Shields ® Avoidance Solutions Indoor Micro Shields Owner’s Manual Please read this entire guide before operating. www.invisiblefence.
Important Precautions • Invisible Fence® Brand pet containment systems have contained over two million pets. However, there are some precautions you should take. • Read and retain manuals: Read the entire Owner’s Manual before using your new Indoor Micro Shields® solution. If you have any questions after reading this manual, call your Invisible Fence® Brand dealer. • Adhere to all warnings and cautions contained in any Invisible Fence® Brand manual.
Congratulations on your purchase of the Indoor Micro Shields® solution. Please read and review this entire manual to become familiar with Indoor Micro Shields® solution components and its operation. It is strongly recommended you review this information before using the product. The Indoor Micro Shields® solution gives you control over the areas a pet or pets have access to inside your home.
Components How the System Works Indoor Micro Shields® Transmitter The transmitter is the heart of the system. It is placed in areas you want to protect from your pet, or protect your pet from. The lightweight, portable design is easy to use and powered by a rechargeable battery pack. You may use the included AC adapter for locations near an electrical outlet. The adapter is also used for charging* the transmitter. The transmitter sends a signal field up to 4feetin diameter or as a 2 foot radius.
Operating Guide Important: To ensure your pet does not receive an unintended correction, make sure your pet is not wearingthe Computer Collar®unit when turning ON or adjusting the Indoor Micro Shields® transmitter. 1. Charging • To charge the battery, plug one end of the AC adaptor (RAC00-13701) into a standard wall outlet and the other end into the power jack located on the edge of the Indoor Micro Shields® transmitter. • Allow the unit to charge a full 4 hours before first use.
Operating Guide 4. Changing the Channel Setting on the Indoor Micro Shields® transmitter 1. Press and release the RANGE DOWN (-) button until no bars appear on the LCD. 2. Turn the unit over and remove the bottom lid by rotating counter-clockwise. 3. Locate the switch for the Channel (A), Channel (B) and Channels (A+B). (Figure 1) 4. Select the desired setting. Note: The Indoor Micro Shields® transmitter will not enter into programming mode if this switch is set to A+B. 5.
Operating Guide Multi-Area Shielding Your Indoor Micro Shields® Transmitter and the Computer Collar®unit are preset to operate on Channel A (CH.A). For homes with two or more pets, this setting is usually sufficient as long as all pets are required to avoid the same protected areas like keeping all pets away from the trash, off the counter tops off the sofa, etc. In some multi-pet homes, it may be desired to allow one pet access to an area while denying access to another pet. • When set to Channel A (CH.
Training Guide For pets trained to the Invisible Fence®Brand system • Use Invisible Fence®Brand training flags to mark the outside of the signal field range. This gives your pet a visual marker, similar to how they learned the signal field range of the outdoor pet containment system. • Allow your pet to enter the protected area. By already being familiar with the training flags and the warning beep, your pet should react immediatelyby moving away from the protected area.
Troubleshooting Indoor Micro Shields®does not appear to work • Check for low battery (audible chirp once every 30 seconds and flashing LCD). If low battery is indicated, plug the AC adapter into the unit and charge for 2 hours. • Check/replace the Power Cap® Battery in the Computer Collar®unit. • The Indoor Micro Shields® transmitter power could be completely drained. Apply power to the Indoor Micro Shields® transmitter using the AC adapter to verify operation.
Battery Disposal Separate collection of spent batteries is required in many regions; check the regulations in your area before discarding spent batteries. The Computer Collar®unit operates on one (1) Lithium (Li-MnO2) battery with a 3 Volt, 160 mAh capacity, replace only with equivalent battery that may be obtained from your Invisible Fence® Brand dealer. The transmitter operates on 1 rechargeable Lithium Ion Polymer (Li-ion) battery pack with a 3.7 Volt, 420 mAh capacity.
Compliance US and Canada FCC ID: KE3-3002563 IC: 2721A-3002563 This device complies with Industry Canada rules. This device complies with part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Dealer Name: Dealer Phone: System Frequency: Notes: 800-578-3647 (USA) (865) 777-5404 (International) ©2012 Radio Systems®Corporation Need to remove the symbol here. All rights reserved. Protected by Patents: U.S.: 7,046,152; 7,068,174; 7,204,204; 7,278,376; 7,495,570 www.invisiblefence.