Owners Manual www.adjustablesbyleggett.
CONTENTS Advisory................................................................................................................................. 4 Acoustics............................................................................................................................... 6 Installation.............................................................................................................................. 7 Prodigy™ Hand Control Function.....................................................
advisory important information READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT This Prodigy™ adjustable bed has been quality engineered with design features to assure comfort and safety when operated properly. electrical grounding This product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.
ADVISORY important information READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT This Prodigy™ adjustable bed has been quality engineered with design features to assure comfort and safety when operated properly. HOSPITAL use DISCLAIMER This bed is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this bed with tent type oxygen therapy equipment, or use near explosive gases.
acoustics lifting/lowering mechanisms The lift/lower feature will emit a minimal humming sound during operation. This is normal. During operation, the lift arm wheels make contact with the platform support of the bed. This applies slight tension on the moving components and resonance is reduced to a minimum level. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the bed with the hand control.
installation For installation and setup, complete the numbered procedure indicated below and on the following pages: 1.
installation 2. Carefully lift the bed base frame from the shipping carton, keeping the unit topside-down. 3. Install (4) legs into the base frame. Simply screw each leg into a tapped hole at each corner of the base frame (figure 1). Insert casters into the bottom of each bed leg. casters – press-fit into bottom of legs legs – screw into tapped hole at each corner 7. Install batteries in hand control (4-AAA size, included).
installation b. Place mattress retainer ends into grommeted holes in top surface of adjustable bed base (figureS 3 and 4). Note: king size will use only (2) side retainers around outside perimeter. 10. Install headboard brackets to the bed base frame. When attaching (2) twin size units to a king size headboard an optional swing hinge kit (see accessory section) may be used to connect the twin units.
installation 11. Install headboard brackets to the bed base frame per the following instructions: a. Raise the head section of the bed (with hand control) to gain access to the bed base frame. b. Slide one headboard bracket channel onto one side of the bed base frame. Using (2) carriage bolts/nuts (figure 6) attach channel to base frame (figure 7). Hand tighten bolts/ nuts (loosely) to allow adjustment of the headboard bracket channels.
installation d. Slide headboard bracket assemblies (in or out) to achieve a distance of 1.5 inches (38.1mm) to 2 inches hes nc i 2 (50.8mm) between the edge of the to 1.5 bed base and headboard bracket flange assemblies (figure 9). e. Firmly tighten the 3 inch carriage bolts of both headboard bracket channels. f. Measure the distance (center-tocenter) between the mounting holes T in the headboard. CKE R BRA S IN O E D g.
Prodigy™ hand control function set Button Press to capture any position or function (massage or wave) of the bed as a programmed position. To program, press the S button. When the display shows Set, within 2 seconds press the 1, 2, 3, or 4 button to save the current setting. when programmed, position 1 is the default sleep position and postion 3 is the default anti-snore position.Up to four positions may be saved. display Indicates current time when no features are being activated.
troubleshooting In the event the Prodigy™ adjustable bed fails to operate, investigate the symptoms and possible solutions provided in the chart below: symptom Hand control illuminates and appears to be operable, but will not activate bed. solution • Verify power cord is plugged into a working, grounded electrical outlet. A grounded, electrical surge protection device is recommended. Test outlet by plugging in another working appliance.
accessories Prodigy™ optional equipment Contact customer service toll free (800-888-3078) to order the accessories indicated in the chart below.
1-2-lifetime warranty Leggett & Platt, Incorporated (“L&P”) warrants this adjustable bed to the consumer who is the original purchaser (the “purchaser”), subject to the terms and conditions set forth herein. This warranty begins on the “warranty commencement date” which is the date of purchase for new unused beds and the date of manufacture for beds that have been used as floor or display models. Thus, on a floor model bed, the warranty is a portion of the limited lifetime warranty.
1-2-lifetime warranty Repairs to or replacement of an adjustable bed or its components under the terms of this limited warranty will apply to the original warranty period and will not serve to extend such period. The decision to repair or to replace defective parts under this warranty shall be made, or cause to be made, by L&P at its option and in its sole discretion. Repair or replacement shall be the sole remedy of the purchaser.