Model V10 Mobile Satellite TVAntenna with FastFind Remote Installation and Operating Manual MADE IN THE U.S.A. 1. INTRODUCTION ...........................................................................2 2. BACKGROUND .............................................................................3 3. COMPONENT OVERVIEW and SPECIFICATIONS......................4 4. FCC USER’S INFORMATION .......................................................5 5. INSTALLATION ...................................................
Introduction Congratulations on your purchase of the Vu Qube V10. The Vu Qube V10 is equipped with a FastFind remote enabling you to quickly position the Vu Qube antenna from inside your vehicle. The Vu Qube V10 is compatible with any service provider including DIRECTV®, DISH Network® or Bell ExpressVu.
Background Satellites used for television signals are 22,300 miles (37,000 km) above the earth’s equator. The purpose of the Vu Qube is to acquire the signal traveling that great distance and transmit the signal to the digital receiver in your vehicle, so you can watch TV anywhere you park. Satellite television, like other communications relayed by satellite, starts with a transmitting antenna located at an uplink facility on Earth.
Vu Qube V10 Component Overview Manual Quick Reference Guide Vu Qube FastFind Remote Vu Qube Antenna RG6 Coaxial Cable (20a) Mounting Kit (Purchased Separately) Kit shown is Model Number 31100 ***You will need to supply your own fasteners to attach a Vu Qube bracket to your vehicle.
FCC User Information Main Components Vu Qube V10 Antenna Vu Qube V10 Remote Part #: VQV10 FCC ID: UUM10156V10 IC: 6873A -10156V10 Part #: VQV10R FCC ID: UUM10157V10 IC: 6873A -10157V10 This device complies with Part 15 of THE # RULES /PERATION IS SUBJECT TO the following two conditions: 1) This device must not cause harmful interference, and 2) This device must accept interference received including interference that may cause undesired operation.
Installation Overview of Installation s 4HE 6U 1UBE IS DESIGNED TO BE MOUNTED TO A VEHICLE &IGURE s )NSTALL WITH COAXIAL CABLE CONNECTOR FACING SIDE OF VEHICLE YOU WILL RUN coaxial cable. s )T IS RECOMMENDED TO INSTALL THE 6U 1UBE WITH A MINIMUM OF q of the top cover above the highest point of the cab or air shield (Figure 1) and away from interfering objects like smoke stacks. s 4HE COAXIAL CABLE NEEDS TO ENTER THE #AB TO BE CONNECTED TO THE SATELLITE receiver. Figure 1.
Installation (continued) Mounting the bracket and selecting location to run wiring ./4% )NSTRUCTIONS FOR MOUNTING THE 6U 1UBE IS ILLUSTRATED IN THIS MANUAL using Mounting Bracket Kit part number 31100. This Mounting Bracket Kit and others were designed specifically to mount the Vu Qube to the back of a truck cab. Please contact Wallace Technologies, LLC (866-802-2228) regarding other bracket options. 1.
Installation (continued) 2. Drill holes for mounting bracket with proper size depending on fasteners used. ./4% The installer is responsible for determining the most appropriate fastener to secure the bracket to the cab. Depending on the cab material, fasteners such as lag screws, well nuts, sheet metal screws, toggle bolts and T anchors may be used. Fasteners should always be used in combination with compatible sealant to environmentally seal the holes after installation. 3.
Installation (continued) Wiring 1. Connect 20a coaxial to Vu Qube. 2. Pass 20a coaxial cable through hole previously drilled. ./4% It is an option to run the wiring down the back of the cab and up into the cab through an access bay. 3. Connect coaxial cable from Vu Qube to SATELLITE IN port on satellite receiver. 4. Make sure satellite receiver is connected to TV per manufacturer’s instructions.
Vu Qube V10 Operation s )-0/24!.4 #,%!2 ,).% /& 3)'(4 FOR 6U 1UBE !NTENNA TO THE SOUTHERN SKY REQUIRED. Physical obstruction (i.e., smoke stacks, buildings, trees, telephone poles, etc.) can block the satellite signal from reaching the antenna. s 3ATELLITE 46 AND RECEIVER TECHNOLOGY ARE CONSTANTLY CHANGING If you experience difficulty contact (866) 802-2228. Finding the Satellite and Acquiring a Signal ./4% 3ATELLITE 2ECEIVER AND 46 -534 BE /. 1.
Satellite Position Memory TO STORE POSITION: Hold down either the Satellite 1 or Satellite 2 button for at least 2.5 seconds. The LCD will show “P1” or “P2” when button is released. TO RECALL POSITION: Hold down either the Satellite 1 or Satellite 2 button for less than 2.5 seconds. The LCD will show “r1” or “r2”. TO CANCEL RECALL: Press any arrow button to stop moving to a stored position.
Maintenance The Vu Qube has been designed to be maintenance and trouble free. For optimum signal strength, keep the cover clean from dirt, bugs, and other debris. Periodic washing of the top cover with mild soap and water is recommended. If you plan on storing your vehicle for long periods of time, it is recommended that the system be put through a search procedure on a quarterly basis to keep all moving parts in good working order.