Version: A Issued Date: 2016/03/24 Approval Sheet (產品承認書) 產品名稱 (Product): BT 4.2 Module (nRF52832) 產品型號 (Model No.): MDBT42Q Series Advantage of MDBT42Q series: 1. Long working distance: over 80 meters in open space.
Index 1. Overall Introduction ...................................................................................................... 1 1.1. Application ............................................................................................................ 1 1.2. 1.3. Features ............................................................................................................... 2 Profile & Service Information ................................................................................
1. Overall Introduction Raytac’s MDBT42Q is a BT 4.0, BT 4.1 and BT 4.2 stack (Bluetooth low energy or BLE) module designed based on Nordic nRF52832 SoC solution, which incorporates: GPIO, SPI, UART, I2C, I2S, PWM and ADC interfaces for connecting peripherals and sensors. Features of the module: 1. Dual Transmission mode of BLE & 2.4Ghz RF upon customer preference. 2. Compact size with (L) 16 x (W) 10 x (H) 2.2 mm. 3. Low power requirements, ultra-low peak, average and idle mode power consumption. 4.
1.2. Features ‧Multi-protocol 2.
1.3.
2. Product Dimension 2.1. MDBT42Q Series ‧PCB Dimensions, Pin Indication and Layout Guide PCB SIZE: (L) 16 x (W) 10 x (H) 2.
5
6
7
8
2.2. Pin Assignment Pin No. Name Pin function Description (1) GND Ground (2) P0.25 Digital I/O General-purpose digital I/O (3) P0.26 Digital I/O General-purpose digital I/O (4) P0.27 Digital I/O General-purpose digital I/O P0.28 Digital I/O General-purpose digital I/O AIN4 Analog input P0.29 Digital I/O AIN5 Analog input P0.30 Digital I/O AIN6 Analog input P0.
Pin No. Name Pin function Description P0.09 Digital I/O General-purpose digital I/O NFC1 NFC input NFC antenna connection P0.10 Digital I/O General-purpose digital I/O NFC2 NFC input NFC antenna connection (24) GND Ground (25) P0.11 Digital I/O General-purpose digital I/O (26) P0.12 Digital I/O General-purpose digital I/O (27) P0.13 Digital I/O General-purpose digital I/O P0.
2.3. GPIO Located Near the Radio Below remarks are extracted from Nordic’s nRF52832 Spec. Any updates shall refer to Nordic’s official release as final reference. 3.
4. Specification 4.1. Absolute Maximum Ratings 4.2. Operation Conditions 4.3. Electrical Specifications 4.4.
4.5. Radio Current Consumption (Transmitter) 4.6.
4.7. Transmitter Specification 4.8. Receiver Operation 4.9.
4.10.
4.11. Radio Timing Parameters 4.12.
4.13. CPU 4.14.
5. FCC Compliance This equipment has been tested and found to comply with the limits for a Class digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to the radio communications.
installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: SH6MDBT42Q Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
6. IC Caution This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: ．This device may not cause interference ．This device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
7.
22
