User's Manual

User Pin Number Registration
Please perform while door is open Default Pin Number is [1, 2, 3, 4].
Don’t forget your Pin Number.
If you forgot your Pin Number, New registration of Pin Number,
RFID Card, Fingerprint, Guest Pin Number and Remote Control is not possible.
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Registration Mode, press the [1] button.
4. Enter 4~12 digits New User Pin Number and press the [#] button.
5. Re-Enter the New User Pin Number
and press the [Registration] button to complete the process.
ㆍOnly 1 user Pin Number can be saved.
ㆍWhen error occur during registration [2] will be lighted together with an error sound.
ㆍDuring each process, when [Registration] button is pressed,
the registration process will end.
ㆍWhen the registration process has completed, a completion sound will be heard.
Note
Product Line-Up
EPIC product lineup. Check main features of each product carefully.
Note
Registration
Deletion
The number pad lighting is as follows, during registration and
deletion, the numbers that are lighted when the number pad is
touched are as follows, products containing each function will all
be lighted.
[1] Pin Number Registration & Deletion
[2] RFID Card Registration & Deletion
[3] Fingerprint Registration & Deletion
[4] Guest Pin Number Registration & Deletion
[5] Remote Control Registration & Deletion
[0] User Registered Information & Settings Reset
This is a unified manual of EPIC products.
Products features may change for improvement purposes.
Contents of this manual may be modified without prior notice.
ES-100D
ES-S100D
ES-300D
ES-500D
ES-500H
ES-700G
ES-F300D
ES-F500D
ES-F500H
ES-F500HK
ES-F700G
ES-FF730G
ES-7000K
ES-9000K
ES-F9000K
EF-P8800K
MODEL LIGHTING FUNCTION
Pin Number
Pin Number + RFID Card
Pin Number + RFID Card
Pin Number + RFID Card
Pin Number + RFID Card
Pin Number + RFID Card + Fingerprint
Pin Number + RFID Card + Fingerprint
Pin Number + RFID Card + Fingerprint
Pin Number + RFID Card + Fingerprint + Mechanical Key
Pin Number + RFID Card + Mechanical Key
Pin Number + RFID Card + Mechanical Key
Pin Number + RFID Card + Fingerprint + Mechanical Key
Pin Number + RFID Card + Fingerprint + Mechanical Key
R
D
[1],[4],[5]
[1],[4],[5],[0]
R
D
[1],[2],[4],[5]
[1],[2],[4],[5],[0]
R
D
[1],[2],[3],[4],[5]
[1],[2],[3],[4],[5],[0]
R
D
[1],[2],[4],[5]
[1],[2],[4],[5],[0]
R
D
[1],[2],[3],[4],[5]
[1],[2],[3],[4],[5],[0]
R D
Registration Deletion
Pin Number + RFID Card + Fingerprint (Outer / Inner body)
+ Mechanical Key
Pin Number + RFID Card (Outer / Inner body)
+ Mechanical Key
Pin Number + RFID Card (Outer / Inner body)
+ Fingerprint + Mechanical Key
User RFID Card Registration (all-at-once)
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Registration Mode, press the [2] button.
4. Place the Card to be registered on the card reader.
When the Card has been successfully registered,
the 3 digits Card Placement Number will be displayed on the number pad
and registration is complete.
(If you want to register additional Card, repeat step 4.)
5. When registration of all Card is done,
press the [Registration] button to complete the process.
User RFID Card Registration (one-by-one)
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Registration Mode, press the [2] button.
4. Enter the Card Placement Number from 001~200
on the number pad followed by the [#] button.
(When the selected Card Placement Number is already in use,
the error sound will be heard and [7] button will be lighted
on the number pad.)
5. Place the Card to be registered on the card reader.
When the Card has been successfully registered,
the 3 digits Card Placement Number will be displayed on the number pad
and registration is complete.
(If you want to register additional Card, repeat step 4.)
6. When registration of all Card is done, press the [Registration] button
to complete the process.
ㆍUp to 200 cards can be registered.
ㆍNew registration will not delete previously registered card in the system.
Note
User Fingerprint Registration (all-at-once)
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3.
After entering the Registration Mode, press the [3] button.
4. Check the total number of the registered Fingerprint displayed
on the number pad, then enter the Fingerprint to be registered for 4 times.
When the Fingerprint has been successfully registered,
the 3 digits Fingerprint Placement Number will be displayed
on the number pad and registration is complete.
(If you want to register additional Fingerprint, repeat step 4.)
5. When registration of all Fingerprint is done,
press the [Registration] button to complete the process.
ㆍUp to 100 Fingerprints can be registered.
ㆍY
ou can also re-register registered Fingerprints.
ㆍ
When error occur during registration LED [2] will be blinking.
Note
User Guest Pin Number Registration
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Registration Mode, press the [4] button.
4. Enter 4~12 digits User Guest Pin Number and press the [#] button.
5. Re-Enter the User Guest Pin Number
and press the [Registration] button to complete the process.
ㆍIf you register a new guest Pin Number, the old one will be deleted.
ㆍ
Only 1 Guest Pin Number can be saved. It will be deleted after 1 usage.
Note
User Fingerprint Registration (one-by-one)
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Registration Mode, press the [3] button.
4. Check the total number of the registered Fingerprint displayed
on the number pad, enter the Fingerprint Placement Number
from 001~100 on the number pad followed by the [#] button.
(When the selected Fingerprint Placement Number is already in use,
the error sound will be heard and [7] button
will be lighted on the number pad.)
5. Enter the Fingerprint to be registered for 4 times.
When the Fingerprint has been successfully registered,
the 3 digits Fingerprint Placement Number will be displayed
on the number pad and registration is complete.
(If you want to register additional Fingerprint, repeat step 4.)
6. When registration of all Fingerprint is done,
press the [Registration] button to complete the process.
User Remote Control Registration (all-at-once)
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3.
After entering the Registration Mode, press the [5] button.
4. Press the [Open] button of the Remote Control to be registered.
When the Remote Control has been successfully registered,
the 3 digits Remote Control Placement Number will be displayed
on the number pad and registration is complete.
(If you want to register additional Remote Control, repeat step 4.)
5. When registration of all Remote Control is done,
press the [Registration] button to complete the process.
If the Remote Control receiver module is not connected and number [5]
button does not light up, the Remote Control cannot be registered.
User Remote Control Registration (one-by-one)
1. Open the battery cover and press the [Registration] button.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Registration Mode, press the [5] button.
4. Enter the Remote Control Placement Number from 001~010
on the number pad followed by the [#] button.
(When the selected Remote Control Placement Number is already in use,
the error sound will be heard and [7] button will be lighted on the screen.)
5. Press the [Open] button of the Remote Control to be registered.
When the Remote Control has been successfully registered,
the 3 digits Remote Control Placement Number will be displayed
on the number pad and registration is complete.
(If you want to register additional Remote Control, repeat step 4.)
6. When registration of all Remote Control is done,
press the [Registration] button to complete the process.
ㆍThe Remote Control module should be installed on the unit to work.
ㆍUp to 10 Remote Controls can be registered.
ㆍNew registration will not delete stored ones in the unit.
Note
If the Remote Control receiver module is not connected and number [5]
button does not light up, the Remote Control cannot be registered.
User RFID Card Deletion (all-at-once)
1. Open the battery cover and press the [Registration] button for 3 seconds.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Deletion Mode, press the [2] button.
4. When the number pad turns on press the [#] button for 5 seconds.
The melody will be heard and all registered Cards will be deleted.
User RFID Card Deletion (one-by-one)
1. Open the battery cover and press the [Registration] button for 3 seconds.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Deletion Mode, press the [2] button.
4. Enter the registered Card Placement Number from 001~200
to be deleted followed by the [#] button.
(If you want to delete additional Card, repeat step 4.)
5. When specific Card is deleted,
press the [Registration] button to complete the process.
User Fingerprint Deletion (all-at-once)
1. Open the battery cover and press the [Registration] button for 3 seconds.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Deletion Mode, press the [3] button.
4. When the number pad turns on press the [#] button for 5 seconds.
The melody will be heard and all registered Fingerprints will be deleted.
User Fingerprint Deletion (one-by-one)
1. Open the battery cover and press the [Registration] button for 3 seconds.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3.
After entering the Deletion Mode, press the [3] button.
4. Enter the registered Fingerprint Placement Number from 001~100
to be deleted followed by the [#] button.
(If you want to delete additional Fingerprint, repeat step 4.)
5. When specific Fingerprint is deleted,
press the [Registration] button to complete the process.
User Remote Control Deletion (all-at-once)
1. Open the battery cover and press the [Registration] button for 3 seconds.
2. Enter the User Pin Number followed by the [#] button.
(First registration: Initial User Pin Number [1, 2, 3, 4] + [#] button.)
3. After entering the Deletion Mode, press the [5] button.
4. When the number pad turns on press the [#] button for 5 seconds.
The melody will be heard and all registered Remote Control will be deleted.
The default Pin Number is [1, 2, 3, 4].
Please change to new Pin Number.
Ensure not to use consecutive or
repetitive numbers for your safety
.
REV.04
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help
Rule Part 15.21: The users manual or
instruction manual for an intentional or
unintentional radiator shall caution the
user that changes or modifications not
expressly approved by the party
responsible for compliance could void
the user's authority to operate the
equipment