User's Manual

ManualsBrandsRadicom Research ManualsElectronicsBluetooth Module

Table Of Contents

Table of Contents
Important Regulatory Compliance and User Information 8
Introduction
Features
Model and Ordering Information
Important Regulatory Compliance and User Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF Exposure compliance. The end user should NOT be provided any instructions on how to remove or install the device. The users manual for end users must include the following information in a prominent location
FCC RF Radiation Exposure Statement
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, this device must not be co-located or operating in conjunction with any antenna or transmitter. This device contains a low power transmitter. When this device is operational, use only with the supplied, or recommended antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. Changes or modifications not expressly approved by the manufacturer or party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for assistance.
IC (Industry Canada) Statement:
“This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device”
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de license. L’exploitation est autorisee aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit acceptor tout brouillage radioelectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.
CE Declaration of Conformity
_
For the following equipment:
are herewith confirmed to comply with the requirements set out in the Council (European parliament) Directive on the Approximation of the Laws of the
Member States relating to Electromagnetic Compatibility of Radio and Telecom device (1999/5/CE). For the evaluation regarding this Directive, the following
standards were applied:
EN 61000-3-2:2006+A2:2009, EN 300 328 V1.7.1, EN 62311: 2008,
EN 301 489-1, V1.8.1, EN 61000-3-3:2008, EN 301 489-17 V2.1.1
________________________
This equipment is marked with the and can be used throughout the European community.
France – 2.4GHz for Metropolitan France:
In all Metropolitan departments, wireless LAN frequencies can be used under the following conditions, either for public or private use:
 Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band
Europe – R&TTE Compliance Statement:
Hereby, Radicom Research Inc. declares that this equipment complies with the essential requirements and other relevant provisions of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE).
RB4000 Mechanical Diagram (inches) & Pin Assignments
RB4000MB Carrier Board RS232 DB 9 Pin Definitions
LED Operation
Connecting to Your System
- Warranty Coverage and Duration
Contacting Radicom Research
http://www.radi.com/

Radicom Research, Inc.

Designers Guide for the

RB4000

H4000CE

RB4000HM

MDK4000 Kit

RoHS Serial TTL Bluetooth Modules

RB4000 RB4000HM

RoHS Compliant

April 18, 2012

Summary of content (20 pages)

PAGE 1
Radicom Research, Inc.
PAGE 2
Table of Contents Introduction 3 Features 4 Specifications 5 Model and Ordering Information 6 FCC& IC Label and Model Identification 7 Important Regulatory Compliance and User Information 8 CE Declaration of Conformity 10 Layout Design Suggestions 10 RB4000 Pad Size 11 RB4000 Mechanical Diagram & Pin Assignments 12 RB4000 Interface Signal Level Definitions 13 RB4000HM Mechanical Diagram & Pin Assignments 14 RB4000HM Switch settings 15 RB4000HM Interface Signal Level Definitions 15
PAGE 3
Introduction Thank you for purchasing Radicom Research’s RB4000 Bluetooth Module. We are committed to providing you quality service and technical support. The RB4000 and RB4000HM Bluetooth modules are designed to meet OEM’s needs of embedding shortrange wireless data connectivity to their products. The RB4000 family offers a quick and simple solution for wireless point-to-point Bluetooth communications.
PAGE 4
Features • • • • • • • • • • • • • • • • • • Bluetooth 2.0+EDR support Small sizes: 0.57” x 1.26” x 0.08” (RB4000) or 1” x 1.26” x 0.2” (RB4000HM) Class 2 radio, 4dBm transmission power Serial Port Profile (SPP) support Secure simple pairing support Link Data Rate 2.1Mbps Max SPP/ UART data rates: 115.
PAGE 5
Specifications Dimensions RB4000: 0.57”x1.26”x0.08” ????? RB4000HM: 1” x 1.26” x 0.2” ?????? Device Type Embedded Bluetooth OEM module Interface Serial Data Link Protocol Bluetooth 2.0+EDR Frequency ISM 2.4 GHz short-range radio frequency band Frequency Range 2,402 – 2,483.5 MHz Max Transmit Power +4dBm Receive Sensitivity -89dBm Bluetooth Class Class 2 Link Data Transfer Rate 2.1Mbps Max UART /SPP Data Transfer Rate 115.
PAGE 6
Model and Ordering Information Model Number Description RB4000 or 0.57" x 1.26" x 0.08" surface mount, short range Bluetooth module with on-board antenna Model: RB4000 The RB4000 is the same as the H4000CE. The name is different for marketing purposes only. H4000CE Available as either SPP-A Initiator and SPP-B Acceptor Bluetooth module RB4000HM (-a + -c) 1.0" x 1.26" x 0.2" dual-in-line, through-hole Bluetooth module Model: RB4000HM-a - PCB antenna on-board. Model: RB4000HM-c - With on-board U.
PAGE 7
ATN-2d-RP-SMA Replacement antenna, 2.4GHz, 2dBi, RP-SMA, Omni-directional. AC6i-RP-SMA 6" U.FL. to RP-SMA female connector antenna cable FCC & IC Label and Model Identification The RB4000 module family is FCC Part 15 and IC (Industry Canada) certified. The RB4000 is also CE marked. The modules are labeled with the appropriate RB4000 module model number and FCC Part 15 ID, IC registration number and CE mark. The label can be found on top of the metal shielding on the RB4000 Module. Radicom Research Inc.
PAGE 8
Important Regulatory Compliance and User Information The final product with the modules installed needs to be tested for FCC Part 15, IC (Industry Canada) CE, EMI/RFI compliance. Radicom certification documentation will help streamline the final product approval process. Contact Radicom for more information. To maintain compliance in the finished product, carefully follow guidelines in this section.
PAGE 9
End User Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF Exposure compliance. The end user should NOT be provided any instructions on how to remove or install the device.
PAGE 10
CE Declaration of Conformity For the following equipment: Radicom Research Inc. Bluetooth Module Model(s): RB4000, H4000CE, RB4000HM-a, and RB4000HM-c are herewith confirmed to comply with the requirements set out in the Council (European parliament) Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility of Radio and Telecom device (1999/5/CE).
PAGE 11
2. 3. 4. The bigger Antenna clearance area, the better. The Antenna itself needs to stay away from any circuit or component at least 2mm. Antenna clearance area means Top and Bottom both required to be cleared. Do not use metal materials on design where near Antenna area. For example, battery snaps, USB connector, iron case, etc. For RB4000HM-c model (external antenna type), when RF trace meets a turning point, try to make the RF trace as smooth as you can’t use right angle trace.
PAGE 12
RB4000 Mechanical Diagram (inches) & Pin Assignments 12
PAGE 13
RB4000 Interface Signal Level Definitions Note: I/O is DTE not DCE. RTS and CTS functionality is for Hardware Flow Control.
PAGE 14
RB4000HM Mechanical Diagram & Pin Assignments Notes: 1. Pin spacing is 0.100 inch from center to center. 2. Suggested mating female connector: Samtec P/N. #SSW-110-21-G-S (RoHS Thru-Hole) Samtec P/N. #SSW-110-22-G-S-VS (RoHS SMT) 3. Square pins - 0.025" x 0.
PAGE 15
RB4000HM Switch settings: This Switch is reserved for future use. Do not change. They all should be set to the OFF position. DTE Speed 115200 (Default) 1 OFF 2 3 OFF OFF RB4000HM Interface Signal Level Definitions Pin # Pin Name 1 KEY 2 Not Used 3 LINK LED Type O 4 5 3.
PAGE 16
RB4000MB Carrier Board RS232 DB 9 Pin Definitions The pin definitions of DB9 used on the RB4000MB RS232 Serial Connector are as follows: 1. 2. 3. 4. 5. 6 7. 8. 9. DCD: RXD: TXD: DTR: GND: DSR: RTS: CTS: RI: Input, Carrier Detect Input, Received Data Output, Transmit data Output, Data Terminal ready Ground Input, Data Set Ready Output, Request to Send Input, Clear to Send Input, Ring Indicator LED Operation The modules have an On Board LED to indicate the Bluetooth Connection Status.
PAGE 17
Connecting to Your System NOTE: Do Not Plug in the USB cable and AC power adapter at the same time. Only use one or the other. Plugging in both the USB cable and AC power adapter may damage the USB port on your PC or USB device. Below is a simple example to show how the Radicom Bluetooth modules work. This example demonstrates how the Bluetooth Modules can connect to each other. 1. RB4000MB-SPP-A Initiator setup: Open HyperTerminal and select an available Serial Comport.
PAGE 18
Limited Warranty Warranty Coverage and Duration Radicom Research, Inc. (“RRI”) warrants to the original purchaser its RRI-manufactured products (“Product”) against defects in material and workmanship under normal use and service for a period of one year from the date of delivery. During the applicable warranty period, at no charge, RRI will, at its option, either repair, replace or refund the purchase price of this Product, provided it is returned in accordance with the terms of this warranty to RRI.
PAGE 19
How to Receive Warranty Service: To obtain warranty service, contact RRI by phone (408)-383 9006 for RMA Department or email to rma@radi.com for an RMA (Return Merchandise Authorization) number. Deliver or send the Product, transportation and insurance prepaid to RRI, with the RMA number clearly marked on the outside of the package. General Provision This warranty sets forth the full extent of RRI’s responsibilities regarding the Product.
PAGE 20
Contacting Radicom Research If more information or technical support is needed, please contact us: 2148 Bering Drive San Jose, CA. 95131 Telephone: (408) 383 9006 Fax: (408) 383 9007 or e-mail: sales@radi.com http://www.radi.