Installation Manual Part 6

ManualsBrandsRaytheon IIS ManualsElectronicsAir-Ground Radio System

EXHIBfi' C

C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM

FCC ID: CDG-ARTU

MAGNASTAR

MagnaStar Aircraft Configuration Settings

Aircraft Tail Number Date:

Svstem Confil!uration Settinl!s:

Maintenance Pa88code:

Billing Node:

Aircraft Aircall NUmber:

Direct Call pickup:

Aircraft Satcom Terminal ID:

Call waiting:

Node (AItJ):

Satcom ~edance (AItJ):

Satcom Node (ArO):

Aero-I Satcom Dialing:

Aero-B+ Satcom Dialing:

Auto Link Switchz

Dialing Plan:

'800 MOD" Call Randoff Mode:

9600 MODBM Call Bandoff Mode:

CAS Service Indicator:

Auxilary Call Alerter Cadence:

PC Station uplink Call Mode:

Programm8d Speed Dial Humber8 z

HI' Decay Settingz

HI' Sen.e Setting:

HP Label:

HP P'1'T:

Direct I Credit Card

PIN:

Y/R

Y/N

Satc~ I GroundCell

Bighl Low

Band.et I PBX

Bnabled/Di8ahled

Bnabled/Diabled

Bnab1ed/Di8ahled

US-Canada I Mexico

BDabled/Di8ab1ed

BDabled/Diabled

Air-Ground/Satc~/QrouDdCe11

0113456789

Voice/FAX/TDD

Y I N

8Dabled/ Di .&bled

Handset Confi2uration Settin2s:

Hand..t location: - -

Inplane Number Assigned a 0 1 2 3 4 5 6 7 8 9

Inplane Label: -

Station Aircall Numbera Station Aircall pin:

Ring Handset w/Aircraft Aircalla

Linka Air-Oround/Satc~

Satc~ Station Terainal IDa - --

Ring Handset w/Aircraft Satc~ Term. ID: TIN

Station Type: Cockpit/Cabin/Pax/Mod../TDD/PC

Station Baud Rate: 4800bp. I 9600bp.

Hand.et Ringera BDabl84 I Di.abl84

Hand..t Alerter Gain:

Hand..t RJ-ll Gaina

Hand..t Coar.. Speaker Gain a ._-

Handset pine Speaker Gaina

Hand..t Voice Sidetone Gaina

Hand..t D'l'KP Oain: - --

Hand..t DTNP IIoni tor Scale a

Hand..t DTNP Moni tor Sen.e a .

Hand..t Coar.. Microphone Tx Gaina ---

Hand..t pine Microphone Tz Gaina --

Auxiliary Call Alerter: 012 3 4 567 8 9

Call In progre.. Indicator a ~l84/Di.abl84

Inplane LBD Blink Ratea

uplink LBO Blink Rate:

Y/R

Hand..t location:

Inplane II'W8b8r A8.igne4a 0 1 2 J 6 5 , 7 8 9

Inplane Label:

Station Aircall II'W8b8ra

Station Aircall pin a Ring Handset -/Aircraft Aircalla T/R

LiDJr.: Air-Ground/ satc~

Satcom Station Ter8dnal %Da

Ring Handset -/Aircraft Satc~ Te~. %Da Y/R

Station Type: Cockpit/Cabin/rax/~eaJTDD/PC

Station Baud Rate: 6800bp. /9600bp.

Hand..t Ringer: BDabled / Di8able4

Hand..t Alert.r Gain:

Hand..t RJ-11 Gaina -

Hand..t Coar.. Speaker Gaina

Hand..t Fine Speaker Gain: . ~~ ~

Band..t voice sid.tone Gaina

Hand..t D'rIIJ' Gain: -

Hand..t DTMF Noni tor Scale a

Band..t D'rIIJ' Noni tor Seu.e a

Hand..t Coar.. Microphone '1'X Gaina ,

Hand..t Fine Kicrophone '1'x Gaina

Auxiliary Call Al.rter: 012 3 6 5 , 7 8 9

Call In Progr... Indicator a BDable4/Di8able4

Inplane LBD BliDJr. Rat.a

UpliDJr. LBD BliDJr. Rate:

Speed Diu' " .

i 1 . !C:;i" Speed D a ~~: i~~c

Speed Dial' ::~"

Speed Dial' c',...",,'

Speed Dial' ~

Summary of content (16 pages)

PAGE 1
EXHIBfi' C FCC ID: CDG-ARTU C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM MAGNASTAR MagnaStar Aircraft Configuration Settings Aircraft Tail Number Date: Svstem Confil!uration Settinl!s: Maintenance Pa88code: Billing Node: Aircraft Aircall NUmber: Direct Call pickup: Terminal ID: Call waiting: Y/N Satc~ I GroundCell Bighl Low Band.
PAGE 2
FCC ill: COG-ARTU EXHIBITC C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM MAGNASTAR MagnaStar Aircraft Configuration Settings Aircraft Tail Number Date: Inplan. Labela Inplane Y/R Aircalla T.rminal ID: - Band..t Band..t D'l'KF ~ni DTIIF ~ni Bands.t Coar.. Call In Inplan. Uplink Gaina ~ GaiDa Indicatora Rate: - - Hand.et Inplane Inplane Station B\uaber Aa.igned I Labell Aircall RU8b8r: Station Aircall -- Pinl 0123'5678.9 Hand.et Alerter RJ-ll aain I . Hand.et voice Hand.
PAGE 3
FCC ID: CDG-ARTU - - Station Aircall R\l8ber1 Station Aircall pins Ring Band.et -/Aircraft Aircalll T/R Link I Air-GrouDd/Satc~ Satcom Station Terminal ID: Ring Band.et -/Aircraft Satcom Te~. ID: T/R Station Type: Cockpit/Cabin/Fax/Nodea/TDD/PC Station Baud Ratel j800bp. l'fOObp. Band..t Ring.r: 8Dabled I Diaabled Band..t Al.rt.r Gain: Band..t RJ-ll Gain I Band..t Coar.. Speak.r ~iD 1 Band..t Fine Speak.r ~inl ~,,: , Band..t Voice sid.tone ~iDl I'~ Band..t D'1'IIF ~in: Band..t DTKF Monitor Scal.: Band..
PAGE 4
EXHIBrrc FCC ID: CDG-ARTU MAGNASTAR 8.0 C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM MMT SOFTWARE LOADING This section covers loading of MMT software onto the MMT host computer. The host computer must be a 386 or faster IBM compatible computer with 4 Megabytes of RAM. a 3.5" high density floppy drive. and at least 1 Megabyte of memory available for use on the hard drive. For the MMT software to run property it is important that the C: partition is no larger than 1.
PAGE 5
9-i Menu Menu "".." ""' ' Menu Configuration Installation/Test Menu , Boot Radio Radio '."..".'."' Operations Menu MMT MMT MMT """ Menu BIT Menu. C-2000 C-2(xx) C-2(xx) Test - - Menu Maintenance Debug """"""""".""".."" STATION "" """"""'" PASSCODE GENSTARGROUND """"'.".""'.' CONCLUSION Informatio. ACCESS Verification USING STATE .
PAGE 6
FCC ID: CDG-ARTU MAGNAST AR EXHIBIT C C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.2 MMT COMMUNICATION VERIFICATION The MMT Communications Verification test assures that the MMT software is properly communicating with the ARTU by checking the version of software that is loaded in the ARTU. - Symptom: "ERROR=>MMT communications failure timed out" The ARTU and the MMT are not communicating when this information is displayed in the Radio Responseswindow.
PAGE 7
FCC ID: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.3 START ARTU OPERATIONAL SOFTWARE When the ARTU is powered up with an MMT connected,the ARTU software will not execute and will be in what is termed a "boot" mode. When commandedby the MMT, the ARTU will start the operational software. The first step in starting the operational is for the ARTU to run Built-In-Test (BIT). The normal BIT processbegins by turning "ON" the ARTU Fault indicator.
PAGE 8
FCC 10: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE + TELEPHONE SYSTEM V4. OA NNT Radio Response + I I I I : Power-up Statu8, 80376 Kicroproc...or OK. SRAH ox. : ARTC code Pile ARTCC4OB.HIX Ver 0.0 Date 04/06/00 : 14,25 BaDk 1 CRC,~: DSP code Pile KDSPC40A.HIX Ver 0.0 Date 03/27/00 12,13 BaDk 2 CRC,1298: BIT code pile MBITC40A.HIX Ver 0.0 Date 05/18/99 16,03 BaDk 1 CRC,209C: Boot code Pile ~31C.HBX Ver 0.0 Date 04/24/'6 14,27 BaDk 1 CRC,B8& : : Radio sottware is not executing.
PAGE 9
FCC 10: CDG-ARTU EXHIBIT C MAGNAST AR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.4 LOCKED OFF-LINE STATE For the MMT to command certain tests for the installation checkout, the ARTU software must be placed in a mode which will allow the ARTU the flexibility to perform these tests. This mode of operation is called the "Locked OFF-Line State". This test step is a mode changeonly. Failure of this mode change will only occur iftbe MMT is not communicating with the ARTU.
PAGE 10
~ FCC 10: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.5 ARTU MOUNTING TRAY FAN TEST Under normal operational conditions, the ARTU Mounting Tray Fan is activated by a switch in the ARTU which is under software control. The ARTU monitors a temperature sensor located in the ARTU and is programmed to turn on the Fan when the temperatureis at approximately room temperature. The ARTU Mounting Tray Fan test will command the ARTU to turn the fan "ON" to check operation.
PAGE 11
FCC 10: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.6 ARTU TRANSMITTER OUTPUT POWER During the ARTU Transmitter Output Power test, the ARTU will transmit a CW signal at a frequency of 894.9495 MHz. The power level transmitted by the ARTU will be 10 watts minimum. Measurementof the transmitted signal should be made as close to the Antenna as possible to check the functionality of the greatestnumber of the C-2000 components.
PAGE 12
~ FCC ill: CDG-ARTU EXHmrr C MAGNAST AR C-2000 DIGITAL AIRBORNE ~.~ +t i C-2000 reports eagiDeeriDQ teat TELEPHONE MMT Radio R88p0D8" ~ INITIAL PA ~ perfo~. ,DS1Al09 , I : ~t~: : : Wait SYSTEM , v4~ : 81'1 aR>ear. .tuck. for tha *1'I : to properly .-cute c~ : to AR'fU (5-10 Me). t : ~t08: Low output power / No output power. : H.-ure the output p~r directly out of the AR'ro. If the power : me&8Ur..-Dti. incorrect replace the AR'ro. If the power8ea8Ur888Dti.
PAGE 13
FCC ID: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.7 ARTU RECEIVE SIGNAL STRENGTH MEASUREMENT The ARTU Receive Signal Strength measurementtest will verify the complete RF portion of the C-2000 system. This test will require the use of a MagnaStar Loop-Around test box. During this test a 16 QAM signal is transmitted by the ARTU.
PAGE 14
FCC ill: CDG-ARTU MAGNASTAR EXHIBIT C C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM Pr'-' F2 to View Status Display : SY8f{)tom, us Value alUch lower than ~kings a) Are the ON/OFF and Attenuator awitches : : : : : b) c) : Tutorial I8rr + :mSlA20l VlA + + on Loop-Around in the correct Is the battery voltage greater than 6 volts? .ove ~e Loop-Around Test Cable connection plac_t Replace cables or C-2000 RP components one at a time faulted Teat Box. po8ition? : : : on the Ant~a.
PAGE 15
FCC 10: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.8 HANDSET I LAN TEST The HandsetI LAN test wilt inform the installer of the number ofCDBRs/AIUs and Handsetswith which the ARTU can cornrnunicate. This test does not distinguish the difference between a CDBR or an Am. Also, this test will not identify the presenceof a CAS. Symptom: The MMTI does not respond with the correct number of CDBRs or Handsets.
PAGE 16
~ FCC ill: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 9.1.9 RESET MAINTENANCE ACCESS PASSCODE This test step will reset the Maintenance Access Passcodeto the factory setting of 0000. If the Maintenance Access Passcodewas previously set to a value other than 0000 for protection purposes,then the installer will want to reprogram the desired passcodeinto the system after completing the system checkout.