NOTE: The unit must be traveling at least 3 mph (5 km/h) before motor will engage. Kick to start to at least 3 mph (5 km/h) while applying the throttle to engage motor. OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice.
HEADLINE CONTENTS Safety Warnings..............................................................................................1-2 Before You Begin................................................................................................3 Assembly and Set-Up.........................................................................................4 Charging the Battery..........................................................................................4 Pre-Ride Checklist...........................
HEADLINE SAFETY WARNINGS USING THE CHARGER The charger supplied with the electric scooter should be regularly examined for damage to the cord, plug, enclosure and other parts. In the event of such damage, the scooter must not be charged until the charger has been repaired or replaced. Use only with the recommended charger. Use caution when charging. The charger is not a toy. Charger should be operated by an adult. Do not operate charger near flammable materials.
HEADLINE BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES.
HEADLINE AND SET-UP ASSEMBLY Attaching the Handlebars WARNING: Do not attempt to thread the stem into the front fork thread. Required Tool: 5 mm Allen Wrench (included) Note: Make sure any cables/wires are out of the way before inserting the stem into the fork. 1 Before inserting the T-bar onto the fork, carefully pull the connector through the rubber protector to remove. Discard the rubber protector.
HEADLINECHECKLIST PRE-RIDE Brake Safety Gear Wheels Laws and Regulations Frame, Fork and Handlebars Insurance Check the brake for proper function. When you step on the rear-fender brake, the brake should provide positive braking action. When you apply the brake with the throttle on/ engaged, the brake cut-off switch should cut power to the motor. Always wear proper protective gear, such as an approved safety helmet. Elbow pads and kneepads are recommended.
HEADLINE USAGE To Connect to your Bluetooth® Speaker WARNING: Do not talk or text on your mobile device while riding. Only change your device’s music settings when stationary. 1 Turn Razor Sonic Glow electric scooter power switch ON. 2 Activate Bluetooth® in your 3 Find Razor Sonic Glow in your handheld device’s settings. handheld device’s list and select. 4 Play your music.
REPAIR AND MAINTENANCE Turn power switch “OFF” before beginning repair or maintenance: • Read the instructions • Remove charger plug • Turn the power switch OFF • Secure the unit under repair • Exercise caution around exposed parts • Contact Razor customer service if unsure about any repair or maintenance Front Wheel Replacement Required Tools: Two (2) 5 mm Allen Wrenches (one included) Note: Front wheel hardware sequence 7-3 7-1 7-2 7-3 7-4 7-2 7-1 Right Side 7-2 Spacer 7-3 Bearing 7-4 Large Spacer
REPAIR AND MAINTENANCE Note: When re-inserting the motor wires into the connector, make sure the blue wire connects to the blue wire, the green wire connects to the green wire, the yellow wire connects to the yellow wire and the multicolored wire connects to the multicolored wire. Note: 5 Disconnect motor cables. Motor Blue 6 Using two (2) 5 mm Allen wrenches, loosen the axle bolt. Remove wheel/hub motor.
TROUBLESHOOTING GUIDE *Unit(s) should be turned OFF and fully charged prior to doing any troubleshooting. NOTE: All troubleshooting steps should be performed by an adult only. Problem Possible Cause Solution Does not work out of the box Unit must be traveling at least 3 mph (5 km/h) before motor will engage Kick to start to at least 3 mph (5 km/h) while pressing down on the thumb throttle to engage motor. Loose connection(s) Check for loose connections/wires underneath the deck plate.
ELECTRIC SCOOTER PARTS Keep your scooter running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar Grips (Left/Right) 2. Handlebar Stem 2-1 Throttle 2-2 Speaker Cover 2-3 Speaker 2-4 T Bar Front Cover 2-5 T Bar Lights 2-6 Bluetooth Module 2-7 T Bar Rear Cover 3. 4. 5. 6. 7. 8. 9.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE HEADLINE FCC ID: 2AGU6006 IC: 21056-006 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.