User Manual

2.Access the menu item “Setting”
( )and select “ Bike Meter ”.
4.Press the “Back”( ) button, it
will go back to “Bike Meter” page,
then you can see the two small icons
show up when connected.
1.Open the “Myway Fit” ( )app
on your smartphone and choose
the “Bike Meter”( ).
Pairing with BLE Bike Combo
Sensor
Bike Meter
90
RPM
63
BPM
FINISH
KPH
0
100
8040
20
60
CAL
kcal
12345
Training
Distance
500.0
km
ODO
m/h
225263
Training
60
90
120
150
180
Digital
Map
Setting
Home
History
Console
21:30:59
89
m
30
50
80
110
140
170
200
Connection
Bluetooth Smart
®
Heart Rate Monitor
Back
ON
ON
ON
ON
ON
Device
Speed(kph)
n/a
Cadance(rpm)
n/a
Bike Name:
Scanning
Forget Device
Save
BT003
paired
Connected
Bike 1
Circumference:
cir(200-3999)
mm
Connection
Bluetooth Smart
®
Heart Rate Monitor
Back
ON
ON
ON
ON
ON
Device
Speed(kph)
n/a
Cadance(rpm)
n/a
Bike Name:
Scanning
Save
BT003
Detected, not paired
Disconnect
Bike 1
Circumference:
cir(200-3999)
mm
SMART
Trip Sleep Tracker
Z
Z
Z
Bike MeterHeart Rate
My Weight
Settings
Password Lock Off
Profile
Activity & Sleep Tacker
Heart Rate Monitor
Bike Meter
Connection
About
Upgrade APP
Help / Information
Password
Health Scale
Back
Cadence Sensor
Tech: Bluetooth low energy technology
Battery lifetime (approx): 500 hours
Bettery: 1 x CR2032 (included)
Transmission range: ﹤3 meter (9.9ft)
Waterproof: splash proof
Operating temperature: -10ȭ~50ȭ (14ȯ~122ȯ)
Weight: 40g/1.41oz (bike combo sensor)
Bike Combo Sensor
Installation Procedure
Use the supplied cable ties to hold the sensor
in place. Do not fully tighten.Attach the magnet
to a spoke. Do not fully tighten.
Adjust the magnets and the sensors, making
sure the air gap between sensor markings and
magnets is less than 3mm. when setup is
complete,tighten the cable ties.
Combo sensor will transmit a pairing bit
when it tigger by wheel magnet or crank
magnet. The pairing bit will present after
a battery installation and it will last for 1
minute. Combo sensor will stop transmit
the RF signal and go back to sleep mode
when there is no tigger in 2 minutes.
Swipe the wheel magnet or crank magnet
about 1mm~3mm from the speed sensor
in order to wake up the combo sensor.
Do not drop a bike combo sensor or subject
it to severe shock.
Do not attempt to disassemble, repair, or
make any modification to a bike combo
sensor. Any attempt to do so will make the
warranty invalid.
Do not expose a bike combo sensor to
extreme temperature and excessive
moisture. Use diluted neutral detergent on
a soft cloth to clean a bike combo sensor.
Cadence Sensor
Nylon Ties
Nylon Ties
Nylon Ties
Wheel Magnet
Wheel Magnet
Wheel
Magnet
Crank Magnet
Crank
Magnet
Speed Sensor
Battery Cover
Rubber Band
Rubber Band
Rubber Band
Chain Stay
Chain Stay
Chain Stay
1
4
3
2
<3mm
<3mm
Biky Coach
MapMyFitness
Runtastic
Road Bike
Wahoo Utility Wahoo Fitness
MapMyRIDE
Myway Fit
App Store
Available on the
For iPhone 4S/5 or above
For Android
(GIQ
9KZZOTM
(OQK3KZKX
1
2
3
3
4
The range for rotating is 180
BT003
BLUETOOTH 4.0 BIKE COMBO SENSOR
Specification
Warning
Connecting Guide
Activate the Bluetooth function in
the setting of your smartphone.
3.Select and activate the bluetooth
interface to connect the Bike Meter
to the smartphone.
choose the
Bike Meter.
Detected,not
paired Disconnect
paired
Connected
the color turn
more dark.
when the Heart Rate
Monitor connected,
this small icon shows
up as well.
grey color,before
connected.
select “Bike
Meter”.
the two small
icons will show
up when con-
nected.
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Caution!
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.