UNI FLAME AUTOLIFT PLASMA CUT40 Inverter Air Plasma Manual MILD STEEL 240 Volt MAXIMUM CUTTING CAPACITY 10MM Plasma CUT
UNI FLAME AUTOLIFT 2YEARS Warranty * Machine Model Description Plasma Cut 40 Part Number KUPJR40 CONTENTS PAGE No: Safety 3 General Description 4 Curcuit Diagram 5 Main Parameter 6 Installation & Operation 7 Regulator Installation 8 Operation 9 Spare Parts List - Machine 10 Spare Parts List - Torch 11 Maintenance 12 Trouble Shooting 12 EC DECLARATION OF CONFORMITY Hereby we declare that our machines for industrial and professional use as stated below: Type: CUT40 Conform the EMC
SAFETY Welding and cutting equipment can be dangerous to both the operator and people in or near the surrounding working area, if the equipment is not correctly operated. Equipment must only be used under the strict and comprehensive observance of all relevant safety regulations. Please read and understand this instruction manual carefully before the installation and use/operation of this equipment. not switch the function modes while the machine is operating.
UNI FLAME AUTOLIFT 2. GENERAL DESCRIPTION & SAFEGUARDS The plasma cutting unit generates constant current and has been designed to cut metals. The cutting process is carried out through the melting of the metal caused by high temperature created by the electric arc between the torch electrode and the base metal. The molten material is removed by a high-speed jet of ionized gas (compressed air is the type of gas used). This cutting machine is manufactured with advanced inverter technology.
Single Phase Input UNI FLAME AUTOLIFT 3.
UNI FLAME AUTOLIFT MAIN PARAMETER Machine Model Description Part Number Plasma Cut 40 KUPJR40 Tecnical Specification Input voltage (V) Input Frequency (Hz) Input capacitance (KVA) No-load voltage (V) Current range (A) Output cutting voltage (V) Rated duty cycle (%) Efficiency (%) Power factor Insulation class Protection class Arc Starting Air flow (Litres/min) Compressed air pressure Max.
INSTALLATION AND OPERATION In order for the unit to function correctly, it must be installed properly. Follow the procedure given below for correct installation: 1 Read the safety rules given in this manual carefully. 2 Check on receiving the unit that there are no defective parts or parts damaged during transportation. 3 Attach air regulator as show in diagram Regulator Installation. 4 Set your unit up in an area which is adequately ventilated and make sure that the air vents are not obstructed.
UNI FLAME AUTOLIFT CAUTION: Do not point the torch jet at foreign bodies CAUTION: Avoid unnecessary lighting of the pilot arc to prevent excessive consumption of the electrode and nozzle. CAUTION: During cutting the speed of the torch movement should be in accordance with the thickness of the piece to be cut. Excessive speed causes a return of incandescent towards the torch which shortens the life of the parts of the torch most subject to wear and tear.
UNI FLAME AUTOLIFT OPERATION Of the torch CAUTION: Before inspecting or changing the parts of the torch, disconnect the power supply to the unit. Special tools are not required to replace torch parts. Simply unscrew the shield cup and all the components of the torch can easily be replaced. CAUTION: Unscrew the sheild cup only after the cooling air flow has stooped (the in observance of this precaution may damage the torch body) 1 Check the condition of the Electrode, Cutting tip and the Shield cup.
UNI FLAME AUTOLIFT 3 4 2 10 1 5 12 Spare Parts No 1 Description Front panel J02042 WGA Part No.
UNI FLAME AUTOLIFT 1a 5 3 4 12 13 10 11 9 2 Front end consumables Spare Parts No WGA Part No. 1 07035 Description 70° Torch head 3 07103 Handgrip complete with microswitch 4 52519/D Electrode - Hf 5 60050 Gas Distributor 6 51290 Tip - 35 Amp.
MAINTENANCE WARNING: Exposure to extremely dusty, damp, or corrosive air is damaging to the welding machine. In order to prevent any possible failure or fault of this welding equipment, clean the dust at regular intervals with clean and dry compressed air of required pressure.
