Bracket Guide

ManualsBrandsRaytec ManualsAccessoriesPole Mount Bracket for 2x Illuminators

BRACKET SUMMARY

AI CIRCULAR BRACKET

Supplied as standard with all Raytec adaptive illuminators. Provides a large degree of ﬂexibility of mounting options. Can be attached

directly to a wall, ceiling and any of the brackets listed in this document.

300 series is supplied with a larger version of this bracket.

25 series is supplied with a U-Bracket.

Assembly Notes: Access to the back of the bracket maybe

limited, it is possible to remove U/AI Circular / Large AI Circular

bracket from illuminator. Mount AI circular bracket to area of

your choice - ﬁx illuminator to its AI circular bracket as shown

below. Set the vertical angle of illumination then tighten screws.

49.50

72.00

300 Series AI 25 and Fusion Products

www.rayteccctv.com

UK Tel: +44 (0) 1670 520055 Fax: +44 (0) 1670 819760

Americas Tel: +1 613-270-9990

Summary of content (9 pages)

PAGE 1
BRACKET SUMMARY AI CIRCULAR BRACKET Supplied as standard with all Raytec adaptive illuminators. Provides a large degree of flexibility of mounting options. Can be attached directly to a wall, ceiling and any of the brackets listed in this document. 300 series is supplied with a larger version of this bracket. 25 series is supplied with a U-Bracket. 25 and Fusion Products 72.00 300 Series AI 49.
PAGE 2
VARIO U Bracket Supplied as standard with all Raytec VARIO illuminators. Provides a large degree of flexibility of mounting options. Can be attached directly to a wall, ceiling and any of the brackets listed in this document. VARIO 2 VARIO 4 VARIO 8 Assembly Notes: You will need a 4mm allen/hex key to remove the button socket screws when adjusting the VARIO U Bracket. UK Tel: +44 (0) 1670 520055 Fax: +44 (0) 1670 819760 Americas Tel: +1 613-270-9990 www.rayteccctv.
PAGE 3
WB1 WALL BRACKET Designed to mount Raytec illuminators to walls or to Raytec PBC brackets (see page 3 and 4) to provide full pan/tilt adjustment when used with AI circular bracket. Assembly Notes: Mount WB1 to wall or Raytec PBC-1/ PBC-2. Mount illuminator to WB1 as shown below. Set the vertical/horizontal angle of illumination then tighten screws. UK Tel: +44 (0) 1670 520055 Fax: +44 (0) 1670 819760 Americas Tel: +1 613-270-9990 www.rayteccctv.
PAGE 4
PBC-1 Designed to mount Raytec illuminators to circular poles / columns. To fit poles approx minimum 50mm up to 170mm (other diameters available on request). Provides flat mounting platform for 1x RAYMAX or RAYLUX illuminator and Voyager Range. (PSU mounted elsewhere) Large Circular Bracket Assembly Notes: Mount PBC-1 to pole using mounting clips – position and tighten.
PAGE 5
PBC-2 Pole Bracket Clamp for 2x RAYMAX or RAYLUX illuminators and Voyager range. Assembly Notes: Mount PBC-2 to pole using mounting clips – position and tighten. Mount illuminators as per PBC-1. (see page 3) PBC-PSU-ADAP Adaptor plate to allow the additional mounting of PSU to pole. (see ordering table on page 5) UK Tel: +44 (0) 1670 520055 Fax: +44 (0) 1670 819760 Americas Tel: +1 613-270-9990 www.rayteccctv.
PAGE 6
PBC-PSU-ADAP (continued...
PAGE 7
SB1 SInGLE PAn & TILT BRACKET ADAPTOR Designed to mount any Raytec illuminator (normally 1 unit) to a Top Mount Pan/Tilt (PTZ) motor. The bracket should be fitted between camera housing and PTZ motor. Mounting holes provided to match with most industry standard PTZ units. Several mounting options provided to mount Raytec illuminator. Other versions available for specific PTZ motors. Ø8.00 150 .00 00 9. 21 200 .00 25 350 14 1. .
PAGE 8
DB2 Double Pan & Tilt Bracket Adaptor Designed to mount any Raytec illuminator (normally 2 units) to a Top Mount Pan/Tilt (PTZ) motor. The bracket should be fitted between camera housing and PTZ motor. Mounting holes provided to match with most industry standard PTZ units. Several mounting options provided to mount Raytec illuminator. Other versions available for specific PTZ motors. 21 9. 00 Ø8.00 141 .25 160 .00 550 .00 25 1.
PAGE 9
PB-180/ PB-360 Designed to mount Raytec illuminators to poles / columns – for use mainly with dome cameras. Mounts to top of pole. Provided with 4” PCD (101.6mm) and 2” (61.5mm) PCD mounting options. PB-360 supplied with 4 mounting areas to mount up to 4 illuminators. PB-180 supplied with 2 mounting areas (plus spacer) to mount up to 2 illuminators. 294 101.6 mm (4”PCD) 61.