Quick Start Guide

ManualsBrandsRaytac ManualsElectronicsPressure Control Module

PRESSURE CONTROL MODULE

Part Number: 0830001

QUICK START GUIDE

ARB Pressure Control provides the capability to inflate/deflate tyres and other inflatable accessories to a user settable pressure.

It can be quickly and easily fitted to an ARB compressor, and can be controlled using the ARB Pressure Control App, which is

available for download from Google Play and Apple App store.

The kit contains:

- ARB PCM (Pressure Control Module). This is the brains of the kit, communicating with the smartphone app, pressure sensor

and activating the solenoid valves to control the inflation/deflation.

- ARB PRV (Pressure Regulating Valve)

- ARB pressure sensor

- wiring harness

PCM Wiring Harness PRV Pressure Sensor

To connect an ARB hose for tyre inflation the following hardware is also required:

- ARB Remote Hose Coupling Mount Kit (#171314)

- Reinforced hose (range of lengths from 0.3 to 3.0m, #0740201 – 06)

- 1/8 BSP to JIC-4 adapter fitting (#0740105), for connecting the reinforced hose to the PRV.

Installation

The PRV can be screwed directly into the compressor manifold 1/8 BSP port. Or it can be remotely mounted from the

compressor on a manifold kit (#171503). The PCM should be positioned high in the engine bay, or inside the vehicle cabin,

within 1m [3ft] of the PRV for wiring connection. Avoid very hot areas such as the exhaust. The PCM is water resistant, but

should be orientated with the opening facing downwards to avoid water accumulating inside the module. Also avoid very

confined spaces that might impact on the Bluetooth connection with the smartphone app.

One of the PRV input ports (inward pointing arrows) comes with a 1/8 BSP fitting pre-

installed with sealant, screw it into one of the 1/8 BSP ports on your compressor

manifold, or alternate compressed air supply. If desired the pre-installed nipple can be

relocated to the other input port on the opposite side of the PRV.

Note: Always use thread sealant or PTFE tape to seal all tapered threaded joints. O-

ring sealed parallel threaded joints do not require sealant or tape.

Latest Revision Date: 09/06/2020 Page 1 of 7

Summary of content (7 pages)

PAGE 1
PRESSURE CONTROL MODULE Part Number: 0830001 QUICK START GUIDE ARB Pressure Control provides the capability to inflate/deflate tyres and other inflatable accessories to a user settable pressure. It can be quickly and easily fitted to an ARB compressor, and can be controlled using the ARB Pressure Control App, which is available for download from Google Play and Apple App store. The kit contains: - ARB PCM (Pressure Control Module).
PAGE 2
PRESSURE CONTROL MODULE 2. Install the pressure sensor into a regulated output port (outward pointing arrows) of the PRV. Any of the PRV regulated output ports may be used, select the regulated output port that best suits your installation configuration. 3. Attach the two connectors of the wiring harness to the two solenoid coils of the PRV. Note that the connector with the purple wire should be matched only with the deflate valve coil (shown on the right directly opposite to the exhaust fitting).
PAGE 3
PRESSURE CONTROL MODULE 8. Connect the Remote Hose Coupling Mount Kit (171314) to a regulated output port of the PRV. Any of the PRV regulated output ports may be used, select the regulated output port that best suits your installation configuration. If the PRV is installed and connected as described above, the finished assembly should look like this.
PAGE 4
PRESSURE CONTROL MODULE Part Number: 0830001 Smartphone App The ARB Pressure Control App can be downloaded from the Google Play Store or Apple App Store. Search for “Pressure Control”. To connect to the PCM it must be powered on. So if wired as described earlier, turn on your vehicle ignition and switch on the compressor. Follow these steps to connect the app to the PCM for the first time. After opening the app the first step is to connect to your PCM. Tap the settings icon.
PAGE 5
PRESSURE CONTROL MODULE Part Number: 0830001 When connect the app appearance will change, allowing interaction with all the features.
PAGE 6
PRESSURE CONTROL MODULE Part Number: 0830001 The main app features are: Current pressure readout Target pressure for Pressure Control mode. Set this by tapping on the underlined text, or by selecting from the pressure preset list Tap the pressure preset list to select from your 4 available pressure presets.
PAGE 7
PRESSURE CONTROL MODULE Part Number: 0830001 ARB PRODUCTS WARRANTY AGAINST DEFECTS ARB warrants the ARB Products against defects in workmanship and materials for the Warranty Period. If defective workmanship or materials become apparent in the Warranty Period, ARB will replace or repair the defective Product. The benefits to the customer given by this warranty are in addition to other rights and remedies of the customer under a law in relation to the goods or services to which the warranty relates.