ACTIVE 8 2 0 10 0 10 8 2 10 6 0 ACTIVE Z1 Z2 Z1 Z2 RMT BOTH RMT BOTH 2 6 4 4 6 4 8 2 0 4 10 6 LINE 2 8 2 0 4 10 6 LINE 3 8 2 0 4 10 6 PRIORITY PROGRAM INPUT LEVELS LINE 1 LEVEL ZONE 1 ZONE 2 PAGING ZONE ASSIGN PAGE 1 PAGE 2 8 OFF ON DUCKER DEPTH L1 L2 L3 P 2 4 10 6 LEVEL RMT SIG OL ZONE 1 PROGRAM SELECT 8 OFF ON DUCKER DEPTH L1 L2 L3 P 2 4 10 6 LEVEL RMT SIG OL ZONE 2 PROGRAM SELECT 8 100 630 1.
IMPORTANT SAFETY INSTRUCTIONS For the continued safety of yourself and others we recommend that you read the following safety and installation instructions. Keep this document in a safe location for future reference. Please heed all warnings and follow all instructions. Do not use this equipment in a location where it might become wet. Clean only with a damp cloth. This equipment may be installed in an industry standard equipment rack.
OPERATORS MANUAL CP 64 COMMERCIAL PROCESSOR PROGRAM INPUT LEVELS PAGING ZONE ASSIGN PAGE 1 PAGE 2 Z1 Z2 Z1 Z2 RMT BOTH RMT BOTH 2 LEVEL ZONE 1 ZONE 2 4 6 10 LINE 1 LINE 2 LINE 3 4 4 4 6 0 10 6 0 10 0 10 ZONE 1 PRIORITY 4 6 0 10 DUCKER DEPTH 6 8 2 8 2 8 2 8 2 8 2 0 ACTIVE 4 6 L1 8 0 10 OFF ZONE 2 PROGRAM SELECT L2 L3 P LEVEL 4 2 ON ACTIVE DUCKER DEPTH 6 PROGRAM SELECT L1 8 10 OFF RMT SIG OL L2 L3 P + LEVEL 4 ON 8 10 RMT SIG OL 100 ZONE 1 250 630
CP 64 FRONT PANEL 1 6 PROGRAM INPUT LEVELS PAGING ZONE ASSIGN PAGE 1 PAGE 2 LEVEL ZONE 1 ZONE 2 4 Z1 Z2 Z1 Z2 RMT BOTH RMT BOTH 2 0 ACTIVE 2 8 4 6 4 6 0 10 LINE 2 4 6 0 10 LINE 3 4 6 0 4 10 DUCKER DEPTH 6 8 2 0 10 ZONE 1 PRIORITY 6 8 2 8 2 8 2 8 2 10 LINE 1 10 OFF ZONE 2 PROGRAM SELECT L1 8 0 10 L2 L3 P LEVEL 4 6 2 ON OFF 4 5 7 L2 L3 P + LEVEL 4 40 100 ZONE 1 250 630 1.6k 4k 10k 40 100 ZONE 2 250 630 1.
CP 64 REAR PANEL 5 1 6 REMOTES POWER ZONE 2 D1 D0 MIN D1 D0 MIN ZONE 2 OUT +8 ZONE 1 OUT RIGHT LEFT +8 + + – – 750mA CLASS 2 EQUIPMENT 2 20 – – + + – LIMIT D1 D0 Vc2 Vr2 D1 D0 3 PAGING INPUTS OUTPUTS ZONE 1 Vc1 Vr1 + – LIMIT + 4 + 20 – – + EXPAND 2 OUT ZONE PAGE 2 13 12 + PRIORITY ASSIGN OFF Z1 ZONE PAGE Z2 1 – – + BOTH PROGRAM – – 7 + 8 CP 64 L RMT ZONE ASSIGN PAGE 2 PAGE 1 RANE CORP. MADE IN U.S.A.
INTERNAL ADJUSTMENTS There are a number of controls inside the CP 64 used to configure the system for specific applications. Access to these controls is only required during initial system setup. Set up all internal controls before the CP 64 is installed in a rack or wired into a system. Make sure the power is off before removing the top cover to gain access. Refer to the diagram below for control locations.
by the ZONE LEVEL control. Note the following: • Zone Level, EQ and Limiter circuits do not affect Page signals summed Post-VCA. • Zone Level, EQ and Limiter circuits do affect Page signals summed Pre-VCA. • Page signals are not available on the Expand Zone output when summed Post-VCA. • Page signals are always available for the Expand Page output.
REMOTE MOUNTING The ZR 1 and PR 2 remote assemblies mount in a standard U.S. electrical box with a minimum depth of 2.25". Be sure to note the wire color of each input in order to facilitate correct wiring to the CP 64. Connect each wire to the 5-pin connector by fully inserting it in the correct socket and tightening the screw. Make sure wires are free of nicks and that the cable jacket is stripped back sufficiently to allow it to lie in the electrical box with the remote assembly inserted.
RECOMMENDED CALIBRATION PROCEDURE The CP 64 is a very versatile instrument. While this allows it to conform to the requirements of a large number of system applications, it also results in complexity. For this reason, it is very important to use an organized approach to system calibration. Once the internal switches are set and the system is connected, take the time for proper calibration.
…CP 64 Calibration (continued) 1. Connect the Power Supply and verify the Power indicator lights. 2. Verify Zone Level controls are set to Maximum and that you have an active source for each of the Program Inputs you intend to use. Select each Program Input and adjust its Input Level control to be the very loudest you would ever desire. 3. Adjust the rear panel Zone Limit thresholds so that they just start to audibly reduce the output level.