b Maintenance and Service Guide Compaq Presario V6000 Notebook PC Document Part Number: 416630-003 April 2007 This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures.
© Copyright 2006, 2007 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Intel, Core, and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries and regions. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
Safety warning notice Å WARNING: To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
Contents Contents 1 Product Description 1.1 1.2 1.3 1.4 1.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 Resetting the Computer. . . . . . . . . . . . . . . . . . . . . . . 1–4 Power management . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 External Components . . . . . . . . . . . . . . . . . . . . . . . . 1–6 Design overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–22 2 Troubleshooting 2.1 Setup Utility in Windows XP . . . . . . . . . . . .
Contents 3 Illustrated Parts Catalog 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . 3–1 Computer Major Components. . . . . . . . . . . . . . . . . . 3–2 Display Assembly Components . . . . . . . . . . . . . . . 3–21 Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . . 3–23 Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–25 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 5 Removal and Replacement Procedures 5.1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2 5.2 Disassembly Sequence Chart . . . . . . . . . . . . . . . . . . 5–3 5.3 Preparing the Computer For Disassembly . . . . . . . . 5–4 5.4 Hard Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6 5.5 Computer Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10 5.6 Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–11 5.
Contents 6 Specifications A Screw Listing B Backup and Recovery in Windows XP C Backup and Recovery in Windows Vista D Display Component Recycling E Connector Pin Assignments F Power Cord Set Requirements Index viii Maintenance and Service Guide
1 Product Description The Compaq Presario V6000 Notebook PC offers advanced modularity, Intel® Core™ Duo and Celeron® and AMD Turion™ 64 Mobile Technology and Mobile AMD Sempron™ processors, and extensive multimedia support.
Product Description 1.1 Features The following features vary by computer model: ■ Intel Core Duo T7200 (2.00-GHz) ■ Intel Core Duo T1350 (1.86-GHz) ■ Intel Core Duo T5600 (1.83-GHz) ■ Intel Core Duo T2350 (1.86-GHz) ■ Intel Core Duo T2250 (1.73-GHz) ■ Intel Core Duo T5500 (1.66-GHz) ■ Intel Core Duo T5200 (1.66-GHz) ■ Intel Core Duo T2060 (1.60-GHz) ■ Intel Core Duo T2050 (1.60-GHz) ■ Intel Celeron 440 (1.86-GHz) ■ Intel Celeron 430 (1.73-GHz) ■ Intel Celeron 420 (1.60-GHz) ■ AMD Turion ML-60 (2.
Product Description ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ TouchPad pointing device with on/off button and dedicated two-way scroll zone Integrated 10/100 BASE-T Ethernet local area network (LAN) network interface card (NIC) with RJ-45 jack Integrated high-speed 56K modem with RJ-11 jack Integrated wireless support for Mini Card IEEE 802.11b and 802.
Product Description 1.2 Resetting the Computer If the computer you are servicing has an unknown password, follow these steps to clear the password. These steps also clear CMOS: 1. Prepare the computer for disassembly (refer to Section 5.3, “Preparing the Computer For Disassembly,” for more information). 2. Remove the real-time clock (RTC) battery (refer to Section 5.7, “RTC Battery,” for more information). 3. Wait approximately 5 minutes. 4. Replace the RTC battery and reassemble the computer. 5.
Product Description 1.3 Power management The computer comes with power management features that extend battery operating time and conserve power.
Product Description 1.4 External Components The external components on the front of the computer are shown below and described in Table 1-1. Front Components Table 1-1 Front Components Item Component Function 1 Power light On: The computer is on. Blinking: The computer is in standby. Off: The computer is off or in hibernation. 2 Battery light On: A battery is charging. Blinking: A battery that is the only available power source has reached a low-battery condition.
Product Description Table 1-1 Front Components (Continued) Item Component Function 3 Drive light Blinks when the hard drive or optical drive is being accessed. 4 Wireless switch Turns the wireless feature on or off, but does not create a wireless connection. wireless network must be set up to ✎ Aestablish a wireless connection. 5 Wireless light Blue: An integrated wireless device, such as a wireless local area network (LAN) device and/or a Bluetooth® device, is turned on.
Product Description The external components on the left side of the computer are shown below and described in Table 1-2. Left-Side Components Table 1-2 Left-Side Components Item Component Function 1 S-Video-out jack Connects an optional S-Video device such as a television, VCR, camcorder, overhead projector, or video capture card. 2 External monitor port Connects an external VGA monitor or projector. 3 Expansion port 3 Connects the computer to an optional expansion product.
Product Description Table 1-2 Left-Side Components (Continued) Item Component Function 4 RJ-45 (network) jack Connects a network cable. 5 RJ-11 (modem) jack Connects a modem cable. 6 HDMI port (select models only) Connects an optional audio or video device, such as a high definition television, set-top box, DVD player, or any compatible digital or audio device. 7 USB ports (2) Connect optional USB devices.
Product Description The external components on the right side of the computer are shown below and described in Table 1-3.
Product Description Table 1-3 Right-Side Components Item Component Function 1 ExpressCard slot Supports optional ExpressCard/54 cards. 2 Optical drive Reads an optical disc. 3 USB port (select models only) Connects an optional USB device. 4 Power connector Connects an AC adapter. 5 Security cable slot Attaches an optional security cable to the computer. security cable is designed to act ✎ The as a deterrent, but it may not prevent the computer from being mishandled or stolen.
Product Description The computer keyboard components are shown below and described in Table 1-4.
Product Description Table 1-4 Keyboard Components Item Component Function 1 Function keys Execute frequently used system functions when pressed in combination with the fn key. 2 caps lock key Enables caps lock and turns on the caps lock light. 3 fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. 4 Windows logo key Displays the Microsoft Windows Start menu.
Product Description The computer top components are shown below and described in Table 1-5.
Product Description Table 1-5 Top Components, Part 1 Item Component Function 1 Internal microphones (2, select models only) Record sound. is a microphone icon next ✎ Iftothere each microphone opening, your computer has internal microphones. 2 Power button When the computer is ■ Off, press to turn on the computer. ■ On, press to enter hibernation. ■ In standby, briefly press to exit standby. ■ In hibernation, briefly press to exit hibernation.
Product Description The computer top components are shown below and described in Table 1-6.
Product Description Table 1-6 Top Components, Part 2 Item Component Function 1 Media button If QuickPlay is not installed and the computer is ■ On, opens the music program or Media menu, which allows you to select a multimedia program. ■ Off, does not function. ■ In standby, resumes from standby into Windows. If QuickPlay is installed and the computer is ■ On, opens the music program or Media menu, which allows you to select a multimedia program.
Product Description The computer TouchPad components are shown below and described in Table 1-7.
Product Description Table 1-7 Touchpad Components Item Component Function 1 TouchPad light Blue: TouchPad is enabled. Amber: TouchPad is disabled. 2 TouchPad Moves the pointer and selects or activates items on the screen. 3 TouchPad horizontal scroll zone Allows you to scroll left or right. 4 Left and right TouchPad buttons Function like the left and right buttons on an external mouse. 5 TouchPad on/off button Enables/disables the TouchPad.
Product Description The external components on the bottom of the computer are shown below and described in Table 1-8. Bottom Components Table 1-8 Bottom Components Item Component Function 1 Battery bay Holds the battery. 2 Battery release latch Releases the battery from the battery bay. 3 Optical drive Reads an optical disc.
Product Description Table 1-8 Bottom Components (Continued) Item Component Function 4 Memory module compartment Contains the memory module slots, the Mini Card WLAN slot, and the RTC battery. 5 Vents (5) Enable airflow to cool internal components. computer fan starts up ✎ The automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. 6 Hard drive bay Maintenance and Service Guide Holds the hard drive.
Product Description 1.5 Design overview This section presents a design overview of key parts and features of the computer. Refer to Chapter 3, “Illustrated Parts Catalog,” to identify replacement parts, and Chapter 5, “Removal and Replacement Procedures,” for disassembly steps.
2 Troubleshooting Å WARNING: Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board. Improper repairs can create a safety hazard.
Troubleshooting 1. To open the Setup Utility, turn on or restart the computer in Windows, and then press f10 while the prompt, “Press to enter setup,” is displayed in the lower-left corner of the screen. 2. Use the arrow keys to select System Configuration > Language, and then press enter. 3. Press f5 or f6 (or use the arrow keys) to select a language, and then press enter to select a language. 4.
Troubleshooting 1. To start the Setup Utility, turn on or restart the computer in Windows, and then press f10 while the prompt, “Press to enter setup,” is displayed in the lower-left corner of the screen. 2. Access the system information by using the Main menu. 3. To close the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding Changes, and then press enter. (The computer restarts in Windows.
Troubleshooting Using Advanced Setup Utility Features This guide describes the Setup Utility features recommended for all users. For more information about the Setup Utility features recommended for advanced users only, refer to the Help and Support Center, which is accessible only when the computer is in Windows. The Setup Utility features available for advanced users include a hard drive self-test, a Network Service Boot, and settings for boot order preferences.
Troubleshooting ■ To close the Setup Utility without saving your changes from the current session: If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Discarding Changes, and then press enter. After the Setup Utility closes, the computer restarts in Windows. Setup Utility Menus The menu tables in this section provide an overview of Setup Utility options.
Troubleshooting Security Menu Table 2-2 Security Menu Select To Do This Administrator password Enter, change, or delete an administrator password. Power-on password Enter, change, or delete a power-on password. System Configuration Menu Table 2-3 System Configuration Menu Select To Do This Language Support Change the Setup Utility language. Embedded WLAN Device Radio Enable/disable an embedded wireless LAN device.
Troubleshooting Table 2-3 System Configuration Menu (Continued) Select To Do This Boot Options Set the following boot options: f10 and f12 Delay (sec.)—Set the delay for the f10 and f12 functions of the Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20). ■ CD-ROM boot—Enable/disable boot from CD-ROM. ■ Floppy boot—Enable/disable boot from Floppy. ■ Internal Network Adapter boot—Enable/disable boot from Internal Network Adapter.
Troubleshooting 2.2 Setup Utility in Windows Vista The Setup Utility is a ROM-based information and customization utility that can be used even when your Windows® operating system is not working or will not load. fingerprint reader (select models only) does not work ✎ The when accessing the Setup Utility. The utility reports information about the computer and provides settings for startup, security, and other preferences. To start the Setup Utility: 1. Turn on or restart the computer. 2.
Troubleshooting 5. To set your preferences and exit the Setup Utility, press f10 and then follow the instructions on the screen. Your preferences go into effect when the computer restarts in Windows. Navigating and Selecting in the Setup Utility Because the Setup Utility is not Windows-based, it does not support the TouchPad. Navigation and selection are by keystroke. ■ To choose a menu or a menu item, use the arrow keys.
Troubleshooting Restoring Default Settings in the Setup Utility The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is already running, begin at step 2. 1. To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press to enter setup” is displayed in the lower-left corner of the screen. 2. Select Exit > Load Setup Defaults, and then press enter. 3.
Troubleshooting The “Press to change boot order” message that is displayed in the lower-left corner of the screen each time the computer is started or restarted in Windows is the prompt to change the boot order. Closing the Setup Utility You can close the Setup Utility with or without saving changes. ■ To close the Setup Utility and save your changes from the current session, use either of the following procedures: ❏ Press f10, and then follow the instructions on the screen.
Troubleshooting Main Menu Table 2-1 Main Menu Select To Do This System Information ■ ■ ■ View and change the system time and date. View identification information about the computer. View specification information about the processor, memory size, system BIOS, and keyboard controller version (select models only). Security Menu Table 2-2 Security Menu Select To Do This Administrator password Enter, change, or delete an administrator password.
Troubleshooting Table 2-3 System Configuration Menu Select Boot Options To Do This Set the following boot options: f10 and f12 Delay (sec.)—Set the delay for the f10 and f12 functions of the Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20). ■ CD-ROM boot—Enable/disable boot from CD-ROM. ■ Floppy boot—Enable/disable boot from Floppy. ■ Internal Network Adapter boot—Enable/disable boot from Internal Network Adapter.
Troubleshooting Diagnostics Menu Table 2-4 Diagnostics Menu Select To Do This Hard Disk Self Test Run a comprehensive self-test on the hard drive. models with two hard drives, this menu ✎ On option is called the Primary Hard Disk Self Test. Secondary Hard Disk Self Test (select models only) 2–14 Run a comprehensive self-test on a secondary hard drive.
Troubleshooting 2.3 Troubleshooting Flowcharts Table 2-5 Troubleshooting Flowcharts Overview Flowchart Description 2.1 “Flowchart 2.1—Initial Troubleshooting” 2.2 “Flowchart 2.2—No Power, Part 1” 2.3 “Flowchart 2.3—No Power, Part 2” 2.4 “Flowchart 2.4—No Power, Part 3” 2.5 “Flowchart 2.5—No Power, Part 4” 2.6 “Flowchart 2.6—No Video, Part 1” 2.7 “Flowchart 2.7—No Video, Part 2” 2.8 “Flowchart 2.8—Nonfunctioning Docking Device (if applicable)” 2.9 “Flowchart 2.
Troubleshooting Table 2-5 Troubleshooting Flowcharts Overview (Continued) Flowchart Description 2.14 “Flowchart 2.14—No OS Loading, Optical Drive” 2.15 “Flowchart 2.15—No Audio, Part 1” 2.16 “Flowchart 2.16—No Audio, Part 2” 2.17 “Flowchart 2.17—Nonfunctioning Device” 2.18 “Flowchart 2.18—Nonfunctioning Keyboard” 2.19 “Flowchart 2.19—Nonfunctioning Pointing Device” 2.20 “Flowchart 2.
Troubleshooting Flowchart 2.1—Initial Troubleshooting Begin troubleshooting. N Go to Is there power? “Flowchart 2.2—No Power, Part 1.” Y N Check LED board, speaker connections. Beeps, LEDs, or error messages? N Y Go to All drives working? N Go to Is there video? (no boot) Y “Flowchart 2.6—No Video, Part 1.” N Keyboard/ pointing device working? Y N Go to Is the OS loading? N Go to Is there sound? Y “Flowchart 2.9—No Operating System (OS) Loading.” Y “Flowchart 2.15—No Audio, Part 1.
Troubleshooting Flowchart 2.2—No Power, Part 1 No power (power LED is off). Remove from docking device (if applicable). N N Power up on battery power? Go to Power up on battery power? Reset power.* “Flowchart 2.3—No Power, Part 2.” Y Y N N Power up on AC power? Power up on AC power? Reset power.* Go to “Flowchart 2.4—No Power, Part 3.” Y Y Y Power up in docking device? Done *NOTES 1. On select models, there is a separate reset button. 2.
Troubleshooting Flowchart 2.3—No Power, Part 2 Continued from “Flowchart 2.2—No Power, Part 1.” Visually check for debris in battery socket and clean if necessary. Y Power on? Done N Check battery by recharging it, moving it to another computer, or replacing it. N Replace power supply (if applicable). Power on? Y N Go to Done Power on? “Flowchart 2.4—No Power, Part 3.
Troubleshooting Flowchart 2.4—No Power, Part 3 Continued from “Flowchart 2.3—No Power, Part 2.” Plug directly into AC outlet. Y Power LED on? Done N Reseat AC adapter in computer and at power source. Y Power on? Done N External N Try different outlet. Power outlet active? Y Internal or external AC adapter? Replace external AC adapter. N Internal Go to “Flowchart 2.5—No Power, Part 4.” Replace power cord.
Troubleshooting Flowchart 2.5—No Power, Part 4 Continued from “Flowchart 2.4—No Power, Part 3.” Open computer. Y Loose or damaged parts? N Reseat loose components and boards and replace damaged items. Close computer and retest. N Power on? Y Done Replace the following items (if applicable). Check computer operation after each replacement: 1. Internal DC-DC converter* 2. Internal AC adapter 3. Processor board* 4.
Troubleshooting Flowchart 2.6—No Video, Part 1 No video. Docking Device Go to Stand-alone or docking device? *NOTE: To change from internal to external display, use the hotkey combination. “Flowchart 2.7—No Video, Part 2.” Stand-alone Internal or external display*? Y Adjust brightness. A Adjust brightness. Press lid switch to ensure operation. Y Video OK? Done N Internal External Video OK? Y Done N Video OK? Done N Replace the following one at a time. Test after each replacement. 1.
Troubleshooting Flowchart 2.7—No Video, Part 2 Continued from “Flowchart 2.6—No Video, Part 1.” Remove computer from docking device, if connected. Adjust display brightness. Check brightness of external monitor. N Y Go to “A” in “Flowchart 2.6—No Video, Part 1.” Video OK? Y Video OK? Done N Check that computer is properly seated in docking device, for bent pins on cable, and for monitor connection. Try another external monitor.
Troubleshooting Flowchart 2.8—Nonfunctioning Docking Device (if applicable) Nonfunctioning docking device. Reseat power cord in docking device and power outlet. Check voltage setting on docking device. Reinstall computer into docking device. Y Reset monitor cable connector at docking device. Docking device operating? N Y Docking device operating? N Done Done Test replacement docking device with new computer. Remove computer, replace docking device.
Troubleshooting Flowchart 2.9—No Operating System (OS) Loading No OS loading.* Reseat power cord in docking device and power outlet. No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” No OS loading from diskette drive, go to “Flowchart 2.13—No OS Loading, Diskette Drive.” No OS loading from optical drive, go to “Flowchart 2.14—No OS Loading, Optical Drive.” No OS loading from network, go to “Flowchart 2.20—No Network/Modem Connection.
Troubleshooting Flowchart 2.10—No OS Loading, Hard Drive, Part 1 OS not loading from hard drive. Y Nonsystem disk message? N Go to “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” Reseat external hard drive. Y OS loading? Done N N Boot from CD? N Y Boot from diskette? Check the Setup utility for correct booting order. Y Change boot priority through the Setup Utility and reboot. N Boot from hard drive? N Y Boot from hard drive? Done Y 2–26 Go to “Flowchart 2.
Troubleshooting Flowchart 2.11—No OS Loading, Hard Drive, Part 2 Continued from “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” Reseat hard drive. N 1. Replace hard drive. 2. Replace system board. Disc or diskette in drive? Y Y Hard drive accessible? Done N Remove disc or diskette and reboot. Run FDISK. Y Boot from hard drive? N Done N Hard drive partitioned? Y N Y N Go to “Flowchart 2.13—No OS Loading, Diskette Drive.
Troubleshooting Flowchart 2.12—No OS Loading, Hard Drive, Part 3 Continued from “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” N System files on hard drive? Install OS and reboot. Y Y Y Virus on hard drive? OS loading from hard drive? Clean virus. N Done N Y Run SCANDISK and check for bad sectors. Diagnostics on disc or diskette? Replace hard drive. N N Can bad sectors be fixed? Run diagnostics and follow recommendations. Replace hard drive. Y N Boot from hard drive? Fix bad sectors.
Troubleshooting Flowchart 2.13—No OS Loading, Diskette Drive Y OS not loading from diskette drive. Reseat diskette drive. OS loading? Done N Y N Bootable diskette in drive? Nonsystem disk message? N Y N Check diskette for system files. Try different diskette. Go to Boot from another device? “Flowchart 2.17—Nonfunctioning Device.” Y Y N Diskette drive enabled in the Setup utility? Nonsystem disk error? Enable drive and cold boot computer.
Troubleshooting Flowchart 2.14—No OS Loading, Optical Drive Y No OS loading from CD-ROM or DVD-ROM drive. N Install bootable disc and reboot computer. Bootable disc in drive? Disc in drive? Y N Install bootable disc. Try another bootable disc. Y Boots from CD or DVD? Done N Y Boots from CD or DVD? Reseat drive. Done N N Booting from another device? Y Y Booting order correct? N Go to “Flowchart 2.17—Nonfunctioning Device.” Reset the computer. Refer to Go to Section 1.
Troubleshooting Flowchart 2.15—No Audio, Part 1 Y Turn up audio internally or externally. No audio. Audio? Done N N Y Computer in docking device (if applicable)? Go to Internal audio? Undock N “Flowchart 2.16—No Audio, Part 2.” Y Go to Replace the docking device. “Flowchart 2.16—No Audio, Part 2.” Y Go to “Flowchart 2.17—Nonfunctioning Device.
Troubleshooting Flowchart 2.16—No Audio, Part 2 Continued from “Flowchart 2.15—No Audio, Part 1.” N Audio driver in OS configured? Reload audio drivers. Y N Correct drivers for application? Load drivers and set configuration in OS. Y Connect to external speaker. N Audio? Y Replace audio board and speaker connections in computer (if applicable).
Troubleshooting Flowchart 2.17—Nonfunctioning Device Nonfunctioning device. Reseat device. Unplug the nonfunctioning device from the computer and inspect cables and plugs for bent or broken pins or other damage. Y Clear CMOS. Fix or replace broken item. Any physical device detected? N Go to Reattach device. Close computer, plug in power, and reboot. “Flowchart 2.9—No Operating System (OS) Loading.” Replace hard drive. N Device boots properly? N Replace NIC.
Troubleshooting Flowchart 2.18—Nonfunctioning Keyboard Keyboard not operating properly. Connect computer to good external keyboard. N External device works? Replace system board. Y Reseat internal keyboard connector (if applicable). N Keyboard operating properly? Replace internal keyboard or cable. Y Y Keyboard operating properly? Done Done N Replace system board.
Troubleshooting Flowchart 2.19—Nonfunctioning Pointing Device Pointing device not operating properly. Connect computer to good external pointing device. N Replace system board. External device works? Y Reseat internal pointing device connector (if applicable). N Replace internal pointing device or cable. Pointing device operating properly? Y Y Pointing device operating properly? Done Done N Replace system board.
Troubleshooting Flowchart 2.20—No Network/Modem Connection No network or modem connection. N Replace jack or have jack activated. Network or modem jack active? Y Y Connect to nondigital line. Digital line? N Y N NIC/modem configured in OS? Network or modem connection working? Reload drivers and reconfigure. Done N Y Disconnect all power from the computer and open. Replace NIC/modem (if applicable). Reseat NIC/modem (if applicable).
3 Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers and option part numbers. 3.1 Serial Number Location When ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components Spare Part Number Item Description 1 Display assemblies (include wireless antenna transceivers and cables) For use with full-featured computer models (includes microphones) 15.4-inch, WXGA, TFT with BrightView 15.4-inch, WXGA, TFT Antiglare 432304-001 432305-001 For use with defeatured computer models (does not include microphones) 15.4-inch, WXGA, TFT with BrightView 15.
Illustrated Parts Catalog Computer Major Components 3–4 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 4 Keyboards (Continued) For use only with computer models using Intel processors in the following countries or regions: Latin America Saudi Arabia 441428-161 441428-171 Taiwan Thailand 441428-AB1 441428-281 For use only with computer models using AMD processors in the following countries or regions: Denmark, Finland, Norway, and Sweden 441428-DH1 Korea For UK OTC ID only 5 7
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item 8a 8b 8c 9 Description Spare Part Number Plastics Kit 438469-001 Includes: ExpressCard slot bezel Hard drive cover (includes 2 captive screws, secured by C-clips) Memory module compartment cover (includes 3 captive screws, secured by C-clips) Processors (include thermal pad) Intel Core Duo T7200 (2.00-GHz) Intel Core Duo T1350 (1.86-GHz) Intel Core Duo T5600 (1.83-GHz) Intel Core Duo T2350 (1.
Illustrated Parts Catalog Computer Major Components Maintenance and Service Guide 3–7
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item 10 11 Spare Part Number Description Bluetooth module (includes Bluetooth module cable) System boards 945GM, for use only with full-featured computer models using Intel processors 940GML, for use only with defeatured computer models using Intel processors 943GM - for use only with defeatured models 945PM - for Germany only For use only with full-featured computer models using AMD processors For use only with defeat
Illustrated Parts Catalog Computer Major Components Maintenance and Service Guide 3–9
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 15 Base enclosures (include wireless switch) For use with full-featured computer models For use with defeatured computer models 16 Optical drives (include bezel) DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe DVD±RW/R and CD-RW Double-Layer Combo Drive DVD/CD-RW Combo Drive 17 431427-001 438316-001 431413-001 431412-001 431411-001 Hard drives (all 5400-rpm, inclu
Illustrated Parts Catalog Computer Major Components Maintenance and Service Guide 3–11
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 18 Mini Card modules 802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the countries or regions listed below. These countries or regions are categorized as most of the world 1 (MOW1).
Illustrated Parts Catalog Computer Major Components Maintenance and Service Guide 3–13
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 18 Mini Card modules (Continued) 3–14 802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the countries or regions listed below. These countries or regions are categorized as the rest of the world (ROW). 407674-003 China Ecuador Haiti Uruguay Venezuela Honduras Pakistan Peru Qatar South Korea 802.
Illustrated Parts Catalog Computer Major Components Maintenance and Service Guide 3–15
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 18 Mini Card modules (Continued) 802.
Illustrated Parts Catalog Computer Major Components Maintenance and Service Guide 3–17
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 18 Mini Card modules (Continued) 3–18 802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the ROW countries or regions listed below: 407160-002 China Ecuador Haiti Uruguay Venezuela Honduras Pakistan Peru Qatar South Korea 802.
Illustrated Parts Catalog Computer Major Components Maintenance and Service Guide 3–19
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Spare Part Number Item Description 18 Mini Card modules (Continued) 802.11b/g WLAN Mini Card module for use with all computer models in the ROW countries or regions listed below: 407159-002 China Ecuador Haiti Uruguay Venezuela Honduras Pakistan Peru Qatar South Korea 802.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-2 Display Assembly Components Spare Part Number Information (Continued) Spare Part Number Item Description 3 Display Hinge Kit (includes left and right display hinges) 4 Display panels 433288-001 15.4-inch, WXGA, SVA display panel with BrightView 15.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-3 Mass Storage Devices Spare Part Number Information Spare Part Number Item Description 1 Hard drives (all 5400-rpm, include bracket and connector) For use with all computer models 2 200-GB (4200-rpm) 160-GB (5400-rpm) 120-GB 100-GB 80-GB 60-GB 441424-001 438485-001 431407-001 431406-001 431405-001 431404-001 40-GB hard drive for use only with computer models using Intel processors 434743-001 40-GB hard drive for use only with computer models using AMD processors
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-4 Plastics Kit Spare Part Number Information Item 1 2 3 3–26 Description Spare Part Number Plastics Kit 438669-001 Includes: ExpressCard slot bezel Hard drive cover (includes 2 captive screws, secured by C-clips) Memory module compartment cover (includes 3 captive screws, secured by C-clips) Maintenance and Service Guide
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-5 Spare Parts: Miscellaneous (Continued) Description Spare Part Number Antenna adapter - DVB-T 412176-001 Carrying case 418162-001 Wired optical mouse 436238-001 Power cords For use with all computer models in the following countries or regions:: Australia and New Zealand 394279-011 Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and Sweden 394279-021 Canada, French Canada, Latin America, Thailand, and the United Sta
Illustrated Parts Catalog Table 3-5 Spare Parts: Miscellaneous (Continued) Spare Part Number Description Screw Kits (include the screws listed below; refer to Appendix A, “Screw Listing,” for more information on screw specifications and usage) For use only with computer models using Intel processors 434983-001 For use only with computer models using AMD processors 431433-001 ■ ■ ■ ■ ■ Phillips PM3.0×3.0 screw Phillips PM2.5×10.0 screw Phillips PM2.5×7.0 screw Phillips PM2.5×5.0 screw Phillips PM2.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 405527-001 Backpack 407159-001 802.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 407159-291 802.11b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan 407160-001 802.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number 407160-002 Description 802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the ROW countries or regions listed below: China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea 407313-001 HP Remote Control 407674-001 802.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number 407674-002 Description 802.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 407674-004 802.11b/g WLAN Mini Card module for use in Costa Rica, Israel, Kuwait, Thailand, UAE, Ukraine. 407674-291 802.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) 431372-001 AMD Turion ML-52 1.60-GHz processor (includes thermal pad) 431373-001 AMD Turion ML-56 1.80-GHz processor (includes thermal pad) 431374-001 Mobile AMD Sempron 3200+ 1.60-GHz processor (includes thermal pad) 431375-001 Mobile AMD Sempron 3400+ 1.80-GHz processor (includes thermal pad) 431386-001 15.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 431407-001 120-GB hard drive (5400-rpm, includes bracket and connector) 431411-001 DVD/CD-RW Combo Drive 431412-001 DVD±RW/R and CD-RW Double-Layer Combo Drive 431413-001 DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe 431424-001 Switch cover for use with defeatured computer models (includes LED board and LED board cable) 431425-001 Switch cover for use with fu
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 431444-001 Audio board for use with defeatured computer models (does not include infrared lens) 431445-001 USB/power connector board for use with 65W AC adapters (includes USB/power connector board cable) 431446-001 USB/power connector board for use with 90W AC adapters (includes USB/power connector board cable) 431450-001 Fan/heat sink assembly for use only with computer model
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 433283-001 Display bezel for use with full-featured computer models (includes microphone openings) 433284-001 Display bezel for use with defeatured computer models (does not include microphone openings) 433287-001 Display Cable Kit 433288-001 Display Hinge Kit (includes left and right display hinges) 434414-001 Mobile AMD Sempron 3500+ 1.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 434983-001 Screw Kit for use only with computer models using Intel processors 434984-001 Cable Kit 435743-001 HP Remote Control Ii Plus 435836-001 USB travel mouse 436156-001 Hard Drive Bracket Kit 436157-001 Intel Core Duo T5500 (1.66-GHz) processor 436159-001 Intel Celeron 430 (1.73-GHz) processor 436238-001 Wired optical mouse 436257-001 AMD Turion ML-60 2.
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 439254-001 Remote control - ExpressCard (EMEA) 441424-001 200-GB hard drive (4200-rpm, includes bracket & connector) 441428-001 Keyboard for use in the United States 441428-031 Keyboard for use in the United Kingdom 441428-051 Keyboard for use in France 441428-061 Keyboard for use in Italy 441428-071 Keyboard for use in Spain 441428-121 Keyboard for use in French Canada
Illustrated Parts Catalog Table 3-6 Spare Parts: Sequential Part Number Listing (Continued) 441762-001 Intel Core Duo T2350 (1.60-GHz) processor, for use with V6200 models 441763-001 Intel Core Duo T2060 (1.
4 Removal and Replacement Preliminaries This chapter provides essential information for proper and safe removal and replacement service. 4.
Removal and Replacement Preliminaries 4.2 Service Considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures. you remove each subassembly from the computer, place ✎ As the subassembly (and all accompanying screws) away from the work area to prevent damage. Plastic Parts Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts.
Removal and Replacement Preliminaries 4.3 Preventing Damage to Removable Drives Removable drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a removable drive, or loss of information, observe the following precautions: ■ Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system.
Removal and Replacement Preliminaries 4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.
Removal and Replacement Preliminaries 4.5 Packaging and Transporting Precautions Use the following grounding precautions when packaging and transporting equipment: ■ To avoid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes. ■ Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers or packaging. ■ Keep electrostatic-sensitive parts in their containers until the parts arrive at static-free workstations.
Removal and Replacement Preliminaries 4.6 Workstation Precautions Use the following grounding precautions at workstations: ■ Cover the workstation with approved static-shielding material (refer to Table 4-2, “Static-Shielding Materials”). ■ Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. ■ Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
Removal and Replacement Preliminaries 4.7 Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
5 Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are as many as 84 screws, in 9 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement. Refer to Appendix A, “Screw Listing,” for detailed information on screw sizes, locations, and usage.
Removal and Replacement Procedures 5.1 Serial Number Report the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer.
Removal and Replacement Procedures 5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing computer components. Disassembly Sequence Chart Section Description 5.3 Preparing the Computer For Disassembly # of Screws Removed Battery 0 5.4 Hard Drive 2 loosened to remove the hard drive cover 6 removed to disassemble the hard drive 5.5 Computer Feet 0 5.6 Memory Module 3 loosened to remove the memory module compartment cover 5.
Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section Description # of Screws Removed 5.12 Power Button Board 1 5.13 Display Assembly Display bezel Display inverter Display panel Display hinges Wireless antenna transceivers Microphones 4 8 0 4 4 2 2 5.14 Top Cover 22 5.15 Audio Board 2 5.16 Bluetooth Module 2 5.17 ExpressCard Assembly 4 5.18 USB/Power Connector Board 2 5.19 System Board 2 5.20 Fan/Heat Sink Assembly 4 5.21 Processor 1 loosened 5.
Removal and Replacement Procedures Battery Spare Part Number Information 12-cell, 8.8-Ahr 6-cell, 4.0-Ahr 432307-001 432306-001 4. Remove the battery by following these steps: a. Turn the computer upside down with the front panel toward you. b. Slide and hold the battery release latch 1 to the left. (The front edge of the battery disengages from the computer.) c. Lift the front edge of the battery 2 and swing it back. d. Remove the battery.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures 1. Prepare the computer for disassembly (refer to Section 5.3). 2. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the hard drive cover to the computer. 3. Lift the right side of the cover 2 and swing it to the left. 4. Remove the hard drive cover. hard drive cover is included in the Plastics Kit, spare part ✎ The number 438669-001.
Removal and Replacement Procedures 5. Use the mylar tab 1 to lift the hard drive 2 until it disconnects from the computer. 6. Remove the hard drive from the hard drive bay.
Removal and Replacement Procedures 7. Remove the six Phillips PM3.0×3.0 screws 1 that secure the hard drive bracket to the hard drive. 8. Lift the bracket 2 straight up to remove if from the hard drive. Removing the Hard Drive Bracket Reverse the above procedure to install and reassemble the hard drive.
Removal and Replacement Procedures 5.5 Computer Feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare part number 431431-001. The feet attach to the base enclosure in the locations illustrated below.
Removal and Replacement Procedures 5.6 Memory Module Memory Module Spare Part Number Information For use only with computer models using Intel processors 1024-MB 512-MB 256-MB 434742-001 434741-001 434740-001 For use only with computer models using AMD processors 1024-MB 512-MB 256-MB 431403-001 431402-001 431401-001 1. Prepare the computer for disassembly (refer to Section 5.3).
Removal and Replacement Procedures 2. Loosen the three Phillips PM2.0×5.0 screws 1 that secure the memory module compartment cover to the computer. 3. Lift the left side of the memory module compartment cover 2, and then swing it to the right. 4. Remove the memory module compartment cover. memory module compartment cover is included in the ✎ The Plastics Kit, spare part number 431429-001.
Removal and Replacement Procedures 5. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the module opposite the socket rises away from the computer.) 6. Slide the module 2 away from the socket at an angle. modules are designed with a notch 3 to prevent ✎ Memory incorrect installation into the memory module socket. Removing a Memory Module Reverse the above procedure to install a memory module.
Removal and Replacement Procedures 5.7 RTC Battery RTC Battery Spare Part Number Information RTC battery (includes 2-sided tape) 431436-001 1. Prepare the computer for disassembly (refer to Section 5.3). 2. Remove the memory module compartment cover (Section 5.6). 3. Disconnect the RTC battery cable 1 from the system board. 4. Remove the RTC battery 2. RTC battery is secured to the computer by 2-sided ✎ The tape. All replacement RTC battery spare part kits include 2-sided tape.
Removal and Replacement Procedures 5.8 Mini Card Module Mini Card Module Spare Part Number Information For use only with computer models using Intel processors 802.
Removal and Replacement Procedures Mini Card Module Spare Part Number Information (Continued) 802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the ROW countries or regions listed below: China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea 407674-003 Uruguay Venezuela 802.11b/g WLAN Mini Card module for use in Costa Rica, Israel, Kuwait, Thailand, UAE, Ukraine. 407674-004 802.
Removal and Replacement Procedures Mini Card Module Spare Part Number Information (Continued) 802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the ROW countries or regions listed below: 407160-002 China Ecuador Haiti Uruguay Venezuela Honduras Pakistan Peru Qatar South Korea 802.
Removal and Replacement Procedures Mini Card Module Spare Part Number Information (Continued) 802.11b/g WLAN Mini Card module for use with all computer models in the ROW countries or regions listed below: 407159-002 China Ecuador Haiti Uruguay Venezuela Honduras Pakistan Peru Qatar South Korea 802.11b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan 407159-291 1. Prepare the computer for disassembly (Section 5.3). 2.
Removal and Replacement Procedures 3. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card module before disconnecting the cables. Then disconnect the cables 1 from the module. 4. Remove the two Phillips PM2.0×3.0 screws 2 that secure the Mini Card module to the computer. (The edge of the module opposite the socket rises away from the computer). 5. Remove the module 3 by pulling it away from the socket at an angle.
Removal and Replacement Procedures 5.9 Optical Drive Optical Drive Spare Part Number Information DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe DVD±RW/R and CD-RW Double-Layer Combo Drive DVD/CD-RW Combo Drive 431413-001 431412-001 431411-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the Phillips PM2.5×7.0 screw 1 that secures the optical drive to the computer. 3. Insert a thin tool, such as a paper clip 2, into the media tray release hole.
Removal and Replacement Procedures 6. Position the optical drive with the optical drive bracket toward you. 7. Remove the two Phillips PM2.0×3.0 screws 1 that secure the optical drive bracket to the optical drive. 8. Remove the optical drive 2. Removing the Optical Drive Bracket Reverse the above procedure to reassemble and install the optical drive.
Removal and Replacement Procedures 5.10 Switch Cover Switch Cover Spare Part Number Information For use with full-featured computer models For use with defeatured computer models 431424-001 431425-001 1. Prepare the computer for disassembly (Section 5.3). 2. Close the computer. 3. Turn the computer upside down with the front panel toward you. 4. Remove the two Phillips PM2.5×10.0 screws that secure the switch cover to the computer.
Removal and Replacement Procedures 5. Turn the computer display-side up with the front toward you. 6. Open the computer as far as possible. 7. Lift the rear edge of the switch cover and swing it forward until it rests on the keyboard.
Removal and Replacement Procedures 8. Release the zero insertion force (ZIF) connector 1 to which the LED board cable is connected and disconnect the cable 2 from the LED board. 9. If it is necessary to replace the num lock board, disconnect the num lock board cable 3 from the LED board. 10. Remove the Phillips PM2.0×3.0 screw 4 that secures the num lock board to the switch cover and remove the num lock board 5. 11. Remove the switch cover.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures 3. Remove the three Phillips PM2.5×7.0 screws that secure the keyboard to the computer.
Removal and Replacement Procedures 4. Turn the computer display-side up with the front panel toward you. 5. Open the computer as far as possible. 6. Lift the rear edge of the keyboard 1 until it rests at an angle. 7. Slide the keyboard 2 back to disengage the tabs on the front edge of the keyboard from the top cover. 8. Swing the keyboard 3 forward until it rests on the palm rest.
Removal and Replacement Procedures 9. Release the ZIF connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board. Disconnecting the Keyboard Cable 10. Remove the keyboard. Reverse the above procedure to install the keyboard.
Removal and Replacement Procedures 5.12 Power Button Board Power Button Board Spare Part Number Information Power button board (includes power button board cable) 431438-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the switch cover (Section 5.10). 3. Remove the keyboard (Section 5.11). 4. Remove the Phillips PM2.0×3.0 screw 1 that secures the power button board to the computer. 5. Release the power button board 2 from the computer as far as the cables will allow.
Removal and Replacement Procedures 6. Disconnect the microphone cable 1 and the speaker assembly cable 2 from the power button board. 7. Release the ZIF connector 3 to which the power button board cable is connected and disconnect the cable. 8. Remove the power button board 4. Removing the Power Button Board Reverse the above procedure to install the power button board.
Removal and Replacement Procedures 5.13 Display Assembly Display Assembly Spare Part Number Information For use with full-featured computer models (includes microphones) 15.4-inch, WXGA, TFT with BrightView 15.4-inch, WXGA, TFT Antiglare 432304-001 432305-001 For use with defeatured computer models (does not include microphones) 15.4-inch, WXGA, TFT with BrightView 15.4-inch, WXGA, TFT Antiglare 432302-001 432303-001 1. Prepare the computer for disassembly (Section 5.3). 2.
Removal and Replacement Procedures 5. Disconnect the display cable 1 from the system board. 6. Disconnect the microphone cable 2 from the power button board. 7. Remove the wireless antenna cables 3 from the clips in the top cover.
Removal and Replacement Procedures Ä CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other computer components. 8. Remove the four Phillips PM2.5×7.0 screws 1 that secure the display assembly to the computer. 9. Remove the display assembly 2.
Removal and Replacement Procedures 10. Remove the eight rubber screw covers from the display bezel. are three different sizes of rubber screw covers on the ✎ There display bezel: 1 Four covers on the top edge of the bezel 2 Two covers on the lower bezel corners 3 Two covers on the lower-inside edge The display rubber screw covers are included in the Display Screw Kit, spare part number 431400-001.
Removal and Replacement Procedures 11. Remove the eight Phillips PM2.5×7.0 screws that secure the display bezel to the display assembly.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Display bezels For use with full-featured computer models (includes microphone openings) For use with defeatured computer models 433283-001 433284-001 12. Flex the inside edges of the left and right sides 1 and the top and bottom sides 2 of the display bezel until the bezel disengages from the display enclosure. 13. Remove the display bezel 3.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Display inverter 431391-001 14. Remove the inverter 1 from the display enclosure. 15. Disconnect the display cable 2 and the backlight cable 3 from the display inverter.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Display panels 15.4-inch, WXGA, SVA display panel with BrightView 15.4-inch, WXGA, SVA display panel AntiGlare 431386-001 431387-001 16. Remove the four Phillips PM2.5×5.0 screws 1 that secure the display panel to the display enclosure. 17. Remove the display panel 2.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Display Hinge Kit 433288-001 18. Remove the two Phillips PM2.0×3.0 screws 1 that secure each hinge to the display enclosure. 19. Remove the display hinges 2.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Wireless antenna transceivers and cables 431398-001 20. If it is necessary to replace the wireless transceivers and cables, remove the Phillips PM2.0×4.0 screw 1 that secures each transceiver to the display enclosure. 21. Remove the wireless antenna cables from the clips 2 built into the display enclosure. 22. Detach the wireless antenna transceivers 3 from the display enclosure. 23.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Microphone Kit (includes microphone receivers and cables) 431393-001 24. If it is necessary to replace the microphones and cables, release the retention tabs 1 built into the display enclosure that secure the microphones and cables to the display enclosure. 25. Remove the microphones 2 from the clips in the display enclosure. 26. Remove the microphone cables 3 from the display enclosure.
Removal and Replacement Procedures 5.14 Top Cover Top Cover Spare Part Number Information Top covers (include speakers, TouchPad, and TouchPad cable) For use with full-featured computer models For use with defeatured computer models 438186-001 431419-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Memory module compartment cover (Section 5.6) ❏ Optical drive (Section 5.9) ❏ Switch cover (Section 5.10) ❏ Keyboard (Section 5.
Removal and Replacement Procedures 2. Turn the computer upside down with the front toward you. 3. Remove the nine Phillips PM2.5×7.0 screws that secure the top cover to the computer.
Removal and Replacement Procedures 4. Remove the three Phillips PM2.5×4.0 screws 1 and the six Phillips PM2.5×5.0 screws 2 that secure the top cover to the computer.
Removal and Replacement Procedures 5. Turn the computer right-side up with the front toward you. 6.
Removal and Replacement Procedures 7. Remove the two Phillips PM2.0×6.0 screws 1 and the two Phillips PM2.5×5.0 screws 2 that secure the top cover to the computer.
Removal and Replacement Procedures 8. Lift the front edge of the top cover 1 until it disengages from the computer. 9. Remove the top cover 2. Removing the Top Cover Reverse the above procedure to install the top cover.
Removal and Replacement Procedures 5.15 Audio Board Audio Board Spare Part Number Information For use with full-featured computer models (includes infrared lens) For use with defeatured computer models (does not include infrared lens) 431443-001 431444-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Memory module compartment cover (Section 5.6) ❏ Optical drive (Section 5.9) ❏ Switch cover (Section 5.10) ❏ Keyboard (Section 5.
Removal and Replacement Procedures 2. Remove the two Phillips PM2.5×5.0 screws 1 that secure the audio board to the computer. 3. Slide the audio board 2 back to disengage the audio connectors from the base enclosure. 4. Remove the audio board 3. 5. Disconnect the audio board cable 4 from the audio board. Removing the Audio Board Reverse the above procedure to install the audio board.
Removal and Replacement Procedures 5.16 Bluetooth Module Bluetooth Module Spare Part Number Information Bluetooth module (includes Bluetooth module cable) 412766-002 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Memory module compartment cover (Section 5.6) ❏ Optical drive (Section 5.9) ❏ Switch cover (Section 5.10) ❏ Keyboard (Section 5.11) ❏ Display assembly (Section 5.13) ❏ Top cover (Section 5.
Removal and Replacement Procedures 2. Disconnect the Bluetooth module cable 1 from the system board. 3. Remove the two Phillips PM2.0×3.0 screws 2 that secure the Bluetooth module to the system board. 4. Remove the Bluetooth module 3. Removing the Bluetooth Module Reverse the above procedure to install the Bluetooth module.
Removal and Replacement Procedures 5.17 ExpressCard Assembly ExpressCard Assembly Spare Part Number Information ExpressCard assembly 431440-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Memory module compartment cover (Section 5.6) ❏ Optical drive (Section 5.9) ❏ Switch cover (Section 5.10) ❏ Keyboard (Section 5.11) ❏ Display assembly (Section 5.13) ❏ Top cover (Section 5.
Removal and Replacement Procedures 2. Push in on the ExpressCard bezel 1 to release the bezel from the ExpressCard slot. 3. Remove the ExpressCard bezel 2 from the ExpressCard slot. ExpressCard bezel is included in the Plastics Kit, spare ✎ The part number 438669-001.
Removal and Replacement Procedures 4. Remove the four Phillips PM2.5×4.0 screws 1 that secure the ExpressCard assembly to the system board. 5. Slide the ExpressCard assembly 2 to the right to disconnect it from the system board. 6. Remove the ExpressCard assembly 3. Removing the ExpressCard Assembly Reverse the above procedure to install the ExpressCard assembly.
Removal and Replacement Procedures 5.18 USB/Power Connector Board USB/Power Connector Board Spare Part Number Information USB/power connector boards (include USB/power connector board cable) For use with 90-W AC adapters For use with 65-W AC adapters 431446-001 431445-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Memory module compartment cover (Section 5.6) ❏ Optical drive (Section 5.9) ❏ Switch cover (Section 5.
Removal and Replacement Procedures 2. Remove the two Phillips PM2.5×5.0 screws 1 that secure the USB/power connector board to the computer. 3. Release the USB/power connector board 2 as far as the USB/power connector board cable will allow. 4. Disconnect the USB board cable 3 and the power connector board cable 4 from the USB/power connector board. Removing the USB/Power Connector Board 5. Remove the USB/power connector board. Reverse the above procedure to install the USB/power connector board.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures ❏ Audio board (Section 5.15) ❏ USB/power connector board (Section 5.18) 2. Remove the USB/power connector board cable 1 from the clips in the base enclosure. 3. Remove the two Phillips PM2.5×4.0 screws 2 that secure the system board to the base enclosure.
Removal and Replacement Procedures 4. Use the optical drive connector 1 to lift the right side of the system board 2 until it rests at an angle. 5. Slide the system board 3 to the right until the connectors on the left side of the system board disengage from the base enclosure. 6. Remove the system board.
Removal and Replacement Procedures 7. If it is necessary to replace the USB/power connector board cable or the audio board cable, turn the system board upside down with the front toward you. 8. Disconnect the USB/power connector board cable 1 and the audio board cable 2 from the system board. Removing the System Board Cables Reverse the above procedure to install the system board, USB/power connector board cable, and audio board cable.
Removal and Replacement Procedures 5.20 Fan/Heat Sink Assembly Fan/Heat Sink Assembly Spare Part Number Information Fan/heat sink assembly for use only with computer models using AMD processors Fan/heat sink assembly for use only with computer models using Intel processors 431450-001 434746-001 replacing the fan/heat sink assembly, be sure the power ✎ When button board is removed from the defective fan/heat sink assembly and installed on the replacement fan/heat sink assembly. Refer to Section 5.
Removal and Replacement Procedures 3. Disconnect the fan cable 1 from the system board. 4. Remove the four Phillips PM2.5×5.0 screws 2 that secure the fan/heat sink assembly to the system board. 5. Remove the fan/heat sink assembly 3.
Removal and Replacement Procedures thermal pads and thermal paste should be thoroughly ✎ The cleaned from the surfaces of the fan/heat sink assembly 1, 2, and 3, the system board components 4 and 6, and the processor 5 each time the fan/heat sink assembly is removed. Thermal pads and thermal paste should be installed on all surfaces before the fan/heat sink assembly is reinstalled. Thermal pads and thermal paste are included with all fan/heat sink assembly, system board, and processor spare part kits.
Removal and Replacement Procedures 5.21 Processor Processor Spare Part Number Information Intel Core Duo T7200 (2.00-GHz) Intel Core Duo T1350 (1.86-GHz) Intel Core Duo T5600 (1.83-GHz) Intel Core Duo T2350 (1.60-GHz), for use with V6200 models Intel Core Duo T2250 (1.73-GHz) Intel Core Duo T5500 (1.66-GHz) Intel Core Duo T5200 (1.66-GHz), for use with V6200 models Intel Core Duo T2060 (1.60-GHz), for use with V6200 models Intel Core Duo T2050 (1.
Removal and Replacement Procedures 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: ❏ Hard drive (Section 5.4) ❏ Memory module compartment cover (Section 5.6) ❏ Optical drive (Section 5.9) ❏ Switch cover (Section 5.10) ❏ Keyboard (Section 5.11) ❏ Display assembly (Section 5.13) ❏ Top cover (Section 5.14) ❏ System board (Section 5.19) ❏ Fan/heat sink assembly (Section 5.
Removal and Replacement Procedures 2. Turn the processor locking screw 1 one-half turn counterclockwise until you hear a click. 3. Lift the processor 2 straight up and remove it. The gold triangle 3 on the processor should be aligned with ✎ the triangle icon 4 embossed on the processor socket when you install the processor. Removing the Processor Reverse the above procedure to install the processor.
6 Specifications This chapter provides physical and performance specifications. Table 6-1 Computer Dimensions Length Width Height (varies front to rear) Weight (varies by configuration) 35.7 cm 25.7 cm 4.1 cm 14.05 in 10.12 in 1.57 in 2.7 kg 5.8 lb Stand-alone power requirements Operating voltage Operating current 18.5 V dc —19.0 V dc 3.5 A or 4.
Specifications Table 6-1 Computer (Continued) Shock Operating Nonoperating 125 g, 2 ms, half-sine 200 g, 2 ms, half-sine Random Vibration Operating Nonoperating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate *Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures.
Specifications Table 6-2 15.4-inch, WXGA, SVA Display Dimensions Height Width Diagonal 20.7 cm 33.1 cm 39.1 cm Number of colors Up to 16.8 million Contrast ratio 200:1 Brightness 160 nits typical 8.15 in 13.03 in 15.39 in Pixel resolution Pitch Format Configuration 0.259 × 0.
Specifications Table 6-3 Hard Drives 200-GB* 160-GB* 9.5 mm 70 mm 99 g 9.
Specifications Table 6-3 Hard Drives (Continued) 120-GB* 100-GB* 9.5 mm 70 mm 102 g 9.
Specifications Table 6-3 Hard Drives (Continued) 80-GB* 60-GB* 40-GB* Dimensions Height Width Weight Interface type 9.5 mm 70 mm 99 g 9.5 mm 70 mm 99 g 9.
Specifications Table 6-4 Primary 6-cell, Li-Ion Battery Dimensions Height Width Depth Weight 2.00 cm 9.40 cm 13.40 cm 0.34 kg 0.79 in 3.70 in 5.28 in 0.75 lb Energy Voltage Amp-hour capacity Watt-hour capacity 11.1 V 4.
Specifications Table 6-5 DVD/CD-RW Combo Drive Applicable disc Read: Write: DVD-R, DVD-RW, CD-R and CD-RW DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Disc diameter Standard disc Mini disc 6–8 12 cm (4.72 in) 8 cm (3.
Specifications Table 6-5 DVD/CD-RW Combo Drive (Continued) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD media DVD media < 110 ms < 210 ms < 130 ms < 225 ms Random Full stroke Audio output level Line-out, 0.7 V rms Cache buffer 2 MB Data transfer rate CD-R (24X) CD-RW (10X) CD-ROM (24X) DVD (8X) Multiword DMA mode 2 3600 KB/s (150 KB/s at 1X CD rate) 1500 KB/s (150 KB/s at 1X CD rate) 3600 KB/s (150 KB/s at 1X CD rate) 10,800 KB/s (1352 KB/s at 1X DVD rate) 16.
Specifications Table 6-6 DVD±RW/R and CD-RW Double-Layer Combo Drive Applicable disc Read: Write: DVD-R, DVD-RW, CD-R and CD-RW DVD-ROM (DVD-5, DVD-R and DVD-RW DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Disc diameter Standard disc Mini disc 6–10 12 cm (4.72 in) 8 cm (3.
Specifications Table 6-6 DVD±RW/R and CD-RW Double-Layer Combo Drive (Continued) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD media DVD media < 175 ms < 285 ms < 230 ms < 335 ms Random Full stroke Audio output level Audio-out, 0.
Specifications Table 6-7 System DMA Hardware DMA System Function DMA0 Not applicable DMA1 Not applicable DMA2 Not applicable DMA3 Not applicable DMA4 Direct memory access controller DMA5 Available for ExpressCard DMA6 Not assigned DMA7 Not assigned 6–12 Maintenance and Service Guide
Specifications Table 6-8 System Interrupts Hardware IRQ System Function IRQ0 System timer IRQ1 Quick Launch buttons IRQ2 Cascaded IRQ3 USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—Link Audio SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7* Parallel port IRQ8 System CMOS/real-time clock IRQ9* Microsoft ACPI-compliant system IRQ10* USB UHCI controller—24C2 GM/GME Graphic Controller Realtek RTL8139 Family PCI fast Ethernet Controller IRQ11
Specifications Table 6-8 System Interrupts (Continued) Hardware IRQ System Function IRQ12 Synaptics PS/2 port pointing device IRQ13 Numeric data processor IRQ14 Primary IDE channel IRQ15 Secondary IDE channel IRQ17 Conexant AC -Link Audio IRQ17 Soft V90 Data Fax Modem with SmartCP IRQ17 ATi Mobility Radeon Xpress 200 Series IRQ19 Standard Enhanced PCI to USB Host Controller IRQ19 Standard OpenHCD USB Host Controller IRQ19 Standard OpenHCD USB Host Controller IRQ20 TI 6411 PCIxx21/x51
Specifications Table 6-9 System I/O Addresses I/O Address (hex) System Function (shipping configuration) 0x00000000-0x00000CF7 PCI bus 0x00000000-0x00000CF7 Direct memory access controller 0x00000020-0x00000021 Programmable interrupt controller 0x0000002E-0x0000002F System board resources 0x00000040-0x00000043 System timer 0x00000060-0x00000060 Quick Launch Buttons 0x00000061-0x00000061 System speaker 0x00000062-0x00000062 Microsoft ACPI-Compliant Embedded Controller 0x00000064-0x00000064
Specifications Table 6-9 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0x000001F0-0x000001F7 Primary IDE Channel 0x00000220-0x0000022F System board resources 0x00000274-0x00000277 ISAPNP Read Data Port 0x00000279-0x00000279 ISAPNP Read Data Port 0x00000280-0x00000293 System board resources 0x00000376-0x00000376 Secondary IDE Channel 0x000003B0-0x000003BB PCI standard PCI-to-PCI bridge 0x000003B0-0x000003BB ATI MOBILITY RADEON Xpress 200 Series
Specifications Table 6-9 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0x00000C6F-0x00000C6F System board resources 0x00000CD4-0x00000CD5 System board resources 0x00000CD6-0x00000CD7 System board resources 0x00000CD8-0x00000CDF System board resources 0x00000D00-0x0000FFFF PCI bus 0x00000F40-0x00000F47 System board resources 0x00001080-0x00001080 System board resources 0x00008000-0x0000805F System board resources 0x00008100-0x000081FF System b
Specifications Table 6-10 System Memory Map Memory Map Address (hex) System Function (shipping configuration) 0xD4100000-0xD41FFFFF PCI standard PCI-to-PCI bridge 0xD4100000-0xD41FFFFF ATI MOBILITY RADEON Xpress 200 Series 0xD8000000-0xDBFFFFFF PCI standard PCI-to-PCI bridge 0xD8000000-0xDBFFFFFF ATI MOBILITY RADEON Xpress 200 Series 0xFAC00000-0xFEBFFFFF PCI standard PCI-to-PCI bridge 0xF6C00000-0xFABFFFFF PCI standard PCI-to-PCI bridge 0xD4000000-0xD4000FFF Standard OpenHCD USB Host Contro
Specifications Table 6-10 System Memory Map (Continued) Memory Map Address (hex) System Function (shipping configuration) 0xF2C00000-0xF6BFFFFF Texas Instruments PCIxx21/x515 Cardbus Controller 0xD4206000-0xD4207FFF Texas Instruments PCIxx21 Integrated FlashMedia Controller 0xD4209000-0xD42090FF SDA Standard Compliant SD Host Controller 0xD4208C00-0xD4208CFF SDA Standard Compliant SD Host Controller 0xD4208800-0xD42088FF SDA Standard Compliant SD Host Controller 0xD4209400-0xD42094FF Realtek R
A Screw Listing This appendix provides specification and reference information for the screws used in the computer. The four Phillips PM3.0×3.0 screws (Table A-1) used to secure the hard drive bracket to the hard drive. The remainder of the screws listed in this appendix are available in the Screw Kits, spare part numbers 434983-001 (for use with computers using Intel processors) and the Display Screw Kit, spare part number 431400-001.
Screw Listing Table A-1 Phillips PM3.0×3.0 Screw mm Color Qty. Length Thread Head Width Silver 6 3.0 mm 3.0 mm 5.0 mm Where used: 6 screws that secure the hard drive bracket to the hard drive (documented in Section 5.4) Phillips PM3.0×3.
Screw Listing Table A-2 Phillips PM2.0×5.0 Captive Screw mm Color Qty. Length Thread Head Width Black 5 5.0 mm 2.0 mm 5.0 mm Where used: 1 Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C-clips; documented in Section 5.4) 2 Three screws that secure the memory module compartment cover to the computer (screws are captured on the cover by C-clips; documented in Section 5.6) Phillips PM2.0×5.
Screw Listing Table A-3 Phillips PM2.0×3.0 Screw mm Color Qty. Length Thread Head Width Silver 12 3.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the Mini Card module to the computer (documented in Section 5.8) Phillips PM2.0×3.
Screw Listing Table A-3 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 12 3.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the optical drive bracket to the optical drive (documented in Section 5.9) Phillips PM2.0×3.
Screw Listing Table A-3 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 12 3.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the num lock board to the switch cover (documented in Section 5.10) Phillips PM2.0×3.
Screw Listing Table A-3 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 12 3.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the power button board to the computer (documented in Section 5.12) Phillips PM2.0×3.
Screw Listing Table A-3 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 12 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the display hinges to the display panel (documented in Section 5.13) Phillips PM2.0×3.
Screw Listing Table A-3 Phillips PM2.0×3.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 12 3.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the Bluetooth module to the system board (documented in Section 5.16) Phillips PM2.0×3.
Screw Listing Table A-4 Phillips PM2.5×7.0 Screw mm Color Qty. Length Thread Head Width Black 25 7.0 mm 2.5 mm 5.0 mm Where used: 1 One screw that secures the optical drive to the computer (documented in Section 5.9) 2 Three screws that secure the keyboard to the computer (documented in Section 5.11) Phillips PM2.5×7.
Screw Listing Table A-4 Phillips PM2.5×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 25 7.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the display assembly to the computer (documented in Section 5.13) Phillips PM2.5×7.
Screw Listing Table A-4 Phillips PM2.5×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 25 7.0 mm 2.5 mm 5.0 mm Where used: 8 screws that secure the display bezel to the display assembly (documented in Section 5.13) Phillips PM2.5×7.
Screw Listing Table A-4 Phillips PM2.5×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 25 7.0 mm 2.5 mm 5.0 mm Where used: 9 screws that secure the top cover to the computer (documented in Section 5.14) Phillips PM2.5×7.
Screw Listing Table A-5 Phillips PM2.5×10.0 Screw mm Color Qty. Length Thread Head Width Black 2 10.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the switch cover to the computer (documented in Section 5.10) Phillips PM2.5×10.
Screw Listing Table A-6 Phillips PM2.5×5.0 Screw mm Color Qty. Length Thread Head Width Silver 20 5.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the display panel to the display enclosure (documented in Section 5.13) Phillips PM2.5×5.
Screw Listing Table A-6 Phillips PM2.5×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 20 5.0 mm 2.5 mm 5.0 mm Where used: 6 screws that secure the top cover to the base enclosure (documented in Section 5.14) Phillips PM2.5×5.
Screw Listing Table A-6 Phillips PM2.5×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 20 5.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the top cover to the base enclosure (documented in Section 5.14) Phillips PM2.5×5.
Screw Listing Table A-6 Phillips PM2.5×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 20 5.0 mm 2.5 mm 5.0 mm Where used: 1 Two screws that secure the audio board to the base enclosure (documented in Section 5.15) 2 Two screws that secure the USB/power connector board to the base enclosure (documented in Section 5.18) Phillips PM2.5×5.
Screw Listing Table A-6 Phillips PM2.5×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 20 5.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the fan/heat sink assembly to the system board (documented in Section 5.20) Phillips PM2.5×5.
Screw Listing Table A-7 Phillips PM2.0×4.0 Screw mm Color Qty. Length Thread Head Width Silver 2 4.0 mm 2.0 mm 5.0 mm Where used: 2 screws that secure the wireless antenna transceivers to the display enclosure (documented in Section 5.13) Phillips PM2.0×4.
Screw Listing Table A-8 Phillips PM2.5×4.0 Screw mm Color Qty. Length Thread Head Width Silver 9 4.0 mm 2.5 mm 5.0 mm Where used: 3 screws that secure the top cover to the base enclosure (documented in Section 5.14) Phillips PM2.5×4.
Screw Listing Table A-8 Phillips PM2.5×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 9 4.0 mm 2.5 mm 5.0 mm Where used: 1 4 screws that secure the ExpressCard assembly to the system board (documented in Section 5.17) 2 2 screws that secure the system board to the computer (documented in Section 5.19) Phillips PM2.5×4.
Screw Listing Table A-9 Phillips PM2.0×6.0 Screw mm Color Qty. Length Thread Head Width Black 2 6.0 mm 2.0 mm 5.0 mm Where used: 2 screws that secure the top cover to the base enclosure (documented in Section 5.14) Phillips PM2.0×6.
B Backup and Recovery in Windows XP Recovering System Information Tools provided by the operating system and PC Recovery software are designed to help you with the following tasks for safeguarding your information and restoring it in case of a system failure: ■ Backing up your information regularly to protect your important system files. ■ Making a set of recovery discs (PC Recovery software feature).
Backup and Recovery in Windows XP Backing Up Your Information When to Back Up ■ On a regularly scheduled basis ✎ Set reminders to back up your information periodically. ■ Before the computer is repaired or restored ■ Before you add or modify hardware or software Backup Suggestions ■ Create system restore points using Windows XP Professional System Restore feature. ■ Store personal files in the My Documents folder and back up these folders periodically.
Backup and Recovery in Windows XP Using System Restore Points When you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system. to an earlier restore point does not affect data files ✎ Recovering saved or e-mails created since the last restore point.
Backup and Recovery in Windows XP Restoring to a Previous Date and Time To revert to a restore point (created at a previous date and time), when the computer was functioning optimally: 1. Select Start > Help and Support > System Restore. The System Restore window opens. 2. Click Restore my computer to an earlier time, and then click Next. 3. Follow the on-screen instructions. Creating Recovery Discs PC Recovery Disc Creator creates a set of recovery CDs or DVDs for the computer.
Backup and Recovery in Windows XP ■ Number each disc before inserting it into the computer optical drive. ■ If necessary, you can exit the program before you have finished creating the recovery discs. The next time you open PC Recovery Disc Creator, you will be prompted to continue the disc creation process. To create a set of recovery discs: 1. Select Start > All Programs > System Recovery > PC Recovery Disc Creator. The PC Recovery Disc Creator tool opens. 2. Click Next.
Backup and Recovery in Windows XP Reinstalling Software Programs and Drivers If a program or driver preinstalled at the factory is accidentally erased or is damaged, the Application and Driver Recovery tool allows you to reinstall it. not provided with this computer must be reinstalled ✎ Software from the disc provided by the manufacturer or downloaded from the manufacturer's Web site. ✎ Before reinstalling the program, be sure it is fully uninstalled.
Backup and Recovery in Windows XP 2. Select Start > All Programs > System Recovery > Application and Driver Recovery. The Application and Driver Recovery tool opens. 3. Select Application Installation or Driver Installation, and then click Next. 4. Follow the on-screen instructions to complete the program or driver recovery. 5. Restart the computer if prompted. Reinstalling Programs from Discs 1. Insert the disc into the optical drive. 2.
Backup and Recovery in Windows XP Recovering from the Recovery Discs To restore the system from the recovery discs: 1. Back up all personal files. 2. Insert the first recovery disc into the optical drive and restart the computer. 3. Follow the on-screen instructions. Recovering from the Partition on the Hard Drive You can perform a recovery from the partition on the hard drive from either the Start button or f11. To restore the system from the partition: 1.
Backup and Recovery in Windows XP If you want to perform a destructive recovery: destructive recovery formats the hard drive and restores the ✎ Acomputer to its factory state. Select this option only as a last resort. a. Click Advanced Options on the System Recovery screen. b. Select Destructive Recovery and follow the on-screen instructions.
Backup and Recovery in Windows XP 4. Click OK. 5. At the System Recovery screen, click Advanced Options. 6. Select Delete Recovery Partition (not recommended) and follow the on-screen instructions. Updating Reinstalled Software After you perform a system recovery, connect to the Internet to update all reinstalled software. To access update links for the operating system and other software provided on your computer: » Select Start > Help and Support.
C Backup and Recovery in Windows Vista Recovering System Information Tools provided by the operating system and Recovery Manager software are designed to help you with the following tasks for safeguarding your information and restoring it in case of a system failure: ■ Back up your information regularly to protect your important system files. ■ Make a set of recovery discs (Recovery Manager software feature).
Backup and Recovery in Windows Vista Backing up Your Information When to Back Up ■ On a regularly scheduled basis. ✎ Set reminders to back up your information periodically. ■ Before the computer is repaired or restored. ■ Before you add or modify hardware or software. Backup Suggestions ■ Create system restore points using the Windows System Restore feature. ■ Store personal files in the Documents folder and back up these folders periodically.
Backup and Recovery in Windows Vista Using System Restore Points When you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system. to an earlier restore point does not affect data files ✎ Recovering saved or e-mails created since the last restore point.
Backup and Recovery in Windows Vista Restoring to a Previous Date and Time To revert to a restore point (created at a previous date and time), when the computer was functioning optimally, follow these steps: 1. Select Start > Control Panel > System and Maintenance > System. 2. In the left pane, click System protection. 3. Click the System Protection tab. 4. Click the System Restore button, and then click Next. The System Restore window opens. 5. Follow the on-screen instructions.
Backup and Recovery in Windows Vista ■ If necessary, you can exit the program before you have finished creating the recovery discs. The next time you open Recovery Manager, you will be prompted to continue the disc creation process. To create a set of recovery discs: 1. Select Start > All Programs > Recovery Manager > Recovery Manager. Recovery Manager opens. 2. Click Advanced Options.
Backup and Recovery in Windows Vista ■ In all cases, if a program has been deleted from your computer, the reinstallation process reinstalls the program or utility to the factory image but cannot restore your personal settings. Reinstalling Preinstalled Programs and Drivers 1. Remove the program or driver: some cases, drivers are not listed in the Programs and ✎ InFeatures list. If the driver is not listed, it does not need to be removed. a. Select Start > Control Panel > Programs > Uninstall a program.
Backup and Recovery in Windows Vista Performing a Recovery Recovery Manager software allows you to repair or restore the system if you experience system failure or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery partition on the hard drive. has its own built-in repair features, such as System ✎ Windows Restore and driver rollback capabilities. If you have not already tried these features, try them before using Recovery Manager.
Backup and Recovery in Windows Vista ❏ Restart the computer and press f11 while the “Press for recovery” message is displayed on the screen. Then select Recovery Manager. Recovery Manager opens. 2. Click Advanced Options. 3. Click System recovery, and then click Next. 4. Follow the on-screen instructions. Deleting the Recovery Partition on the Hard Drive The Recovery Manager Advanced Options menu provides the option of deleting the recovery partition, which will increase space on the hard drive.
Backup and Recovery in Windows Vista Updating Reinstalled Software After you perform a system recovery, connect to the Internet to update all reinstalled software. To access update links for the operating system and other software provided on your computer: » Select Start > Help and Support. To update optional software, follow the instructions provided by the software manufacturer. Some programs include an update feature you can access from a Help button or menu within the program.
D Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Ä CAUTION: The procedures in this appendix can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. Careful handling should be exercised when removing these components.
Display Component Recycling This appendix provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight 1 and the LCD panel 2. procedures differ from one display assembly to ✎ Disassembly another. The procedures provided in this appendix are general disassembly instructions. Specific details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.
Display Component Recycling Perform the following steps to disassemble the display assembly: 1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
Display Component Recycling 2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel 3.
Display Component Recycling 4. Disconnect all LCD panel cables 1 from the display inverter board and remove the inverter board 2.
Display Component Recycling 5. Remove all screws 1 that secure the LCD panel to the display enclosure. 6. Remove the LCD panel 2 from the display enclosure.
Display Component Recycling 7. Turn the LCD panel upside down. 8. Remove all screws that secure the LCD panel frame to the LCD panel.
Display Component Recycling 9. Use a sharp-edged tool to cut the tape 1 that secures the side of the LCD panel to the LCD panel frame. 10. Remove the LCD panel frame 2 from the display panel.
Display Component Recycling 11. Remove the screws 1 that secure the backlight cover to the LCD panel. 12. Lift the top edge of the backlight cover 2 and swing it forward. 13. Remove the backlight cover.
Display Component Recycling 14. Turn the LCD panel right-side up. 15. Remove the backlight cables 1 from the clip 2 in the LCD panel.
Display Component Recycling 16. Turn the LCD panel upside down. 17. Remove the backlight frame from the LCD panel.
Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 18. Slide the backlight out of the backlight frame.
Display Component Recycling 19. Disconnect the display cable 1 from the LCD panel. 20. Remove the screws 2 that secure the LCD panel to the LCD rear panel. 21. Release the LCD panel 3 from the LCD rear panel. 22. Release the tape 4 that secures the LCD panel to the LCD rear panel.
Display Component Recycling 23. Remove the LCD panel. Removing the LCD Panel 24. Recycle the backlight and LCD panel.
E Connector Pin Assignments Table D-1 Universal Serial Bus Pin Signal Pin Signal 1 +5 VDC 3 Data + 2 Data – 4 Ground Maintenance and Service Guide E–1
Connector Pin Assignments Table D-2 RJ-45 (Network) Pin Signal Pin Signal 1 Transmit + 5 Unused 2 Transmit – 6 Receive – 3 Receive + 7 Unused 4 Unused 8 Unused E–2 Maintenance and Service Guide
Connector Pin Assignments Table D-3 S-Video-Out Pin Signal Pin Signal 1 TV-Ground 5 TV-CD 2 TV-CVBS 6 TV-Ground 3 TV-Ground 7 TV-YD 4 TV-Ground Maintenance and Service Guide E–3
Connector Pin Assignments Table D-4 External Monitor Pin Signal Pin Signal 1 Red analog 9 +5 VDC 2 Green analog 10 Ground 3 Blue analog 11 Monitor detect 4 Not connected 12 DDC 2B data 5 Ground 13 Horizontal sync 6 Ground analog 14 Vertical sync 7 Ground analog 15 DDC 2B clock 8 Ground analog E–4 Maintenance and Service Guide
Connector Pin Assignments Table D-5 RJ-11 (Modem) Pin Signal Pin Signal 1 Unused 4 Unused 2 Tip 5 Unused 3 Ring 6 Unused Maintenance and Service Guide E–5
Connector Pin Assignments Table D-6 Audio-In (Microphone) Pin Signal Pin Signal 1 Audio signal in 3 Ground 2 Audio signal in Table D-7 Audio-Out (Headphone) Pin Signal Pin Signal 1 Audio out, left channel 3 Ground 2 Audio out, right channel E–6 Maintenance and Service Guide
F Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.
Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries and regions. F–2 ■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft). ■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used.
Power Cord Set Requirements Country/Region-Specific Requirements 3-Conductor Power Cord Set Requirements Country/Region Accredited Agency Applicable Note Number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Power Cord Set Requirements 3-Conductor Power Cord Set Requirements (Continued) Country/Region Accredited Agency Applicable Note Number Korea ek 4 The Netherlands keMa 1 Norway NEMKO 1 People’s Republic of China ccc 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan bsmi 4 United Kingdom BSI 1 United States UL 2 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Index Index 1394 port 1–9 A AC adapter, spare part numbers 3–27, 3–30, 3–38 analog TV tuner, spare part number 3–27, 3–35 Antenna Adapter - DVB-T, spare part numbers 3–28 arrow keys 1–13 audio board removal 5–48 spare part numbers 3–8, 3–37, 3–38, 5–48 audio board cable, removal 5–60 audio troubleshooting 2–31 audio-in (microphone) jack location 1–7 pin assignments D–6 audio-out (headphone) jack location 1–7 pin assignments D–6 B backpack, spare part number 3–27, 3–31 Backup and Recovery Windows Vista C–
Index right-side 1–10 top 1–14, 1–16, 1–18 composite S-Video and audio input cable, spare part number 3–27, 3–35 computer feet, locations 5–10 Computer Setup Advanced Menu 2–7, 2–14 File Menu 2–5, 2–12 Security Menu 2–6, 2–12 Tools Menu 2–6, 2–12 computer specifications 6–1 connector pin assignments external monitor D–4 headphone D–6 microphone D–6 monitor D–4 RJ-11 (modem) D–5 RJ-45 (network) D–2 S-Video-out D–3 Universal Serial Bus (USB) D–1 connectors, service considerations 4–2 consumer infrared lens 1
Index drive light 1–7 drives, preventing damage 4–3 DVB-T TV Tuner, spare part numbers 3–35 DVBTV tuner, spare part number 3–27 DVD/CD-RW Combo Drive OS loading problems 2–30 precautions 4–3 removal 5–20 spare part number 3–10, 3–24, 3–37, 5–20 specifications 6–8 DVD±RW/R and CD-RW Combo Drive OS loading problems 2–30 precautions 4–3 removal 5–20 spare part numbers 3–10, 3–24, 3–37, 5–20 specifications 6–10 E electrostatic discharge 4–4, 4–8 expansion port 3 1–8 ExpressCard assembly removal 5–52 spare par
Index H hard drive OS loading problems 2–26 precautions 4–3 removal 5–6 spare part numbers 3–10, 3–24, 3–36, 3–37, 3–39, 3–40, 3–41, 5–6 specifications 6–4 hard drive bay 1–21 Hard Drive Bracket Kit, spare part number 3–24, 3–40, 5–6 hard drive bracket, removal 5–9 hard drive cover illustrated 3–25 removal 5–7 HDMI port 1–9 headphone jack location 1–7 pin assignments D–6 headset, spare part number 3–27, 3–30 hinge removal 5–39 spare part number 3–22, 3–39, 5–39 I I/O address specifications 6–15 infrared r
Index microphone jack location 1–7 pin assignments D–6 Mini Card module removal 5–15 spare part numbers 3–12, 3–14, 3–16, 3–18, 3–20, 3–31, 3–32, 3–33, 3–34, 3–35, 5–15 modem jack location 1–9 pin assignments D–5 modem, troubleshooting 2–36 monitor port location 1–8 pin assignments D–4 mouse, spare part number 3–27, 3–28, 3–40 N network jack location 1–9 pin assignments D–2 network, troubleshooting 2–36 nonfunctioning device, troubleshooting 2–24, 2–33 num lock board, removal 5–24 num lock key 1–13 O opt
Index R rear components 1–8 recovering from partition on hard drive Windows Vista C–7 Windows XP B–8 recovering from the recovery discs Windows Vista C–7 Windows XP B–8 remote control spare part numbers 3–40, 3–41 remote control, spare part numbers 3–27, 3–33, 3–40 removal preliminaries 4–1 procedures 5–1 replacement preliminaries 4–1 procedures 5–1 RF cable, spare part number 3–27, 3–35 RF input adapter cable, spare part number 3–27, 3–35 right-side components 1–10 RJ-11 (modem) jack location 1–9 pin assi
Index spare part numbers 3–8, 3–35, 3–39, 3–41, 3–42, 5–57 system DMA 6–12 T tools required 4–1 top components 1–14, 1–16, 1–18 top cover removal 5–42 spare part numbers 3–5, 3–40, 5–42 TouchPad 1–19 TouchPad buttons 1–19 TouchPad horizontal scroll zone 1–19 TouchPad light 1–19 TouchPad on/off button 1–19 TouchPad vertical scroll zone 1–19 transporting precautions 4–5 troubleshooting audio 2–31 docking device 2–24 flowcharts 2–15 keyboard 2–34 modem 2–36 network 2–36 nonfunctioning device 2–24, 2–33 OS lo
Index wireless antenna removal 5–40 spare part number 3–22, 3–36, 5–40 wireless laser mouse, spare part numbers 3–27, 3–35 wireless light 1–7 wireless switch 1–7 workstation precautions 4–6 Maintenance and Service Guide Index–8
Index Maintenance and Service Guide Index–9
Index Maintenance and Service Guide Index–10
Index Maintenance and Service Guide Index–11
