User's Manual Part 3

ManualsBrandsR-tron ManualsElectronicsiDEN Add-On Filter Box

iDEN Add-On Filter Box

User’s Manual -19-

3.5 Bandwidth & Band Setup

The bandwidth and band setup for filtering a downlink signal is done easily

by the dip switches located at the bottom of iDEN Add-On Filter Box.

The software and computer are not required.

A user can setup the bandwidth and band referring to an index table for the

combination of the dip switch printed on the right side of the iDEN Add-On

Filter Box.

For 800MHz’s only, the bandwidth setup is required.

For 800MHz’s and 900MHz’s, the band setup is required.

Figure 14. Dip Switches for Bandwidth and Band Setup

Figure 15. Index Table for Bandwidth and Band Setup

The bottom of the Equipment

he ri

ht side of the e

men

Summary of content (12 pages)

PAGE 1
iDEN Add-On Filter Box 3.5 Bandwidth & Band Setup The bandwidth and band setup for filtering a downlink signal is done easily by the dip switches located at the bottom of iDEN Add-On Filter Box. The software and computer are not required. A user can setup the bandwidth and band referring to an index table for the combination of the dip switch printed on the right side of the iDEN Add-On Filter Box. For 800MHz’s only, the bandwidth setup is required. For 800MHz’s and 900MHz’s, the band setup is required.
PAGE 2
iDEN Add-On Filter Box a. For 800MHz, a.1. Bandwidth Setup a.2. Band Shifting for 18MHz Bandwidth a.3. Band Shifting for 7MHz Bandwidth 7B FS 2 862~869MHz 862~869MHz 861.8~868.8MHz 861.6~868.
PAGE 3
iDEN Add-On Filter Box b. For 900MHz’s 3.6 Power Up a. Connect the power cord. b. Plug the power cord into a wall outlet. c. Switch on. d. Check if the green LED at the bottom turns on. Figure 16.
PAGE 4
iDEN Add-On Filter Box 4. Troubleshooting 4.1 RF Connection Check Problem Filtered Output Power (=Input Power to the repeater) is too weak. Solution Check if the following RF connections are loose: 1. The cable connection from the donor antenna port to Input port 2. The cable connection from the Filtered output to the repeater 4.2 Power Connection Problem All LEDs at the bottom are turned off. Figure 17.
PAGE 5
iDEN Add-On Filter Box Figure 18. AC power cord Check 4.3 Red Light on the Alarm LED Problem Red light LED turns on the Alarm LED after applying AC power. Figure 19. Red Light on Alarm LED Solution Request a technical support.
PAGE 6
iDEN Add-On Filter Box iDEN Add-On Filter Box Copyright © R-tron Inc. 2000-2007 All Rights Reserved 6042, College Boulevard, Overland Park, KS 66211 Any reproduction, distribution, or revision of any or all portions of this manual is prohibited without written permission from R-tron Inc. The information in this guide is subject to change without any prior notification. www.r-tron.
PAGE 7
LIMITED WARRANTY STATEMENT 1. WHAT THIS WARRANTY COVERS: LG offers you a limited warranty that the enclosed subscriber unit and its enclosed accessories will be free from defects in material and workmanship, according to the following terms and conditions: (1) The limited warranty for the product extends for ONE (1) year beginning on the data of purchase of the product.
PAGE 8
For Your Safety Important Information This user guide contains important information on the use and operation of this phone. Please read all the information carefully for optimal performance and to prevent any damage to or misuse of the phone. Any changes or modifications not expressly approved in this user guide could void your warranty for this equipment.
PAGE 9
For Your Safety ] Unplug the power cord and charger during lightning storms to avoid electric shock or fire. ] When riding in a car, do not leave your phone or set up the hands-free kit near to the air bag. If wireless equipment is improperly installed and the air bag is activated, you may be seriously injured. ] Do not place any heavy items on the power cord. Do not allow the power cord to be crimped as it may cause fire or electric shock.
PAGE 10
For Your Safety FCC RF Exposure Information Body-worn Operation WARNING! Read this information before operating the phone. This device was tested for typical body-worn operations with the back of the phone kept 0.79 inches (2.0cm) between the user’s body and the back of the phone. To comply with FCC RF exposure requirements, a minimum separation distance of 0.79 inches(2.0cm) must be maintained between the user's body and the back of the phone.
PAGE 11
For Your Safety Vehicle Mounted External Antenna (optional, if available) A minimum separation distance of 8 inches (20cm) must be maintained between the user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure requirements. For more information about RF exposure, visit the FCC website at www.fcc.gov FCC Part 15 Class B Compliance This device and its accessories comply with part 15 of FCC rules.
PAGE 12
FCC RF Exposure Information Finding Stored Phone Numbers WARNING! The antenna used for this transmitter must not exceed 2.5dBi and must be installed to provide a minimum separation distance of 20 cm from all persons. CAUTION Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations. Do not use the phone with a damaged antenna.