Digital 3-Channel Proportional RC System Instruction Manual RadioLink Electronics Co., Ltd Http://www.radiolink.com.
MENU 1. Introduction and service………………………………………………………….2 2. Safety guides……………………………………………………………….....…. 2 3. Battery recharge notice……………………………………………………..….…3 4. Contents and specifications………………………………………………..…..….4 5. Receiver installation and binding…………………………………………………5 6. Display when power switch turned on…………………………………….……... 6 7. Language Select "LANGUAGE"………………....……………………………......7 8. Model Select "MODEL"………………………………………………...................8 9. End Point Adjuster "EPA"………………………………….…..…..…………...
Introduction and Service Thank you for choosing RadioLink RC system, if you are the first time to use this type of products, please read this statement carefully and strictly in accordance with the requirements of operation. You could refer to the Manual if you meet any problems during the operation . Please well keep the manual after use because you might have to use it again next time. If you found any problems during the operation process, please refer to the manual.
The sequence to shut down is that turn off the receiver power first, and then shut down the transmitter. If the above operations are reverse, it might lead to uncontrolled situation and cause accidents The transmitter needs to be powered by 4 AA alkaline 5# batteries or Ni-MH batteries. Please check the voltage of batteries before using, as it might lead to uncontrolled situation and accidents when the voltage is lacked. So you must change the battery or recharge them in time.
Contents and specifications Contents and Specifications： Contents： 1.Antenna 2.Binding key 3.Channel connection pin Specs： Size：51.5*24*15（mm） Channel number：4 channels Power standard：4.6-6 V Frequency：2.4GHz Weight：5g Contents： 1. Antenna 2. LCD 3. Menu key 4. Turning wheel 5. Function key A throttle 6. Function key B Direction 7. Function key C the 3rd channel 8. The 3rd channel switch key 9. Power switch 10. Recharge connection slot 11. Throttle trigger Specs： Size：213*117*115.5(mm) Antenna length：105.
Low voltage alert：Yes（lower than 4.6V） Data resolution：1024 Frequency：2.4GHz RF range:300meters on ground Receiver installation and binding Receiver’s connection and installation： （such as some car model） Rudder Servo(CH1) Throttle Servo(CH2) Servo(CH3) NOTICE： 1． Confirm battery, switch, servos and etc are connected with receiver right. 2． While installing servos, please keep servo’s distance from model body, otherwise the vibration can lead to servo and make servo damaged.
1． 2． 3． 4． Load the battery into transmitter, power on it. Connect the power to the 2nd Channel pin of receiver. Press the binding button on the receiver till LED starts twinkling. LED stops the twinkle, bright light indicates a successful code-matching was completed.
you power on the transmitter. Please make sure the model name the screen displayed is the right what you want. If the model name you chose is not corresponding with your model, the pre-settings should be wrong. Transmitter battery voltage In addition to the model#, LCD can show the voltage of battery. When the voltage is lower than 4.6V, it would start the low-voltage alert, it would send out “BeBe…” sounds, till the transmitter is power-off.
2. Press “Enter” button to get into “LANGUAGE”function interface。 3. Use“Dec(-)”or “Inc(+)”key to select“中文”or “English”,the selected language will be with black shading effect. 4. Press “Enter” button, the desired language is selected,and return to the initial screen automatically. Model Select "MODEL" The RC3S transmitter can store model memories for five models. Use this function to call a new model #. MODEL- Model select function 1.
Setting item (channel and direction) ST-LFT:Steering (left side) ST-RGT:Steering (right side) TH-FWD:Throttle (foward side) TH-BRK:Throttle (brake side) 3C-UP:3rd channel (up side) 3C-DWN:3rd channel (down side) Steering EPA ST-LFT:0~120 ST-RGT:0~120 Initial value:120 Throttle EPA TH-FWD:0~120 TH-BRK:0~120 Initial value : 120 Steering EPA 3C-UP:0~120 3C-DWN:0~120 Initial value :120 End point adjustment 1.
Setup item RATE: Steering EXP rate Adjustment range -100~0~+100 Initial value :0 Steering operation curve adjustment 1.Access the function menu (By pressing “Exit” and “Enter” buttons simultaneously and holding them down for one second ), press “Inc(+)” button three times to chose EAP function. 2.
Setup item TURN:TURN direction RETURN:RETURN direction Adjustment range 1~100% (each direction) At 100%, there is no delay Steering servo delay 1.Access the function menu (By pressing “Exit” and “Enter” buttons simultaneously and holding them down for one second ), press “Inc(+)” button four times to chose STSPD function. 2.
Setup items RATE:Forward side rate FWD:Forward side curve selection BRK:Brake side rate Adjustment range RATE:-100 ~ 0 ~ +100 FWD: EXP, VTR, CRV BRK:-100 ~ 0 ~ +100 1.Enter the function menu and use “Dec(-)” or “Inc(+)” button to access THEXP function. 2.
the - side when you want to make the rise milder. (Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.) (2). Press “Enter” button, the adjusted BRK value stops blinking, now the BRK value has been set. 3.When ending setting, return to the initial screen by pressing “Exit” button twice. Adjustment method for VTR curve Setup items RATE:Forward side rate TG.
Forward side adjustment(select RATE) (1).Press “Enter” key, the current rate value will blink, Use “Inc(+)” button to adjust the + side when you want to quicken the rise and use “Dec(-)” button to adjust the side when you want to make the rise milder. (Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.) (2). Press “Enter” button, the adjusted RATE value stops blinking, now the RATE value has been set.
Adjustment range 1: ~ 5: 0 ~ 100% FWD: EXP, VTR, CRV BRK: -100 ~ 0 ~ +100% 1.Enter the function menu and use “Dec(-)” or “Inc(+)” button to access THEXP function. 2.
value has been set. 3.When ending setting, return to the initial screen by pressing “Exit” button twice. Throttle Speed "THSPD" Throttle servo delay Sudden trottle trigger operation on a slippery road only causes the wheels to spin and the ve-hicle cannot accelerate smoothly. Setting the throttle speed function reduces wasteful battery consumption while at the same time permitting smooth, enjoyable operation.
MODE setup item , then press “Enter” key, SPEED 2 or OFF will blink, press “Dec(-)” or “Inc(+)” button,when the blinking SPEED 2 or OFF change to blinking SPEED 1, press “Enter” key, SPEED 1 will stop blink,now SPEED 1 is selected}, press “Dec(-)” or “Inc(+)” button to select ALL setup item, then press “Enter” key, the initial value will blink, use “Dec(-)” or “Inc(+)” button to adjust the delay of the entire throttle forward side range.
2,press “Enter” key,SPEED 2 will stop blinking, now SPEED 2 is selected}, press “Dec(-)” or “Inc(+)” button to select "LOW" or "HIGH" delay adjustment or “TGP1” Speed switching point adjustment. 4.Press “Enter” key to confirm "LOW" or "HIGH" or “TGP1” setup item, and the value of your selected setup item will blink. Use “Dec(-)” or “Inc(+)” button to adjust the value.
STM: Steering mixing - ABP : Amount of brake returnSets the rate at which the servo returns versus trigger operation for brake release. When set to 0%, the ABS function is not performed. When set to 50%, the servo returns 50% (1/2) of the trigger operation amount and when set to 100%, the servo returns to the neutral position. - DLY : DelaySets the delay from brake operation to ABS operation. When set to 0%, the ABS function is activated without any delay.
"50":Return to the 50% position of the brake operation amount "100":Return to the neutral position. Brake return amount (ABP) 0 ~ 50 ~ 100 Initial value; 50 - Brake return amount (ABP) is influenced by the "EXP" rate on the brake side. 2. (Delay amount setup) Select the setting item "DLY" by pressing “Dec(-)” or “Inc(+)” button, then press “Enter” key and the initial value of “DLY” will blink. Use “Dec(-)” or “Inc(+)” button to adjust the delay amount.
- The smaller the set value, the faster the pulse speed. Cycle speed (CYC) 0 ~ 30 Initial value; 5 4. (Operation point setup) Select setting item "TGP" by pressing “Dec(-)” or “Inc(+)” button, then press “Enter” key and the initial value of “TGP” will blink. Use “Dec(-)” or “Inc(+)” button to adjust the operation point. (Note: In the interface of adjusting the value, return to the initial value "30" by pressing “Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.
Duty ratio (DTY) -3 ~ 0 ~ +3 Initial value; 0 6. (Steering mixing setup) Select setting item "STM" by pressing “Dec(-)” or “Inc(+)” button, then press “Enter” key and the initial value of “STM” will blink. Use “Dec(-)” or “Inc(+)” button to adjust the steering mixing range. (Note: In the interface of adjusting the value, return to the initial value "OFF" by pressing “Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.
exponential, which adjusts the whole throttle movement into a curve, throttle acceleration simply "jumps" away from neutral and then leaves the remaining response linear. Setup item FWRD:Forward side acceleration amount BRAK:Brake side acceleration amount Throttle acceleration adjustment Enter the function menu and use “Dec(-)” or “Inc(+)” button to access ACCEL function, then press “Enter” button to get into ACCEL function interface. 1.
acceleration amount. (Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.) Press “Enter” button, the adjusted value stops blinking, now the value has been set. "0":No acceleration "100":Maximum acceleration (Brake side maximum steering angle) Brake side acceleration amount(BRAK) 0~100 Initial value: 0 3. When ending setting, return to the initial screen by pressing “Exit” button twice.
(Note: In the interface of adjusting the value, return to the initial value "0%" by pressing “Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.) Press “Enter”button, the adjusted value stops blinking, now the value has been set. 4.When ending setting, return to the initial screen by pressing “Exit” button twice. Subtrim "SUBTR" Servo center position fine adjustment Use this function to adjust the neutral position of the steering, throttle and channel 3 servos.
6.When ending setting, return to the initial screen by pressing “Exit” button twice. Servo Reverse "REV" Servo operation reversing This function reverses the direction of operation of the servos related to transmitter steering, throttle, and channel 3 operation. Channel ST:Steering TH:Throttle CH3:Channel3 1.Enter the function menu and use “Dec(-)” or “Inc(+)” button to access REV function. 2.Press “Enter” button to get into REV function interface. 3.
Setup Item Steering D/R RATE Throttle D/R RATE Steering D/R rate (RATE) 0~100% Initial value: 100 Throttle D/R rate (Throttle D/R RATE) 0~100% Initial value: 100 1.Enter the function menu and use “Dec(-)” or “Inc(+)” button to access D/R function. 2.Press “Enter” button to get into D/R function interface. 3. Use “Dec(-)” or “Inc(+)” button to select Steering D/R RATE, press “Enter” key, and the initial value of Steering D/R RATE will blink. Use “Dec(-)” or “Inc(+)” button to make adjustments.
Setup Item RATE:Brake amount Brake amount (RATE) 0~100% Initial value: 100% 1.Enter the function menu and use “Dec(-)” or “Inc(+)” button to access ATL function. 2.Press “Enter” button to get into ATL function interface. 3.Press “Enter” key, and the initial value of RATE will blink. Use “Dec(-)” or “Inc(+)” button to adjust the value. (Note: In the interface of adjusting the value, return to the initial value "100%" by pressing “Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.
1.(Master channel) Channel selection (MST) ST, TH, CH3 Initial value: ST Select setup item "MST" by pressing “Dec(-)” or “Inc(+)” button, press “Enter” button, the initial master channel will blink. Use “Dec(-)” or “Inc(+)” button to select the master channel you wish to adjust, press “Enter”button, the blinking master channel you selected will stop blinking. 2.
Mixing amount -100~0~+100 Select the setting item "RGHT", "BRAK", or "DOWN" ( These setup items are different depend on the master channel. ST: "RGHT"; TH: "BRAK"; CH3: "DOWN" ) by pressing “Dec(-)” or “Inc(+)” button . Press “Enter” key, the initial value of "RGHT", "BRAK", or "DOWN" will blink, Use “Dec(-)” or “Inc(+)” button to adjust the right, brake, or down side mixing amount.
Setup Item POSI: Channel 3 position MODE: the 3rd channel “CH3 SWITCH” or “MENU SET” CH3:Channel 3 subtrim Channel 3 position (POSI) -100~+100 Initial value: 0 1.Enter the function menu and use “Dec(-)” or “Inc(+)” button to access CH3 function. 2.Press “Enter” button to get into CH3 function interface. 3.Use “Dec(-)” or “Inc(+)” button to select MODE setup item. If the initial MODE setup item is “CH3 SWITCH” .
Model name"NAME" RC3S stores model memories for five models.Each model memory can be named separately according to user’s requirement. Factory default name: MODEL5 1.Enter the function menu and use “Dec(-)” or “Inc(+)” button to access NAME function. 2.Press “Enter” button to get into NAME function interface,the first character of current name will blink, and the blinking character can be reset.
Be sure to reset Press “Enter” key, the symbol “YES” will stop blinking, and return to the initial screen. Now the model data is reset to the initial setting that is the default value set at the factory. Not to reset Press “Dec(-)” or “Inc(+)” button, the symbol “YES” will stop blinking and the symbol “NO” will blink, press “Enter” key, the symbol “NO” will stop blinking, return to the initial screen by pressing “Exit” button twice. Or you can press “Exit” button twice to quit resetting directly.
