Version: A Issued Date: 2020/07/02 Approval Sheet (產品承認書) 產品名稱 (Product): Bluetooth Low Energy Module 產品型號 (Model No.
Index 1. Overall Introduction ...................................................................................................... 3 1.1. Application ............................................................................................................ 3 1.2. Features ............................................................................................................... 4 2. Product Dimension .................................................................................................
1. Overall Introduction Raytac’s MDBT42TV & MDBT42TV-P is a BT 5.1 stack (Bluetooth low energy or BLE) module designed based on Nordic nRF52805 SoC solution, which incorporates: GPIO, SPI, UART, I2C, and ADC interfaces for connecting peripherals and sensors. Features: 1. Dual Transmission mode of BLE & 2.4Ghz RF upon customer preference. 2. Compact size with (L) 8.3 x (W) 5.8 x (H) 1.3 mm. 3. Low power requirements, ultra-low peak, average and idle mode power consumption. 4.
1.2. Features ‧Multi-protocol 2.
2. Product Dimension 2.1. PCB Dimensions & Pin Indication ‧MDBT42TV PCB Size (in mm) Min. L W H Norm MAX. 8.3 - 0.15 5.8 1.3 + 0.
‧MDBT42TV-P PCB Size (in mm) Min. L W H Norm MAX. 8.3 - 0.15 5.8 1.3 + 0.
2.2. Recommended Layout of Solder Pad Graphs are all in Top View, Unit in mm.
2.3. RF Layout Suggestion (aka Keep-Out Area) Please follow below instruction to have better wireless performance. Make sure to keep the “No-Ground-Pad” as wider as possible when there is no enough space in your design. No-Ground Pad should be included in the corresponding position of the antenna in EACH LAYER. Place the module towards the edge of PCB to have better performance than placing it on the center. Welcome to send us your layout in PDF for review at service@raytac.
Examples of “NOT RECOMMENDED” layout 2.4. Footprint & Design Guide Please visit “Support” page of our website to download. The package includes footprint, 2D/3D drawing, reflow graph and recommended spec for external 32.768khz.
2.5. Pin Assignment Pin No. Name Pin function Description (1) GND Ground The pad must be connected to a solid ground plane (2) SWDIO Digital I/O Serial Wire debug I/O for debug and programming (3) SWDCLK Digital input Serial Wire debug clock input for debug and programming P0.21 Digital I/O General-purpose digital I/O (4) RESET Configurable as system RESET pin (5) P0.20 Digital I/O General-purpose digital I/O (6) P0.14 Digital I/O General-purpose digital I/O (7) P0.
3. Main Chip Solution RF IC Crystal Frequency Nordic NRF52805 32MHZ 32MHz crystal is already inside the module.
4. Specification Any technical spec shall refer to Nordic’s official documents as final reference. 4.1. Absolute Maximum Ratings 4.2.
4.3. Electrical Specifications 4.3.1. General Radio Characteristics 4.3.2.
4.3.3. Radio Current Consumption (Receiver) 4.3.4. Transmitter Specification 4.3.5.
4.3.6.
4.3.7. RX Intermodulation 4.3.8.
4.3.9. RSSI Specifications 4.3.10. CPU 4.3.11.
5. FCC Compliance This equipment has been tested and found to comply with the limits for a Class digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to the radio communications.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation.
accordance with FCC multi-transmitter product procedures. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 5mm may be maintained between the antenna and users.
6. IC Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Antennas This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antennes Cet émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous avec le gain maximal admissible indiqué .
7. NCC 警語 根據 NCC 低功率電波輻射性電機管理辦法規定 LP0002 低功率射頻器材技術規範_章節 3.8.
