GD100 User manual GD100 User Manual GSM/GPRS/GPS Tracker TRACGD100UM001 Version:R1.
GD100 User Manual Document Title GD100 User Manual Version R1.02 Date 2016‐02‐22 Status Release Document Control ID TRACGD100UM001 General Notes Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers.
GD100 User Manual Contents Contents ............................................................................................................................................ 3 0 Revision History .............................................................................................................................. 6 1 Introduction ................................................................................................................................... 7 1.1. Reference.....................
GD100 User Manual Table Index TABLE 1. GD100 PROTOCOL REFERENCE ........................................................................................ 7 TABLE 2. GD100 LED DESCRIPTION TABLE ......................................................................................
GD100 User Manual Figure Index FIGURE 1. APPEARANCE OF GD100 ..................................................................................................
GD100 User Manual 0 Revision History Revision Date Author Description of change 1.00 2015‐12‐23 Docter Xu Initial Release 1.01 2016‐01‐07 Black Chen Modify PWR LED description 1.
GV55 User manual 1 Introduction GD100 is a powerful GPS tracker designed for fixed asset tracking applications. It works with three CR123A lithium‐batteries and will operate for 60days with reading date and reporting four(4) times per day. With built‐in temperature sensor, GD100 will detect the outside temperature and trigger warning messages when outside temperature is out of operating temperature ranges ‐20℃‐85℃. And also, GD100 supports light detection and can trigger even messages by light sensor.
GV55 User manual 2 Product Overview 2.1. Appearance 1313 Figure 1. Appearance of GD100 2.2. Button/Switch/USB Interface Description USB Port/Power Switch Description START/STOP Button TRACGD100UM001 Start: When START button is pressed after received real time command ‘ACT’, the device enters start countdown mode. Stop: When STOP button is pressed, the device will not monitor temperature anymore.
GD100 User manual USB Port Toggle Switch If the battery switch is on, it will work as a serial port for configuration. If battery switch is off, it will work as a mass storage. Note: If you want to change work mode of USB, you need to reboot the device. Turn on GD100 when switch to “ON”. Turn off GD100 when switch to “OFF”. 2.3. LED Description There are five LEDs on GD100, the description as follows. Table 2.
GD100 User manual normally, and temperature bands alarm monitoring start delay countdown starts. 3. GD100 is in activation state, and STOP Button has been pressed: PWR light will flash fast and TEMP & DATA GREEN will be long on. 4. GD100 enters STOP mode: PWR & GPS & CELL lights will be off, and TEMP & DATA GREEN lights will stay long on. If temperature bands alarm has been triggered, TEMP RED light stays flash slowly. Note: 1.
GD100 User manual 3 .Getting Started 3.1. Part list Name GD100 Locater Picture Remark The GSM/GPRS/GPS locator. 3.2. Turn on/Turn off Turn on: Shift the Toggle Switch to “ON”, GD100 will turn on. Turn off: Shift the Toggle Switch to “OFF”, GD100 will turn off.
GD100 User manual 4 Troubleshooting and Safety Info 4.1. Troubleshooting Trouble Possible reason Solution After GD100 is turned on, the CELL LED always flashes quickly. The SIM card is not inserted. Please insert the SIM card into GD100. The signal is too weak; GD100 can’t register to the network. Please move GD100 into places with good GSM coverage. The SIM card in GD100 doesn’t support GPRS. Try a GPRS supporting SIM card. APN is wrong. Some APNs cannot visit the Internet directly.
GD100 User manual explosion. Please do not use GD100 on the airplane or near medical equipment. To satisfy FCC RF Exposure requirements for this transmission devices, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.