Chapter 8: Radar 189 small dots, while small targets remain visible and persistent. Gain levels further from your boat remain unchanged. Super HD adjustments You can generally use the default AUTO settings for best results, but two manual controls allow you to explore Super HD’s capabilities. Antenna boost This scales the effective antenna size. At zero, the effective antenna size matches its actual size. At 95, the effective antenna size is doubled.
190 E Series Networked Display Reference Manual To turn interference rejection off ENHANCE ECHOES softkey. 2. Toggle the setting to OFF on the INT REJECT softkey. 1. Press the Expansion The expansion function allows you to either override the pulse length or to give larger returns so targets are easier to see. To override the pulse length 1. Open the Radar Setup Menu. You can either use the MENU button, or press and hold the EXPANSION softkey. 2.
Chapter 8: Radar 191 This can be used to reduce the effects of rain and sea clutter. To switch scan to scan on or off 1. Press the ENHANCE ECHOES softkey. 2. Toggle to ON or OFF using the SCAN TO SCAN softkey. 3. Press OK. 8.12 Radar range You can zoom in or out to view the radar display at different scales. The scale is measured from the centre to the top of the window and is displayed in the left hand corner of the status bar.
192 E Series Networked Display Reference Manual Note: Radar range synchronization is not available when the chart motion mode is set to autorange, nor when the selected scanner is set to dual range. 8.13 Measuring distance, range and bearing You can measure distance, range and bearing in the radar application. Options for doing so are detailed in the table below. Functions Distances between points Range from Bearings your boat Range Rings Yes (approx.) Yes (approx.
Chapter 8: Radar 193 To find the bearing and range to an object 1. Move the cursor to the object’s position. 2. Read off the bearing and range in the databar. Bearing and range from your vessel to cursor D8402_1 Cursor The Variable Range Marker (VRM) and Electronic Bearing Line (EBL) The VRM/EBL softkey opens the toolbars shown below: Variable Range Marker A Variable Range Marker (VRM) is a circle of variable radius centred on your vessel’s position.
194 E Series Networked Display Reference Manual Electronic Bearing Marker An Electronic Bearing Line (EBL) is an on screen marker drawn from your position to the edge of the window. When this line is rotated to align with a target, the bearing relative to your current heading is measured and displayed on the ADJUST EBL softkey label. The data is also displayed if you select the EBL with the cursor. D8425_1 EBL To change the EBL reference from relative to magnetic or true, see page 187.
Chapter 8: Radar 195 To create a VRM or an EBL 1. Press the VRM/EBL softkey. 2. Toggle to ON with the VRM/EBL softkey. 3. To adjust settings, press either the ADJUST VRM or ADJUST EBL softkey and make changes with the rotary controller. To place a second VRM or EBL 1. Press the SET UP VRM/EBL 2 softkey. 2. Proceed as with VRM/EBL 1.
196 E Series Networked Display Reference Manual To unfloat a VRM or EBL 1. Press the VRM/EBL softkey. 2. Press the FLOATING EBL softkey (under SET UP VRM/EBL 2 if you are using a second floating VRM or EBL). 3. Select CENTER. 4. Press OK. 8.14 Using radar to track objects The TARGET TRACKING softkey opens the toolbars shown below: Target tracking functions are used to help avoid collisions. • Guard zones sound an alarm when an object comes within a specified range.
Chapter 8: Radar 197 6nm Head-Up D6832-2 Circular Guard Zone 6nm Head-Up Relative Motion Rings 1nm D6815_3 Sector Guard Zone You can adjust the sensitivity of guard zones on the Alarms Setup Menu. For more information, see Alarm Setup Menu on page 288. Guard zones only operate when the whole zone is displayed on the screen. To avoid inappropriate alarms, they become active ten seconds after being placed or edited. To place a guard zone 1. 2. 3. 4. 5. 6. 7. Press the TARGET TRACKING softkey.
198 E Series Networked Display Reference Manual Setting up MARPA You can customize the following parameters from the MARPA Options menu: Parameter Options Vector Length 0.5min, 1 min, 3 min, 6min, 12min, 30 min, 60 min The time period specified for drawing length of vectors. Target History Plots a target’s previous position at the specified intervals. The four most recent position points are displayed.
Chapter 8: Radar 199 • Inadequate heading data exists. Symptoms of such conditions are that acquisition is difficult and the MARPA vectors are unstable; the symbol wanders away from the target, locks on to the wrong target or changes to a lost symbol target. If any of these conditions are present, acquisition and tracking may need to be re initiated or, in some cases be impossible to maintain. Improving the quality of the heading data will reduce the effect of the other conditions.
200 E Series Networked Display Reference Manual If you change to a smaller range scale, targets may be beyond the range of your scanner and will be lost. In such cases, an on screen warning will indicate that the target is off screen. D6810_4 MARPA targets Closest point of approach Closest point of approach (CPA) graphics show vectors for your vessel and a selected target. (A vector is a line showing a predicted course.
Chapter 8: Radar 201 In relative motion mode, no vector extension of your boat is shown. The CPA line emerges from your own boat, with the target vector extension being shown as relative, not true. The text next to the target indicates its course and speed. Press SHOW DETAILS to display the calculated relative course and speed.
202 E Series Networked Display Reference Manual • Show the position and display vessel data for other AIS equipped vessels within a specified range of your boat. • Display voyage data (position, course, speed and rate of turn) of AIS equipped ves sels. • Display basic or detailed information for each target vessel including safety critical target data. • Set up a safe zone around your boat. • View alarm and safety related messages.
Chapter 9: Using the data application 203 Chapter 9: Using the data application 9.1 Introduction D9010_1 The data application enables you to view numeric data generated by the system or by instruments available on NMEA or SeaTalk. Selecting a data application To select a data application: 1. Select a page set that includes a data application: PAGE OK Highlight suitable page set with Digital Data application 2.
204 Selecting the data for display You can either select a panel of pre configured data or customize the application to display the data of your choice. Note: Panel selection is a local setting and will therefore only affect the individual dis play on which you are working.
Chapter 9: Using the data application 205 e.g. ACTIVE Move control to Digital Data window Select page including Digital Data application Select required panel type Selected panel type displayed D8466_1 WAYPOINT Customize the panels You can customize each panel by changing: • The panel name. • The size and number of data cells • The data contained in each cell. This data can include any transducer or internally calculated navigation data that is available on NMEA or SeaTalk.
206 E Series Networked Display Reference Manual Selecting cell data To select the data that is to appear in each cell: 1. Select the data group for the relevant panel e.g. Data Groups e.g. SAILING SELECT DATA... Press and hold relevant soft key Vessel Navigation Depth Environment Wind Time and Date Engine Select data group D9106_1 Highlight data group 2.
Chapter 9: Using the data application 207 = Split horizontally e.g. e.g. Heading 2960T Heading 2960T Speed 20.0kt Trip 13.85nm Cell for splitting selected SPLIT CELL Speed 20.0kt OK Depth Trip 48.5ft 13.85nm Soft key indicates direction of split Cell splits horizontally OR Split vertically e.g. e.g. Heading 2960T Heading 2960T Speed 20.
8 E Series Networked Display Reference Manual
Chapter 10: Autopilot Control 209 Chapter 10:Autopilot Control If you have a Raymarine autopilot installed, you can access some of its functions from the E Series display unit. WARNING:The autopilot functions available on the E Series display unit do not replace the autopilot control head. You must have a pilot control head installed before you enable or engage the autopilot. Emergency disengage You can disable the autopilot using the power key. 1. Press and release the power button. 2.
210 E Series Networked Display Reference Manual When the autopilot is engaged, or you hotspot an active route or waypoint, the toolbar gives you the following options: Table 10 1: Active Navigation Toolbar STOP GOTO/FOLLOW Opens the Pilot Control screen. If the autopilot is in track mode, the route complete alarm sounds. ADVANCE WAYPOINT Opens the Pilot Control screen and provides the AUTO and TRACK softkeys. The screen stays open until you choose either AUTO or TRACK.
Chapter 10: Autopilot Control 211 Autopilot Status Indicator An indicator in the top right corner of the display unit tells you the current status of the autopilot. Table 10 2: Autopilot status indicators Icon Autopilot mode Standby. Track. Auto. No autopilot detected. Autopilot alarm is active. 10.2 The autopilot control screen The Pilot Control pop up screen is displayed when you engage the autopilot in track mode, at waypoint arrival, or when you select it from the Setup Menu.
212 E Series Networked Display Reference Manual For a list of the softkeys available while the Autopilot Control screen is open, see Table 10 3, Autopilot Control Toolbar. Table 10 3: Autopilot Control Toolbar AUTO Engage the autopilot and hold the current course (avail able when the autopilot is in Track or Standby mode). ENGAGE PILOT TRACK STANDBY Track to the current target waypoint. Disengages the autopilot (only available when the autopi lot is engaged).
Chapter 10: Autopilot Control Press STANDBY to silence the alarm and disengage the autopilot. Press AUTO to silence the alarm and continue on the current locked heading with autopilot engaged.
214 E Series Networked Display Reference Manual
Chapter 11: Video 215 Chapter 11:Video 11.1 Introduction D7493_2 The video application allows you to use your E Series Display to view images from a video player, on board camera or DVD player. Your Display is supplied with cabling to connect to equipment using a composite input source. You can also connect s video inputs to your Display. Video images can only be seen by the Display they are connected to and are therefore not viewable across the E Series network.
216 E Series Networked Display Reference Manual Customizing the video application When you first use the video application, it defaults the input source type to Composite, labels the video images Video 1, 2, 3 or 4 and sets the Cycle Video option to OFF. You will need to change these defaults in the following circumstances: • If you have installed cabling for use with equipment using S video. • If you wish to give each video input a more meaningful name e.g. engine room, view stern etc., DVD player etc.
Chapter 11: Video 217 OK x2 1 2 3 4 Period VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 10secs Video Video Video Video 1... 2... 3... 4... S-VIDEO VIDEO 1 (S-VIDEO VIDEO 1) COMPOSITE VIDEO 3 COMPOSITE VIDEO 4 Video 2 mirrors your choice for Video 1 and can no longer be selected independently of Video 1. D8486_1 Video Setup Menu Cycle Cycle Cycle Cycle Cycle Note: Video 1 mirrors your choice for Video 2 and is no longer selectable. 4. Repeat steps 2 and 3 for Video 3.
E Series Networked Display Reference Manual Engine room Bridge Aft Stern PRESENTATION D7489-2 218 Cycling through the video inputs You can set up your video application to automatically cycle through the images being received. This is particularly useful if you have on board cameras and wish to use them to obtain a regular overview of your boat, engine room etc. Setting up a video cycle To specify which video inputs are to be included in the cycle and their order: 1.
Chapter 11: Video 219 Running the video cycle With a video application active: CYCLE VIDEO ON OFF D7490-3 PRESENTATION Note: You will not be able to change the aspect ratio, contrast, brightness or color lev els of any video image when the video cycle is running. Stopping the video cycle You can stop the video cycle at any time by either pressing any of the 4 video soft keys or by toggling the CYCLE VIDEO option to OFF.
220 E Series Networked Display Reference Manual
Chapter 12: Using the Course Deviation Indicator 221 Chapter 12:Using the Course Deviation Indicator 12.1 Introduction With your display receiving accurate heading and position information, you can use the Course Deviation Indicator (CDI) to monitor your course and accurately steer to a target waypoint. The CDI application is pre configured to display the CDI graphic. You can customize the panel to display any available data. 12.
222 E Series Networked Display Reference Manual Steering instructions The steering instructions below the rolling road tell you what correction is needed to maintain your course and arrive at the target waypoint.
Chapter 13: Using the Engine Monitor 223 Chapter 13:Using the Engine Monitor 13.1 Introduction The engine monitor application enables you to view information in the form of gauges and digital data, from up to three compatible engines. To provide a fast update rate, the engine data is transferred from the engine’s serial interface to your E Series display via NMEA2000/SeaTalk2. Note: For details of compatible engines and related software updates, please refer to the Raymarine website on www.raymarine.com.
224 E Series Networked Display Reference Manual i. With an engine monitor window active, select the Panel Setup Menu: Setup Panel Setup Menu... MENU GPS Setup... D8707_1 Select Panel Setup Menu ii. Set the number of engines: Panel Setup Menu Configure: Configure: Configure: Configure: Configure: ENGINE... ENGINE & FUEL... FUEL RESOURCES... ENGINE & RESOURCES... TWIN ENGINE...
Chapter 13: Using the Engine Monitor 225 13.3 The engine monitor display Engine data is displayed in a series of pre configured panels. Each panel contains a particular set or data. You can choose the panel that suits your requirements via the soft keys: Panel Type Engine Engine & fuel Fuel resources Engine & resources Multi engines (3) Tacho & engine hours Oil pressure Data content Engine coolant temperature Boost pressure Alternator Fuel level (tanks 1 & 2) Total fuel D8953_1 Fuel rate 13.
226 E Series Networked Display Reference Manual
Chapter 14: Weather (US only) 227 Chapter 14:Weather (US only) This application is only available for the Unites States. Weather information for the Rest of the World can be obtained via a Navtex receiver. Please refer to Chapter 13:Navtex. 14.1 Overview The weather application superimposes historical, live and forecasted weather graphics on a world map. It also provides textual forecasts and warnings.
228 E Series Networked Display Reference Manual Pre requisites for using the weather application For your E Series to display weather data, your system must be connected to a Raymarine SR100 Sirius weather receiver which is supplying the appropriate data. For your vessel to be displayed and for weather reports to be available at your position, you will need a fix for your boat’s position and be within US coastal waters.
Chapter 14: Weather (US only) 14.4 229 The weather display The main features of the weather display are as follows: Range Animation time/data Signal strength 12:00 22/11 Medium 2400 nm Status bar Marine zone Surface observation stations Wave heights DISPLAY GRAPHICS... ANIMATE WEATHER... WEATHER REPORTS... PRESENTATION... Weather soft keys D8564_1 FIND SHIP 14.5 Moving around the weather map When you open the Weather application, a world map is displayed.
230 E Series Networked Display Reference Manual 14.7 Weather graphics This section summarizes the weather symbols used within the weather application. For details of each weather type, please refer to the appropriate section.
Chapter 14: Weather (US only) 231 Precipitation (NOWRad) NOWRad displays the type and level of precipitation: Color code Precipitation type Intensity Light green Rain ( 15-19 dBz ) Medium green Rain ( 20-29 dBz ) Dark green Rain ( 30-39 dBz ) Yellow Rain ( 40-44 dBz ) Orange Rain ( 45-49 dBz ) Light red Rain ( 50-54 dBz ) Dark red Rain ( 55 + dBz) Light Blue Snow ( 5-19 dBz ) Dark blue Snow ( 20 + dBz ) Light pink Mixed ( 5-19 dBz ) Dark pink Mixed ( 20 + dBz ) D 8569_
232 E Series Networked Display Reference Manual Sea surface temperature (SST) The temperature range of the sea surface is indicated by shading. This shading ranges through blue/green/yellow/ orange/red. D8570_1 For details of how to view the sea surface temperature at a specific point, see page 236. Canadian radar Canadian radar shows the intensity of precipitation for Canada. Unlike NOWRad, Canadian radar does not show the precipitation type.
Chapter 14: Weather (US only) 233 Tropical storm data Tropical storm data can be displayed for a selected storm. This includes: • The storm’s name, type, date and time. • The position, direction and speed of travel of the storm. • The pressure and maximum wind speed and gusts. To display tropical storm data: Tropical Storm Data Storm name EPSILON Storm ID AL292005 Hurricane Category 2 OBJECT INFO OK Hurricane Category 2 OK for more info Direction Speed 075oT Max Wind Speed 64.9kt 80.