Radicom Research, Inc.
Table of Contents Introduction 3 Features 4 Applications 5 Specifications 6 Electronic Character 7 Model and Ordering Information 7 Layout Design Considerations 8 BPM2001 SMD Module Mechanical Diagram & Pin Assignments 9 BPM2001 SMD Module Interface Signal Definitions 10 BPM2001-HM Mechanical Diagram & Pin Assignments 12 BPM2001-EK Switches & Connector Functional Descriptions 16 Operating the BPM2001-EK Evaluation Kit 17 BPM2001-MB Carrier Board RS232 DE-9 Pin Definitions 17 FCC &
Introduction Radicom BPM2001 is a single chip based radio and baseband for Bluetooth v4.0 systems and Bluetooth low energy. With host software, BPM2001 provides a system fully qualified to the Bluetooth v4.0 specification for data and voice applications.
Features • Fully qualified Bluetooth Bluetooth® v4.0 system • Full-speed Bluetooth operation with full piconet and scatternet support • Class 2 Bluetooth power level supported • High-sensitivity Bluetooth receiver • Wideband speech • SBC encoding • Low-power selectable 1.2 to 3.6V I/O • Full-speed USB 2.0 interface • High-speed UART port (up to 4Mbps) • 2 x PCM/I2S digital audio interfaces • Support for IEEE 802®.
Applications • Industrial • Medical • For AP Switch, Router, PC, NB, PND, PDA, Mobile devices, USB dongle 5
Specifications Dimensions 27.94mm x 16.51mm x 2.20mm (BPM2001) 83.73mm x 66.11mm (BPM2001HM) Device Type Embedded Bluetooth OEM modules Interface Serial UART / PCM / I2S / USB Data Link Protocol Bluetooth 4.0 Frequency 2.402 – 2.480 GHz Transmit Power 6 dBm (typical) Receiver Sensitivity -92.5dBm (typical) Bluetooth Class Class 2 Range Up to 10 meters Security 128-bit encryption (optional) Power Consumption IDE: 3~6mA / Play: 22~38mA Power Supply Voltage 1.8V~ 3.
Electronic Character Operation voltage Minimum Typical Maximum Unit 1.8 3.3 3.6 V Output Power 6 dBm Sensitivity -84 dBm active mode, VBAT=3.3V 24 mA Model and Ordering Information Model Number Description BPM2001 Surface mount, class 2, Bluetooth HCI module with on-board antenna BPM2001-HM BPM2001HM-a: DIP, through hole module with on-board antenna. BPM2001HM-c: DIP, through hole module with U.
Layout Design Suggestions • General Layout Rules- All Printed Circuit Boards must comply with UL94V0 standard for flammability. Always use RoHS compliant Parts and materials. • Suggestions for Layout: 1. Do not place Power circuit, X’tal, Inductor, etc near RF area. 2. The bigger Antenna clearance area, the better. The Antenna itself needs to stay away from any circuit or component at least 2mm. Antenna clearance area means Top and Bottom both required to be cleared. 3.
BPM2001 SMD Module Mechanical Diagram & Pin Assignments Top side view: Board size = 27.940 mm x 16.510 mm Pitch of short and long side = 1.905 mm Pad width = 1.524 mm x 1.000 mm Module Height Maximun height = 2.2 mm Board thickness = 0.
BPM2001 SMD Module Interface Signal Definitions Pin# Pin Name Type Description I/O Voltage Range 01 GND Power System ground --- 02 GND Power System ground --- 03 GND Power System ground --- 04 /PCM_SEL I High switches SPI/PCM lines to SPI, low switches SPI/ PCM lines to PCM/PIO use. Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.4 VDD 05 UART_CTS I UART clear to send, active low Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.4 VDD Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.
Pin# Pin Name Type I/O Voltage Range Description Voh: 0.75 X VDD Vol: 0 – 0.4V Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.4 VDD Voh: 0.75 X VDD Vol: 0 – 0.4V Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.4 VDD 18 GPIO1 I/O Programmable input/output line 19 GPIO0 I/O Programmable input/output line 20 GND Power System ground --- 21 GND Power System ground --- 22 /RESET I Active low system reset 23 USB_5V_IN I Input to USB regulator. Connect to external USB bus supply, e.g.
BPM2001-HM Mechanical Drawing & Pin Assignments 12
BPM2001-HM Interface Signal Definitions P3 Port Pin Assignments Pin# Pin Name Type Description Voltage Range 1 GPIO_5 I/O I/O port power input Voh: 0.75 X VDD Vol: 0 – 0.4V Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.4 VDD 2 /PCM_SEL I High switches SPI/PCM lines to SPI, low switches SPI/ PCM lines to PCM/PIO use. Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.4 VDD 3 SPI_MOSI I SPI data intput/PCM1 port synchronous data input Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.
Pin# Pin Name Type Description Voltage Range 19 GND Power System ground --- 20 GND Power System ground --- 21 GND Power System ground --- 22 GND Power System ground --- 14
P1 Port Pin Assignments Pin# Pin Name Type Description 1 UART_CTS I UART clear to send, active low 2 UART_RTS O UART request to send, active low 3 VDD I HM Power In 4 UART_TXD O UART data output, active high 4 UART_RXD I UART data input, active high 6 GND Power System ground Voltage Range Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.4 VDD Voh: 0.75 X VDD Vol: 0 – 0.4V Input voltage: 4.30V – 5.75V Voh: 0.75 X VDD Vol: 0 – 0.4V Vih: 0.7 X VDD – VDD + 0.4V Vil: -0.4V -- 0.
Operating the BPM2001-EK Evaluation Kit The BPM2001-MB Evaluation PCB has white silkscreen legend located by the switches and connectors described below. 5 8 4 7 3 2 1 6 9 1. 2. 3. 4. 5. 6. 7. 8. 9. USB 5V slot (USB1) Main board power switch (S5) UART enable/disable switch (S6) RS232 male DE-9 connector (J7) BPM2001-HM carrier board with module UART and power interface header (P1) HM board power switch only for 1.
Operating the BPM2001-EK Evaluation Kit -On PC (Master): 1. Connect UART cable to PC com port and supply power 2. Execute "cmd" under Windows 3. cd "c:\Program Files\CSR\BlueSuite 2.4.8" 4. btcli com1 bcsp 115200 5. Verify "command_status pending nhcp:0x01 nop" 6. Type "rbn" and verify displayed strings (8 lines) 7. Type exec "d:\d-drive\gps\csr8311\8311.btcli" 8. Wait for "*** HCI TRANSPORT FAILED ***" 9. Type "restart" 10.Verify "command_status pending nhcp:0x01 nop" 11.Type "i" to start inquiry 12.
FCC & IC Label and Model Identification The BPM2001 module family is FCC Part 15 and IC (Industry Canada) certified. The BPM2001 is also CE marked. The modules are labeled with the BPM2001 module model number and FCC Part 15 ID, IC registration number and CE mark. The label can be found on top of the metal shielding on the BPM2001 Module. Radicom Research Inc.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna, As long as 1 condition above is met, further transmitter test will not be required.
Industry Canada statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
End Product Labeling The final end product must be labeled in a visible area with the following: “Contains IC:2377ABPM2001”. Plaque signalétique du produit final Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 2377A-BPM2001".
CE Declaration of Conformity For the following equipment: Radicom Research Inc. Bluetooth Module Model(s): BPM2001 are herewith confirmed to comply with the requirements set out in the Council (European parliament) Directive on theApproximation of the Laws of the Member States relating to Electromagnetic Compatibility of Radio and Telecom device (1999/5/CE). For the evaluation regarding this Directive, the following standards were applied: EN 300 328 V1.8.1 EN 301 489-1 V1.9.2 EN 301 489-17 V2.2.
Limited Warranty Warranty Coverage and Duration Radicom Research, Inc. (“RRI”) warrants to the original purchaser its RRI-manufactured products (“Product”) against defects in material and workmanship under normal use and service for a period of one year from the date of delivery. During the applicable warranty period, at no charge, RRI will, at its option, either repair, replace or refund the purchase price of this Product, provided it is returned in accordance with the terms of this warranty to RRI.
How to Receive Warranty Service: To obtain warranty service, contact RRI by phone (408)383-9006 for your sales representative or email to sales@radi.com for an RMA (Return Merchandise Authorization) number. Deliver or send the Product, transportation and insurance prepaid to RRI, with the RMA number clearly marked on the outside of the package. General Provision This warranty sets forth the full extent of RRI’s responsibilities regarding the Product.
Contacting Radicom Research If more information or technical support is needed, please contact us: 2148 Bering Drive San Jose, CA. 95131 Telephone: (408) 383 9006 Fax: (408) 383 9007 or e-mail: sales@radi.com http://www.radi.
