User Manual and Installation Guide Proxy Mobile Reader Nano Connect www.proxy.com | support@proxy.com Last updated: May 11, 2020 Revision 3.
Contacts For additional offices around the world , see h ttps://www.proxy.com/contact Proxy,Inc. San Francisco (Global Headquarters) 500 3rd Street #245 San Francisco, CA 94107 USA Proxy Technical Support:https://support.proxy.com/hc/en-us | 2 User Manual and Installation Guide: Mobile Reader Nano Connect This document may have been updated since printing — for the latest, please visit h ttps://proxy.
Table of Contents Introduction 4 Mobile Reader Nano Connect 4 Functionality 4 Dimensions 4 Product Details (Nano Connect) 5 Installation Details 5 Parts List 5 Reader Specifications 6 Wiring Information 6 Mobile Reader Nano Connect 6 External Antenna Information 7 Antenna Installation 7 External Antenna Details 9 Reader Installation Details 11 Install Videos 11 Install Steps 11 Power Up and Testing Recommended Infrastructure Certifications CE AU 11 12 13 17 17 Install Tro
Introduction The Proxy Mobile Reader Nano Connect is installed between a controller and an access control reader. When users present their credential (card, key fob, fingerprint, etc.) to the reader, the reader passes the Wiegand command to the controller. The access control system then grants or denies access to the secure location. The Nano Connect is Bluetooth Low Energy (BLE) enabled.
Product Details (Nano Connect) Model Name: Mobile Reader Nano Connect Device Type: Mobile Credential: 2.4GHz (Bluetooth Low Energy) Type of Equipment: Unsealed controller board Suitable for Indoor use only Interface Type: Molex Connector, 4-pin, plug (x2) Operating Voltage Range: 5V - 24V DC (12V recommended) Current Draw: 30 mA @ 12V(Ble Transmitter Power Setting=7) Power Consumption: 0.
Reader Specifications Model / Version(s) Operating Voltage Current Rating Nano Connect 5V - 24V DC 30 mA @ 12V(Ble Transmitter Power Setting=7) Operating Temperature -35° to 66°C (-31° to 149°F) 5 to 95% RH (non-condensing) Do not operate at a voltage above 24V DC as it will damage the hardware Wiring Information Mobile Reader Nano Connect Input / Output Colors G (Ground) D0 (Wiegand Data 0) D1 (Wiegand Data 1) V+ (DC+ Voltage) 1.
External Antenna Information Important: Do not kink or bend the antenna cable during installation as this will permanently damage the cable. Instead, carefully loop any extra length of antenna cable. Antenna Installation 1. Open the enclosure and remove the reader assembly 2. Locate the existing reader’s pigtail and identify the Power/GND and D0/D1 wires. The Nano Connect will connect to these wires. Do not connect them at this time. 3. Locate sufficient space to mount the Nano Connect a.
6. You can throw away the antenna cable you didn’t use or keep it as a spare. Antenna Attachment for the Nano Connect Harness Attachment for the Nano Connect | 8 User Manual and Installation Guide: Mobile Reader Nano Connect This document may have been updated since printing — for the latest, please visit h ttps://proxy.
Antenna Attachment for the Nano Connect External Antenna Details Antenna :206994-0100 | 9 ● Operating Range: 2400~2500MHz ● Antenna Type: Monopole ● Efficiency: >55% ● Bandwidth (VSWR: 2.0 max.) 140 MHz / SWR < 2.0 ● Polarization: Linear ● Radiation: Omni directional ● Antenna Gain: 3.6dBi ● Impedance: 50 ohm ● Antenna: 15.4mm x 6.4mm / 0.6" x 0.3" ● Weight: 0.
Antenna I:146153-0150 ● Operating Range: 2400~2500MHz ● Antenna Type: Dipole ● Efficiency: >72% ● Bandwidth (VSWR: 2.0 max.) 140 MHz / SWR < 2.0 ● Polarization: Linear ● Radiation: Omni directional ● Antenna Gain: 2.8dBi ● Impedance: 50 ohm ● Antenna: 34.9mm x 9mm / 1.4" x 0.4" ● Weight: 0.724g | 10 User Manual and Installation Guide: Mobile Reader Nano Connect This document may have been updated since printing — for the latest, please visit h ttps://proxy.
Reader Installation Details Install Videos Proxy Nano Connect Installation on Vimeo Install Steps 1. Open the enclosure and remove the reader assembly 2. Locate the wiring harness and identify the V+/GND and D0/D1 wires 3. Connect the Nano to the existing wiring per the Wiring Instructions 4. Locate sufficient space to mount the Nano Connect a. Locate behind the existing reader closest to the base of the existing reader’s pigtail 5. Attach the antenna. Refer to A ntenna Installation. 6.
Recommended Infrastructure 1. All cabling and wiring shall be UL Listed or UL Recognized 2. All readers shall be powered by a UL Listed power-limited power supply, or power-limited output from a UL Listed control panel 3. Linear DC Power Supply [5–24VDC, 30 mA @ 12V(Ble Transmitter Power Setting=7)] Do not exceed 24V The Nano Connect operates at very low current ratings. If operating with the need for more precise ratings of low current draw, please contact Proxy directly.
Certifications FCC Tune up power table BLE Each product is programmed with the pre-defined RF parameters Each product RF power level is measured to ensure the power level not exceeding the target power level, in a fully calibrated setup ● These settings cannot be changed Please find below the Maximum Transmit Power for production units: ● ● Average Power (dBm) Band / Mode Bluetooth LE BLE 5.
Information to user This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Proxy, Inc. could void the user's authority to operate the equipment.
IC Tune up power table BLE ● ● ● Each product is programmed with the pre-defined RF parameters Each products RF power level is measured to ensure the power level does not exceed the target power level, in a fully calibrated setup These settings cannot be changed Please find below the Maximum Transmit Power for production units: Average Output Power (dBm) Band / Mode LE BLE 5.0-2M GFSK GFSK 8 8 Bluetooth This device complies with Industry Canada’s licence-exempt RSSs.
Antenna 2 types:Dipole Antenna 2 gain (in dBi):2.8dBi Innovation, Sciences et Développement économique Canada a approuvé l'utilisation de ce transmetteur radio avec les types d'antenne énumérés ci-dessous, le gain maximal admissible étant indiqué. Les types d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal indiqué pour tout type listé sont strictement interdits pour une utilisation avec cet appareil. Types d'antennes 1:Monopole Gain d'antenne 1 (en dBi):3.
CE Tune up power table BLE ● ● ● Each product is programmed with the pre-defined RF parameters. Each product RF power level is measured to ensure the power level not exceeding the target power level, in a fully calibrated setup. These settings cannot be changed. Please find below the Maximum Transmit Power for production units: Average Power (dBm) Band / Mode Bluetooth LE BLE 5.
RF Exposure Information This device meets the EU requirements and the International Commission on Non-Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. Hereby, Proxy, Inc., declares that the radio equipment type Mobile Reader Nano Connect is in compliance with Directive 2014/53/EU.
Install Troubleshooting Possible Symptoms Likely issue How to resolve Reader LED is not illuminating on Nano Power supply is disconnected or not supplying enough voltage Either wiring at the reader or at the power supply has been disconnected. Double check both connections to bring the reader back online. Lack of power to the ACS system may also cause thisdouble-check the wiring connecting the reader to the panel.
