User Manual and Installation Guide Proxy Mobile Reader Nano Inline www.proxy.com | support@proxy.com Last updated: April 27, 2020 Revision 3.
Contacts For additional offices around the world , see h ttps://www.proxy.com/contact Proxy,Inc. San Francisco (Global Headquarters) 500 3rd Street #245 San Francisco, CA 94107 USA Proxy Technical Support:https://support.proxy.com/hc/en-us | 2 User Manual and Installation Guide: Mobile Reader Nano Inline This document may have been updated since printing — for the latest, please visit h ttps://proxy.
Table of Contents Introduction 4 Mobile Reader Nano Inline 4 Functionality 4 Dimensions 4 Product Details 5 Installation Details 5 Parts List 5 Reader Specifications 6 Wiring Information 6 Mobile Reader Nano Inline 6 External Antenna Information 7 Antenna Installation 7 External Antenna Details 9 Reader Installation Details 10 Install Videos 10 Install Steps 10 Power Up and Testing 10 Recommended Infrastructure 11 Installation in a Turnstile, Elevator Panel, or Other Encl
Introduction The Proxy Mobile Reader Nano Inline is installed between a controller and an access control reader. When users present their credential (card, key fob, fingerprint, etc.) to the reader, the reader passes the Wiegand command to the controller. The access control system then grants or denies access to the secure location. The Nano Inline is Bluetooth Low Energy (BLE) enabled.
Product Details Model Name: Mobile Reader Nano Inline Device Type: Mobile Credential: Bluetooth Low Energy (BLE) Type of Equipment: Unsealed controller board Suitable for Indoor use only Interface Type: Screw Terminal Block (4 Position x 2) Operating Voltage Range: 5V - 24V DC (12V recommended) Current Draw: 30 mA @ 12V(Ble Transmitter Power Setting=7) Power Consumption: 0.
Reader Specifications Model / Version(s) Operating Voltage Current Rating Nano Inline 5V - 24V DC 30 mA @ 12V(Ble Transmitter Power Setting=7) Operating Temperature -35° to 66°C (-31° to 149°F) 5 to 95% RH (non-condensing) Do not operate at a voltage above 24V DC as it will damage the hardware Wiring Information Mobile Reader Nano Inline Input / Output Colors G (Ground) D1 (Wiegand Data 1) D0 (Wiegand Data 0) V+ (DC+ Voltage) 1.
External Antenna Information Important: Do not kink or bend the antenna cable during installation as this will permanently damage the cable. Instead, carefully loop any extra length of antenna cable. Antenna Installation 1. Open the enclosure and remove the reader assembly 2. Locate the existing reader’s pigtail and identify the Power/GND and D0/D1 wires. The Nano Inline will connect to these wires. Do not connect them at this time. 3. Locate sufficient space to mount the Nano Inline a.
5. Connect the antenna cable to the Nano Inline via the u.FL connector. It’s important the connector goes in centered on the pin in the center. You will feel it click into place. If not, don’t force the connector as this can break the pin. 6. You can throw away the antenna cable you didn’t use or keep it as a spare.
External Antenna Details Antenna I:146153-0300 ● Operating Range: 2400~2500MHz ● Antenna Type: Dipole ● Efficiency: >63% ● Bandwidth (VSWR: 2.0 max.) 140 MHz / SWR < 2.0 ● Polarization: Linear ● Radiation: Omni directional ● Antenna Gain: 2.2dBi ● Impedance: 50 ohm ● Antenna: 34.9mm x 9mm / 1.4" x 0.4" ● Weight: 1.174g Antenna I:146153-0150 | 9 ● Operating Range: 2400~2500MHz ● Antenna Type: Dipole ● Efficiency: >72% ● Bandwidth (VSWR: 2.0 max.) 140 MHz / SWR < 2.
Reader Installation Details Install Videos Proxy Nano Inline Installation on Vimeo Install Steps 1. Open the enclosure and remove the reader assembly 2. Locate the wiring harness and identify the V+/GND and D0/D1 wires 3. Connect the Nano to the existing wiring per the Wiring Instructions 4. Locate sufficient space to mount the Nano Inline a.
3. Provision Nano － Refer to the P rovisioning Guide to provision to your Proxy organization and sync to the local Access Control System Recommended Infrastructure 1. All cabling and wiring shall be UL Listed or UL Recognized 2. All readers shall be powered by a UL Listed power-limited power supply, or power-limited output from a UL Listed control panel 3.
Installation in a Turnstile, Elevator Panel, or Other Enclosure The optimal placement of the external antenna is against the glass pane where the current access control reader exists. These glass panes are typically designed to allow for radio signals to pass through with minimal interference, which is preferred for the Bluetooth Low Energy (BLE) signal from the Nano Inline for connection to the Proxy ID mobile app.
Nano Inline Wiring Certifications FCC Tune up power table BLE ● Each product is programmed with the pre-defined RF parameters ● Each products RF power level is measured to ensure the power level does not exceed the target power level, in a fully calibrated setup ● These settings cannot be changed Please find below the Maximum Transmit Power for production units: Average Output Power (dBm) Band / Mode Bluetooth LE BLE 5.
● ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help RF Exposure Information This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body. Information to user This device complies with part 15 of the FCC Rules.
IC Tune up power table BLE ● Each product is programmed with the pre-defined RF parameters ● Each products RF power level is measured to ensure the power level does not exceed the target power level, in a fully calibrated setup ● These settings cannot be changed Please find below the Maximum Transmit Power for production units: Average Output Power (dBm) Band / Mode Bluetooth LE BLE 5.0-2M GFSK GFSK 8 8 This device complies with Industry Canada’s licence-exempt RSSs.
Innovation, Sciences et Développement économique Canada a approuvé l'utilisation de ce transmetteur radio avec les types d'antenne énumérés ci-dessous, le gain maximal admissible étant indiqué. Les types d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal indiqué pour tout type listé sont strictement interdits pour une utilisation avec cet appareil. Types d'antennes:Dipole Gain d'antenne (en dBi):2.8dBi/2.
Install Troubleshooting Possible Symptoms Likely issue How to resolve Reader LED is not illuminating on Nano Either wiring at the reader or at the power supply has been disconnected. Double check Power supply is both connections to bring the reader back disconnected or not online. Lack of power to the ACS system may supplying enough voltage also cause this- double-check the wiring connecting the reader to the panel.
