M10 Quectel Cellular Engine M10 User Guide M10_User_Guide_V1.
Document Title M10 User Guide Version 1.00 Date 2009-07-07 Status Release Document Control ID M10_User_Guide_V1.00 General Notes Quectel offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Quectel. The information provided is based upon requirements specifically provided to Quectel by the customers.
1 .EVB kit introduction 1.1 EVB top and bottom view EVB top view EVB bottom view M10_User_Guide_V1.
A: B: C: D: E: F: G: H: I: J: K: L: M: N: O: P: Q: R: Debug port Main UART port Test points Adapter interface Module operating status indication LEDs PWRKEY button EMERG_OFF button VBAT switch VCHG switch (charge function) Download switch Connector for M10-TE-A board Screw holes for fixing the M10-TE-A Headset socket Handset socket of audio channel 2 Handset socket of audio channel 1 Antenna connector fixing hole Screw holes for EVB placement SIM card socket 1.
EVB and accessories 2. Operational description 2.1 Tune up procedure Firstly，please equip the module and accessories as the figure 4. M10_User_Guide_V1.
Then ,switching the H switch to ON state, J switch to ON state； Press the F button PWRKEY for about 2 second, then the LED glint，and the module is tuningup successfully；( the location of All Switches and buttons please see the Figure 1) 2.2 Serial interfaces The module provides two unbalanced asynchronous serial ports. One is the serial port ,the other is the debug port. The module is designed as a DCE (Data Communication Equipment), following the traditional DCE-DTE (Data Terminal Equipment) connection.
MODULE (DCE) CUSTOMER (DTE) Serial port Serial port1 TXD RXD RTS CTS DTR DCD TXD RXD RTS CTS DTR DCD /RING RI Serial port2 Debug port DBG_TX DBG_RX /TXD /RXD Connection of serial interfaces Note: The RTS PIN must be connected to the GND in the customer circuit when only the TXD and RXD are used in the Serial Port communication. 2.3 Antenna interface The Pin 43 is the RF antenna pad. The RF interface has an impedance of 50Ω. 2.3.
2.3.2 RF output power The module conducted RF output power Frequency GSM850 EGSM900 DCS1800 PCS1900 Max 33dBm ±2dB 33dBm ±2dB 30dBm ±2dB 30dBm ±2dB Min 5dBm±5dB 5dBm±5dB 0dBm±5dB 0dBm±5dB 2.3.3 RF receiving sensitivity The module conducted RF receiving sensitivity Frequency GSM850 EGSM900 DCS1800 PCS1900 Receive sensitivity < -107dBm < -107dBm < -107dBm < -107dBm 2.3.
T‐type matching circuit π‐type matching circuit NOTE: The impedance of traces in Bold type must be 50Ω. M10_User_Guide_V1.
3. M10 features 3.2.1 General specification M10 is a Quad-band GSM/GPRS module delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. M10 can be used for WLL applications/M2M application and much more. Quad- band GSM/GPRS module with a size of 29x29x3.6mm ● Customized MMI and keypad/LCD support ● An embedded Powerful TCP/IP protocol stack ● Supply voltage range 3.4 ... 4.
M10_User_Guide_V1.
3.2.3 Software Specification Feature Power supply Power saving Frequency bands GSM class Transmitting power GPRS connectivity Temperature range DATA GPRS: CSD: SMS FAX SIM interface Antenna interface Audio features Serial port and Debug port Phonebook management M10_User_Guide_V1.00 Implementation Single supply voltage 3.4V – 4.5V Typical power consumption in SLEEP mode to 1.1 mA@ DRX=5 0.7 mA@ DRX=9 Quad-band: GSM850, EGSM 900, DCS1800, PCS1900.
SIM Application Toolkit Real time clock Alarm function Physical characteristics Firmware upgrade Support SAT class 3, GSM 11.14 Release 99 Implemented Programmable via AT command Size: 29±0.15 x 29±0.15 x 3.6±0.3mm Weight: 8g Firmware upgrade over serial port 3.2.4 Solution of M10 The hardware solution is MT6223D+AD6548+PF08155B+HWR874-2+SST34HF3284; The software solution is MTK Release 0836. 3.2.5 Radio frequency units The RF units for M10 include AD6548 (transceiver), PF08155(PA), HWX874-2(FEM).
2) PF08155 M10_User_Guide_V1.
3) HWX874 M10_User_Guide_V1.
3.2.6 Baseband units The baseband units for M10 include MT6223D and SST34HF. 1) MT6223D (MT6223D is integrated Digital baseband and analog baseband). Baseband architecture comprises mainly two chips: MT6223D and Combo Flash. MT6223D is an entry level chipset solution with class 12GPRS/GSM modem. It integrates not only analog baseband but also power management blocks into one chip and cangreatly reduce the component count and make smaller PCB size.
modules. Timing Generator - generates the control signals related to the TDMA frame timing. Power, Reset and Clock subsystem - manages the power, reset, and clock distribution inside MT6223D LDOs, Power-on sequences, swicthes and SIM level shifters. 2) SST34HF Features： 32-Mbit Flash and 8-Mbit PSRAM 2.7V~3.0V Operating voltage Flash：32-megabit（2M*16）2.7V to 3.
test point M10 BOTTOM VI EW M10_User_Guide_V1.
4．AT command （please see the AT command document） 5. Compliance with FCC Regulations Manufacturers of mobile or fixed devices incorporating this RF module are authorized to use the FCC Grant of this RF module for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains TX FCC ID XMR-16182009002”.
1.This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation. When the M10 is integrated into a final product, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel，door or cover is easily removed.
Shanghai Quectel Wireless Solutions Co., Ltd. Room 801, Building E, No.1618, Yishan Road, Shanghai, China 201103 Tel: +86 21 5108 2965 Mail: info@quectel.
