washer QC HC Drain Tube Handle Assembly Handle Screws QC Locking Pin Assembly 7/8"-14 Hex Lock Ring Drop Tube Large .50 cal Drop Tube Small .22-.270 cal Drop Tube Medium .
PAGE 4
• DO NOT store primers in bulk. The blast of just a few hundred primers is sufficient to cause serious injury to anyone nearby. • DO NOT force primers. Use care in handling primers. • DO NOT have more than one can of powder on the bench at one time. Powder cans should be stored away from the bench to avoid picking up the wrong one. • DO NOT use any powder unless its identity is positively known. The only positive identification is the manufacturer's label on the original canister.
PAGE 5
easily by pulling the pin and changing Metering Assemblies. Metering Assemblies can be left preset for future charges. DRAINING POWDER HOPPER It is not necessary to empty the powder hopper each time you change charges unless a different powder is required. Powder should not be left in the measure as it will deteriorate and may clog and jam the measuring cylinder and etch the powder hopper.
PAGE 6
up for right or left handed use depending on which way you slide in the assembly. TO USE Before attempting to throw a series of powder charges, set the powder measure for the maximum charge and run about a pound of powder through it. This will deposit a film on the inside of the measure and help the powder flow through more evenly and consistently. Be sure you use the same uniform movements for each powder charge. To throw a charge, raise the handle until it comes to the end of the stroke with a light tap.