MSDS

ManualsBrandsRapid Set ManualsBuilding materials2.12 oz. Concrete Pharmacy Flow Control

Rapid Set FLOW Control

Version #: 02 Revision date: - Issue date: 10-March-2015

SDS US

1 / 8

SAFETY DATA

SHEET

1. Identification

Product identifier Rapid Set FLOW Control

Other means of identification

Product code

802010010, 802040035, 802100000

Recommended use

Industrial use.

Recommended restrictions

Workers (and your customers or users in the case of resale) should be informed of the potential

presence of respirable dust. Appropriate training in the proper use and handling of this material

should be provided as required under applicable regulations.

Manufacturer/Importer/Supplier/Distributor information

Company name

CTS Cement Manufacturing Corporation

Address

11065 Knott Ave Suite A

Cypress, CA 90630

United States

Telephone

1-800-929-3030

E-mail

info@ctscement.com

Contact person

Safety Officer

Emergency telephone

number

2. Hazard(s) identification

Physical hazards

Health Hazards

OSHA defined hazards

Label elements

1-800-929-3030 (8 AM - 5 PM)

Not classified.

Skin corrosion/irritation

Serious eye damage/eye irritation

Carcinogenicity

Specific Target Organ Toxicity, Single

Exposure

Specific Target Organ Toxicity, Repeated

Exposure

Chronic target organ effects reported.

Category 2

Category 1

Category 1A

Category 3 respiratory tract irritation

Category 2 (Lungs)

Signal word

Danger

Hazard statement Contains material which can cause cancer. Can form explosive dust air mixtures. Avoid creating

dust. May cause sensitization by skin contact.

May cause respiratory irritation. Avoid inhalation

of dust. Avoid ingestion. Avoid contact with skin, eyes and clothing.

Precautionary statement

Prevention

Obtain special instructions before use. Do not handle until all safety precautions have been read

and understood. Do not breathe dust. Wash thoroughly after handling. Use in a well-ventilated

area. Wear protective gloves/protective clothing/eye protection/face protection.

Response

If exposed or concerned: Get medical advice/attention. If in eyes: Rinse cautiously with water for

several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately

call a poison center/doctor. If on skin: Wash with plenty of water. If skin irritation occurs: Get

medical advice/attention. Take off contaminated clothing and wash before reuse. If inhaled:

Remove person to fresh air and keep comfortable for breathing. Call a poison center/doctor if you

feel unwell.

Storage

Keep container tightly closed. Store in dry location.

Summary of content (8 pages)

PAGE 1
SAFETY DATA SHEET 1. Identification Product identifier Rapid Set FLOW Control Other means of identification Product code 802010010, 802040035, 802100000 Recommended use Industrial use. Recommended restrictions Workers (and your customers or users in the case of resale) should be informed of the potential presence of respirable dust. Appropriate training in the proper use and handling of this material should be provided as required under applicable regulations.
PAGE 2
Disposal Hazard(s) not otherwise classified (HNOC) Dispose of contents/container in accordance with local/regional/national/international regulations. None known. 3. Composition/information on ingredients Mixtures Chemical name CAS number Proprietary Compound 99-99.9 50-00-0 Methanal Composition comments % < 0.1 All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume. 4.
PAGE 3
6. Accidental release measures Personal precautions, protective equipment and emergency procedures Methods and materials for containment and cleaning up Environmental precautions Avoid dust formation. Avoid inhalation of dust. Avoid skin contact. Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up.
PAGE 4
Appropriate engineering controls Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.
PAGE 5
Partition coefficient (oil/water) Not applicable. VOC (Weight %) Not tested. 10. Stability and reactivity Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport. Chemical stability Possibility of hazardous reactions Material is stable under normal conditions. Conditions to avoid Avoid temperatures exceeding the decomposition temperature. Contact with incompatible materials. Avoid dispersal of dust in the air (i.e.
PAGE 6
Reproductive toxicity The results of animal studies gave no indication of a fertility impairing effect. Specific target organ toxicity single exposure May cause respiratory irritation. Specific target organ toxicity repeated exposure May cause damage to organs (Lungs) through prolonged or repeated exposure. Aspiration hazard Due to the physical form of the product it is not an aspiration hazard. Chronic effects Prolonged or repeated exposure may cause lung injury.
PAGE 7
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not listed. CERCLA Hazardous Substance List (40 CFR 302.4) Not listed.
PAGE 8
International Inventories Country(s) or region United States & Puerto Rico Inventory name Toxic Substances Control Act (TSCA) Inventory On inventory (yes/no)* Yes *A "Yes" indicates this product complies with the inventory requirements administered by the governing country(s). A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s). 16.