GV300 User manual GV300CAN User Manual GPS Tracker TRACGV300CANUM001 Revision: R1.
GV300CAN User Manual Document Title GV300CAN User Manual Version R1.02 Date 2018-01-22 Status Release Document Control ID TRACGV300CANUM001 General Notes Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers.
GV300CAN User Manual Contents Contents ............................................................................................................................................ 3 Table Index ........................................................................................................................................ 4 Figure Index....................................................................................................................................... 5 0. Revision History .......
GV300CAN User Manual Table Index TABLE 1. GV300CAN PROTOCOL REFERENCE ................................................................................. 7 TABLE 2. TERMS AND ABBREVIATIONS ........................................................................................... 7 TABLE 3. PARTS LIST ........................................................................................................................ 9 TABLE 4. DESCRIPTION OF 16 PIN CONNECTIONS ....................................
GV300CAN User Manual Figure Index FIGURE 1. APPEARANCE OF GV300CAN ........................................................................................... 8 FIGURE 2. THE 16 PIN CONNECTOR ON THE GV300CAN .................................................................. 9 FIGURE 3. OPEN THE CASE ............................................................................................................. 11 FIGURE 4. CLOSE THE CASE ................................................................
GV300CAN User Manual 0. Revision History Revision Date Author Description of change 1.00 2017-09-12 Super Zhao Initial 1.01 2017-12-19 Super Zhao Adjust the pictures and some description 1.
GV300 User Manual 1. Introduction The GV300CAN is a compact GPS tracker designed for a wide variety of vehicle tracking applications. It has multiple digital/analog I/O interfaces that can be used for monitoring or controlling external devices. At the same time, it has integrated CAN and J1708 which decodes information from vehicles digital buses (CANbus and J1708).It also includes a 1-wire interface used for driver ID and temperature monitoring.
GV300CAN User Manual 2. Product Overview 2.1. Check Parts List Before starting, check whether all the following items have been included with your GV300CAN. If anything is missing, please contact your supplier. Figure 1.
GV300CAN User Manual 2.2. Parts List Table 3. Parts List Name Picture GV300CAN Locator 80*49*26 mm User Cable GPS Antenna (Optional) MiniUSB_DATA_CABLE_1.5M (Optional) 2.3. Interface Definition The GV300CAN has a 16 PIN interface connector which contains the connections for power, I/O, RS232, CAN, J1708, 1-wire, etc. The sequence and definition of the 16PIN connector are shown in the following figure: Figure 2.
GV300CAN User Manual Table 4.
GV300CAN User Manual 3. Get Started 3.1. Open the Case Figure 3. Open the Case Insert the triangular-pry-opener into the gap of the case as shown above, and push the opener up until the case is unsnapped. 3.2. Close the Case Place the cover on the bottom in the position as shown in the figure above. Slide the cover against the direction of the arrow until it snaps.
GV300CAN User Manual 3.3. Install a SIM Card Open the case and ensure the unit is not powered (unplug the 16Pin cable and switch the internal battery to the OFF position). Slide the holder right to open the SIM card holder. Insert the SIM card into the holder as shown below with the gold-colored contact area facing down. Take care to align the cut mark. Close the SIM card holder. Close the case. Figure 4. SIM Card Installation 3.4.
GV300CAN User Manual 3.5. SYNC Switch The switch was used to Synchronize the car model. You can push the switch to the left as the Arrow direction，and hold it approximately 3 seconds to Synchronize the car model。 Figure 6. SYNC Switch Note: If device is configured for any car, synchronization can be started in the following way: 1. Make sure the CAN function is enabled before you push the SYNC switch. 2. Connect the power for the device. The CAN LED lights red. 3.
GV300CAN User Manual 3.6. Install the External GPS Antenna (Optional) There is a SMA GPS antenna connector on GV300CAN. The GV300CAN will automatically detect and use an external antenna when connected. Figure 7. GPS Antenna of GV300CAN 3.6.1. GPS Antenna Specification Table 6. GPS Antenna Specification GPS antenna Specification Frequency 1575.42 MHz Bandwidth >5 MHz Beam width >120 deg Supply voltage 2.7V-3.
GV300CAN User Manual Figure 8. Typical Power Connection 3.8. Ignition Detection Table 7. Electrical Characteristics of Ignition Detection Logical status Electrical characteristics Active 5.0V to 32V Inactive 0V to 3V or open Figure 9.
GV300CAN User Manual IGN (Pin3) is used for ignition detection. It is strongly recommended to connect this pin to ignition key “RUN” position as shown above. An alternative to connecting to the ignition switch is to find a non-permanent power source that is only available when the vehicle is running, for example, the power source for the FM radio. IGN signal can be configured to start transmitting information to the backend server when ignition is on, and enter the power saving mode when ignition is off.
GV300CAN User Manual 3.10. Analog Inputs There are one analog input on GV300CAN, The analog input voltage range could be selectable, Including 0-12V and 0-30V, and the default range is from 0 to 30V. The following diagram shows the recommended connection. Figure 11. Typical Analog Input Connection 3.11. Digital Outputs There are two digital outputs on GV300CAN. All are of open drain type and the maximum drain current is 150 mA. Each output has the built-in over current PTC resettable fuse. Figure 12.
GV300CAN User Manual Figure 13. Typical Connection with Relay Figure 14. Typical Connection with LED Note: 1. OUT1 will latch the output state during reset. 2. Many modern relays come with a flyback diode pre-installed internal to the relay itself. If the relay has this diode, ensure the relay polarity is properly connected. If this diode is not internal, it should be added externally. A common diode such as a 1N4004 will work in most circumstances.
GV300CAN User Manual 3.12. Serial Port/UART Interface There are two lines dedicated to the Serial Port/UART interface (TXD and RXD). TXD/RXD is standard RS232 signal. Figure 15. Typical Connection with RS232 Port 3.13. 1-Wire device Connection It has 1-wire bus on GV300CAN, which supports temperature sensors and iButton. The bus includes 3 signals, namely, VDD-1W, DATA-1W and GND.
GV300CAN User Manual Figure 16. Typical Connection with 1-wire Device Figure 17.
GV300CAN User Manual Figure 18.
GV300CAN User Manual 3.14. Device Status LED Table 10. Definition of Device Status and LED LED Device status LED status GSM (Note 1) Device is searching GSM network. Fast flashing (Note 3) Device has registered to GSM network. Slow flashing (Note 4) SIM card needs pin code to unlock. ON GPS chip is powered off. OFF GPS sends no data or data format error occurs. Slow flashing GPS chip is searching GPS info. Fast flashing GPS chip has gotten GPS info. ON Start the synchronization procedure.
GV300CAN User Manual Figure 19. GV300CAN LED on the Case Note: 1. GSM LED cannot be configured. 2. GPS LED and PWR LED can be configured to turn off after a period of time by using the configuration tool. 3. Fast flashing: for GSM LED is about 60 ms ON/780 ms OFF; for GPS LED and PWR LED is about 100 ms ON/100 ms OFF. 4. Slow flashing: for GSM LED is about 60 ms ON/1940 ms OFF; for GPS LED and PWR LED is about 600 ms ON/600 ms OFF. 5. When only CAN-bus is connected. 6.
GV300CAN User Manual 3.15.1. Bluetooth usage Install Lightblue APP on your smartphone for IOS, and install NRF Connect for Android. Send command: “AT+GTBTS=gv300can,1,,GV300CAN_BT,7,3,666,1D07,0003,0,123456,,,,,,,,,,,,FFFF$” by Manage Tool to device to turn on Bluetooth. The device will connect to smartphone. Send command “AT+GTBTS=gv300can,0,,GV300CAN_BT,7,3,666,1D07,0003,0,123456,,,,,,,,,,,,FFFF$” by Manage Tool to device to turn off Bluetooth. The device will disconnect to smartphone.
