CPE5450/CPE5450 Master/CPE5450 Slave /CPE5450CD/CPE5450AP/CPE5450FIT/CPE80R/CPE5300/1200AP User Manual Ver1.
Specifications : 1.Preparation for installation: 1-0 Shake the devices (CPE5450) separately, to check if the device is damaged from shipment, if you can hear some noise from inside of the device, and you suspect it maybe PCBA board loosened, please contact us, we will help check if you need a replacement.
1‐1‐3 1‐2 Ensure you know the CPE kit are ready for installation This step is to verify wireless connection between 2 CPE5450, to make sure they can talk each other, It also helps user to be familiar with the product and prevent any defective item caused by delivery etc. Please be kindly noted that you will need to prepare either a router or a computer for this step. Using both a router and a computer to check is preferred.
Equipment: CPE5450 Wi‐Fi router /cabled router PC (Notebook) Ethernet Cable POE Power Adapter 1 pair (2PCS) 1pcs 1 set 4pcs 2pcs (Ethernet Cable Length:<60M, or 194ft) 1‐2‐1‐1 Use Ethernet cable to connect POE port of power adapter to LAN port of CPE5450 (1#) 1‐2‐1‐2 Use Ethernet cable to connect WAN port of CPE5450(1#) to LAN port of Wi‐Fi Router 4
1‐2‐1‐3 Use Ethernet cable to connect POE port of power adapter to WAN port of CPE5450 (2#) 1‐2‐1‐4 Use Ethernet cable to connect LAN port of CPE5450(2#) to PC 1‐2‐1‐5 Set range between CPE5450 1# and CPE5450 2# : 3 meters is recommended, without obstacle between 2 CPEs 1‐2‐1‐6 Turn on all equipment, especially check as below to see if 2 CPE5450 are turning on, wait for 1 minute 5
Light is on Light is not on 1‐2‐1‐7 Light information Normal lights are as followings: 1‐2‐1‐8 Ping IP address of the Wi‐Fi router (some is:192.168.1.1 or 192.168.0.
Following is 192.168.1.1 , Win7 OS A. Click “Windows” icon B. Input command “ping 192.168.1.1 –t” C. Click “enter” to Ping 192.168.1.
Following messages indicates the CPE5450 devices are working well. And you don’t need to execute step 1‐2‐2. You could proceed to execute step 2‐1 instead. 1‐2‐2 Using a computer to check. If devices you have are in same mode, like both devices are in S mode (Slave) or in M mode (Master), you could neglect this step and proceed to step 2‐1.
1‐2‐2‐2 Connect CPE5450 2# to power adapter as following: 1‐2‐2‐3 Set range between CPE5450 1# and CPE5450 2# : 3 meters(around 10 foot) is recommended, without obstacle between 2 CPEs : 9
1‐2‐2‐4 Turn on all equipment, especially check as below to see if 2 CPE5450 are turning on, wait for 1 minute Light is on Light is not on 1‐2‐2‐5 Light information Normal lights are as followings: 10
1‐2‐2‐6 Set IPv4 IP address or IPv6 IP address of the PC to “192.168.188.22”(or 192.168.188.11 etc.), A. B‐ C. Left click “Change Network Adapter Setting” D.Set IPv4 IP address or IPv6 IP address of the PC to “192.168.188.22”(or 192.168.188.11 etc.
1‐2‐2‐7 Ping “192.168.188.252 ‐t” Following is Win7 OS A. Click “Windows” icon B. Input command “ping 192.168.188.252 ‐t” C. Click “enter” to Ping 192.168.188.
Following messages indicates one CPE5450 device(Master) is working well. 1‐2‐2‐8 Ping “192.168.188.253 ‐t” A. Click “Windows” icon B. Input command “ping 192.168.188.253 ‐t” C. Click “enter” to Ping 192.168.188.
The CPE devices are working ok. 2.
2‐1‐2 Use Ethernet cable to connect LAN port of CPE5450 1# to POE port of power adapter 2‐1‐3 Use Ethernet cable to connect LAN port of CPE5450 2# to POE port of power adapter 15
2‐1‐4 Use Ethernet cable to connect WAN port of CPE5450 2# to NVR/DVR 2‐1‐5 Turn on all equipment, especially check as below to see if 2 CPE5450 are turning on, wait for 1 minute, then you could see video of camera on monitor Light is on Light is not on 2‐2 With more than 2 cameras Sketch diagram 16
2‐2‐1 Use Ethernet cable to connect switch to IP cameras 2‐2‐2 Use Ethernet cable to connect switch to CPE5450 1# 2‐2‐3 Use Ethernet cable to connect LAN port of CPE5450 2# to POE port of power adapter 2‐2‐4 Use Ethernet cable to connect WAN port of CPE5450 2# to NVR/DVR 2‐2‐5 Turn on all equipment, wait for 1 minute, then you could see video of camera on monitor 2‐3 With your router, to extend Wi‐Fi signal, CPE5450 kit are used as Wi‐Fi repeater 2‐3‐1 Please kindly refer to step 1‐2‐1 (from 1‐2‐1‐1 to 1‐2
Warning: Do not push “Reset” button of CPE4540, if you keep pushing “Reset” button for longer than 15 seconds, the devices will not maintain connection between 2 CPEs, and then they need to be re‐configured. If you push “Reset”button one time (not longer than 5 seconds), it may cause 3 minutes to 5 minutes transmission issue (not stable) , but it will resume by itself. 3.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
