HIGH POWER WIRELESS LINK KIT FOR INTELLICENTER™, INTELLITOUCH® AND EASYTOUCH® CONTROL SYSTEMS INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
Technical Support Phone: (800) 831-7133 - www.pentair.com Contents FCC Regulatory Safety Notice............................................................................ 3 High Power Wireless Link Kit Overview.............................................................. 4 High Power Wireless Link Kit Contents............................................................... 4 High Power Wireless Link Indoor Transceiver LEDs and Connectors.................
FCC Regulatory Safety Notice 3 FCC non-modification statement: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
High Power Wireless Link Kit Overview The High Power Wireless Link consists of an indoor and outdoor 902-928 MHz wireless transceiver. Note: The wireless transceivers ship from the factory as a matched pair. The ID numbers on each transceiver must be the same number to function correctly. If needed, the transceivers must be replaced as a matched pair. For more information, call Customer Support 800.831.7133.
High Power Wireless Link Indoor Transceiver LEDs and Connectors 1.75 in HIGH POWER WIRELESS LINK Keep this side clear of ALL metal objects for 2 ft. (61 cm) Model: HVIN: FCC ID: ISED: 2.16 in HPW-WETHLINK HPW-WETHLINK 2AHWAQTSHPWETH 21176-QTSHPWETH High Power Wireless Indoor Transceiver LEDs PWR: Green LED on: Power is on to the unit. RX: Yellow LED indicates the unit is receiving data. TX: Green LED indicates the unit is transmitting data.
High Power Wireless Link For ScreenLogic Interface Systems Connect the High Power Wireless (HPW) Indoor Transceiver to the ScreenLogic® Interface Protocol Adapter as follow: See Figure 6 on page 12. 1. Using the provided 1 ft. RS-485 cable, connect one end of the cable plug to the Protocol adapter and the other end to the HPW Link indoor transceiver. The cable plugs are keyed for easy connection. See diagram below. 2. Plug the 120 VAC Power Adapter into an AC grounded electrical outlet.
Wall Mount the HPW Indoor Transceiver (Continued) Secure communication cable in slot in base Secure AC power cable in slot in base Protocol adapter SCREENLOGIC® INTERFACE 120 VAC power adapter Figure 1: Cradle/Desk Mount the HPW Indoor Transceiver Mounting screw/plug (2x) Hang module on screw head (approx. 1/16 in from wall surface) 1 16 " (0.
Mounting and Connecting the Outdoor High Power Wireless (HPW) Transceiver to the Automation Control System Load Center The following describes how to mount and connect the HPW Link outdoor transceiver to an IntelliTouch® or EasyTouch® Automation Control System Load Center or Power Center. See Figure 6 on page 12. Mounting the HPW Outdoor Transceiver The HPW outdoor transceiver is a two-way radio device with an attached antenna that communicates with the automation control system via a 15 ft.
Connect the HPW Link Outdoor Transceiver Cable to the RS-485 COM Port on Automation Control System WARNING Switch OFF the main power to the Load Center before making any connections. 1. Switch OFF the AC power to the enclosure at the main house panel circuit breaker. 2. Connect the four conductor connection cable to the screw terminal on the HPW Outdoor Transceiver circuit board as shown below in Figure 4. HPW Outdoor Transceiver circuit board YEL BLK RED GRN RS-485 Continue to next page.
Connect the HPW Outdoor Transceiver Cable to the RS-485 COM Port on Automation Control System (Continued) WARNING Switch OFF the main power to the Load Center before making any connections. 3. Unlatch the front door latch and open the front door. Remove the two retaining screws from the High-Voltage Cover Panel and remove the panel. See Figure 5 below. 4. Loosen the two retaining screws securing from the top edge of the Outdoor Control Panel.
6. Strip the leads of the communication cable wires back ¼ in. Insert the wires into the connector screw terminals. Using a small flatblade screwdriver, secure the wires with the COM PORT (J7/J8) terminal screws. Note: Multiple wires may be inserted into a single screw terminal.
High Power Wireless Link Kit Installation Guide SCREENLOGIC® INTERFACE AC Power Adapter (Indoor wall outlet) 900 MHz Wireless Link to outdoor Transceiver DSL or Cable Modem RJ11 Wireless Router RS-485 RJ45 Ethernet (RJ45 - CAT 5) to Wireless Router LAN Port 1 2 3 4 WAN LAN PORTS Ethernet RJ45 RJ11 for DSL Coax for Cable ScreenLogic2 program Intternet Intellicenter.
INTELLICENTER® CONTROL SYSTEM (Replacing Existing Wireless Antenna with High Power Wireless Link WARNING Switch OFF the main power to the Load Center before making any connections. 1. Switch OFF the AC power to the enclosure at the main house panel circuit breaker. 2. Unlatch the front door latch and open the front door. Remove the two retaining screws from the High-Voltage Cover Panel and remove the panel. See Figure 5 on page 10. 3.
Ethernet Port HPW Outdoor Transceiver circuit board Case Back plate for mounting circuit board Transceiver case retaining screws (x2) To Ethernet Port on IntelliCenter Circuit Board HPW Link Outdoor Transceiver 2-Pin 24 VDC Socket (to Power Module) Power Cable High Power Wireless Link Outdoor Transceiver AUX 5 AUX 6 AUX 7 AUX 8 AUX 9 Power Module Ethernet (Cat5) Cable (from HPW transceiver Place the Power Module in the low voltage compartment From Ethernet Port (J14) Figure 7.
INTELLICENTER CONTROL SYSTEM (Without an Existing Transceiver) WARNING Switch OFF the main power to the Load Center before making any connections. 1. Switch OFF the AC power to the enclosure at the main house panel circuit breaker. 2. Unlatch the front door latch and open the front door. Remove the two retaining screws from the High-Voltage Cover Panel and remove the panel. See page 11 for connection diagram. 3.
1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000 10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000 WWW.PENTAIR.COM All Pentair trademarks and logos are owned by Pentair or by one of its global affiliates. ScreenLogic®, EasyTouch® and IntelliTouch® are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. and/or its affiliated companies in the United States and/ or other countries. iPhone® is a registered trademark of Apple Corporation.