C5 by Installation manual NCR 6632 1
Content Considerations before installing C5 ........................................................................................................................................ 3 List of conditions where C5 should not be installed: .............................................................................................................. 3 What is C5 ........................................................................................................................................................
Considerations before installing C5 Before installing C5 to an ATM, visually inspect the ATM to detect any abnormalities that could negatively affect the regular functionality of C5. In case you face any of the problems listed below quit the installation. List of conditions where C5 should not be installed: Evidence of vandalism (broken bezel, open or broken fascia, unscrewed side panels, broken screws, damaged dispenser etc.
FCC Compliance Information OTCaccess C5 controller with FCC ID: 2A4FC2105 OTCaccess MiniSmart Bluetooth Keypad with FCC ID: 2A4FC2303 The devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) the devices may not cause harmful interference, and (2) the devices must accept any interference received, including interference that may cause undesired operation.
C5 ports Bottom 1 2 3 4 1. Power 5. Motor 1 9. Motor 2 NCR 6632 Top 5 6 7 2. USB Type B 6. Door Switch 10. Motor 3 8 9 3. Analog Keypad 7. Digital Output 11. RS 232 13. RJ45 Ethernet 10 11 12 13 4. Keypad 8. Door switch 12.
Preparing the Beauty Door 1. Remove the outer door 2.
3. Put the hole template on the upper left corner of the door. Mark locations 4. With a drill bit, drill 4mm holes on edges and 20 mm hole in the middle 5. Clean the holes from inside 6.
7. Unscrew the lock 8. Fit the lock fixing plate on the front. Secure the plate with M4 nuts from the back. Insert the lock 9. Fix the lock in place with its nut from the back 10.
Preparing the safe door 1. Unscrew the 2 metal pieces from the steel door of the safe 2. Install the new striker pieces instead. Fix them with two M4x10 RYSB bolts Removal of the existing safe lock 1. Open the safe door. Unscrew the inner guard metal plate NCR 6632 2.
3. Remove the metal plate 4. Unscrew the screws of the lock 5. After removing the cover, unscrew the existing lock. 6.
7. Remove the lower protective metal NCR 6632 8.
Keypad installation 1. Remove the black round part on the safe door of the ATM 2. Remove the bolt on the right side of the keypad and keep it 3. Mount the bottom cover of the keypad to the safe door using the existing screw places (4 units M4x12 bolt) 4.
5. Assemble the front and the back of the keypad 6. Screw the bolt you kept (check step 2) back firmly. New lock installation 1. Take the lock lift plate NCR 6632 2.
3. Mount the new lock in place with 3xM6x30 YSB bolts. You don’t have to reassemble the lower metal part. Attach BVK OTC19 cable to the lock Note! Make sure you keep the protective metal plate of the lock until the end of the installation. Installation of C5 1. Take BVK anchoring plate and place C5 on it NCR 6632 2. Fix C5 to the plate with 4 x 2.
ç 3. Place the plate so that it is on the right side of the lock 4. Set the plate in place with 2xM6x15 RYSB using the existing holes Top box lock installation 1.
2. Pair the lock with its plate 3. Place the plate over where the old locks where and mark. Do it for both locks 4. Drill 2 x 3 mm holes for both locks 5. Fix the plate with M4x12 RYSB bolts.
Top box cables 1. Lock attached to the front door 2. Already existing cables on the front door 3. Already existing cables on the front door 4.
The way is shown by this stick 5. Cable way inside ATM 6. Cable way inside ATM 7.
8.
ATM Safe box preparation 1. Fix the cable protection plates into the already existing wholes on the left bottom wall of the safe 2. Fix the upper cabinet lock cables as shown in the photo to avoid damage 3. Place the cables as shown in the photo 4. Connect the cables to the PoE adapter.
5. Cable passage 6. Cable passage 7.
8. Mount the magnetic door switch plates into the existing holes on the door and floor of the safe with M4 bolts. Place the wired door switch on the door. Place its counterpart onto the floor. Fix the switches with M3x5 YSB bolts 9.
10. Screw the protection metal plate to the door of the ATM, you might need it in case you will need to remove the lock and store it lately. 11. Connect the cables to C5 reffering to page 4 „C5 ports” - Keypad cable – port No. 4 - Magnetic door switch cable – port No. 8 - Safe door lock – port No.10 - Ethernet (PoE) – port No.13 - 2 x top box lock – port No.