User's Manual

10
#590
Receiver
Computer
Take out Nano USB
Preparing for Use
1. Before operation, please take out the Nano
receiver on the back, as shown in the figure.
2. Please first select PC / Mac keynote / Mac PPT
3. Then plug the receiver into the
computer’s USB slot, as shown in the figure.
(Please confirm whether the computer interface and software is complete before
operating, confirm that the functions supported by this device function properly).
4. Slide the switch to the ON position, the LED on the top of LR-22 flashing for 1~2
seconds
5. Press any key to confirm whether the transmitter and receiver’s one-on-one code
calibration is functioning properly. If not, please follow the Frequency Search.
Note: When you set it to a wrong step and use this product, malfunctions will occur.
For example: If you set it to use on PC and used it on a Mac computer, the function
keys will malfunction.
How to operate Mouse/ Power Point / Keynote
How to operate Multimedia
Frequency Search
Usage and Related Information
Should the receiver not respond to the transmitter (LR-22) after installing the driver,
please use the following procedure to reset the transmitter
1. Plug the USB receiver into the USB port, suggest to keep USB receiver and
transmitter within 30cm distance.
2. Simultaneously press function keys 2 & 6, the LED on the top of the transmitter
( LR22) starts flashing
3. Release function key 2 & 6
4. When LED stops flashing, the frequency reset is done
NO. 6
key
NO. 2
key
Code matching LED indicator
Computer
Receiver
30CM
LR-22R
LR-22R Navi
LR-22G
LR-22G Navi
Laser Wireless Presenter
Features
Wireless Keyboard ,Mouse, Media Player
Quick Time Remote Controller for PC and Mac
With integrated Green Laser Pointer
- Best mate for PC PPT/ Mac Keynote/Mac PPT
- Integrated Green laser pointer
- Multimedia remote control - Windows Media Player
- Quick Time
- Rechargeable lithium battery embedded, save you US$100 battery cost
and green environment design
- RF operation distance up to 30 meters ( open space)
- Page up / page down
- Wireless keyboard ( Play/Esc ) & (Screen blank)
- Sensor Wireless Mouse control
- USB 2.0 connection, plug & play
- No software down loads & driver installation required
- Dual color LED as function indicator
- Power- saved on/off switch
- Nano USB receiver
Functions View
No Icon
Function No Icon Function
1
Mouse left key 16 Optical mouse
2
Mouse right key 17 Power switch
3
Laser 18
Mouse / PPT
4
Page up 19 WINDOWS / MEDIA
PLAY
5
Page down 20 QUICK TIME PLAY
6
Screen Blank 21 PC
7
Esc/ F5 22 Mac Keynote
8
Optical mouse 23 Mac PPT
9
Screen Size 24 USB charger
10
Mute / restore 25 LED
OFF
ON
Charging status display
11
Laser 26 LED(Green) laser ON
12
Volume up 27
LED(red)
Power on / code
calibration / low
power display
13
Volume down 28 Nano receiver
14
Fast forward
15
Rewind
Specifications
RF transmission / Range : 2.4G / 30 meter ( in open space)
USB interface : USB 2.0
OS supported : Windows 7,XP, 2000,98 OS Mac 9.0 or later
Wavelength : Green:532nm
Red:630~680nm
Power : Lithium battery x 1pc
Battery burn time : 5 hours
Output power : CLIIIa < 5mW , CLII < 1mW
Dimensions : 11.5(L) x 4.28 (W) x 2.75(H)cm
Weight : 62g
Warning: Laser radiation is harmful to the eyes. Do not stare directly into the beam.
Note: Please follow the user manual to operate / adjust this device, otherwise it is
possible to be exposed to harmful radiation.
How to re-charge the battery
Computer
Dual-color display LED
displays charging
USB
LR22 lithium battery can be charged over 500 times.
Please follow the steps to re-charge the battery
1. Plug the included USB cable one end into the USB drive and the other end
into the LR22 product’s USB slot (when the LED on the side shows red,
this means that it is charging).
2. When the battery is fully charged, the LED on the side will show green;
remove the USB cable to finish charging.
3. When battery power low, the LED in the front flashes for about 3~6 seconds,
this is to remind you insufficient power in the lithium battery, please charge
it as soon as possible.
532
According to FCC section 15.19, the following
statement must be shown on the label or user
manual.
“This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.”
And according to FCC Section 15.105
Information to the user, the following
information is required to be shown on user
manual for Class B digital device peripheral:
(b) For a Class B digital device or peripheral,
the instructions furnished the user shall
include the
following or similar statement, placed in a
prominent location in the text of the manual:
NOTE: This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the
instructions, may cause harmful interference
to radio communications. However,
there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception,