2. In frequency mode, press (GI) + number key EID and the screen will display Press (ED enter, and the screen will display . Press @or &D to select R-CT function. Press (CD enter. Press select O im off CSS, while select one CSS value from 67Hz to 254.1Hz. Press (ZI to confirm and press Gl return to standby. [edi This transceiver is with 50 groups CSS. Please see appendix(1) CSS frequency sheet.
Setting side key —-MENU 10 This menu is for the setting of the below two functions: 1. PF1 There are 5 options: Raddled Radii function SCAN: Scan function LAMP: Lamp function BAT-V: Battery pack voltage prompt OFF: Tum off the key function 2.PF2 There are 3 options: ALARM Start distant urgency alarm function SOS» SOS function OFF Tum off the key function 1.1 Program PF1 as FM radio function: + Turn on FM Radio: In standby mode, press PF1 to turn on.
11.2 Program PF1 to scan function: In standby, press PF1 to enter scan mode. (Scan mode is settled on the scan mode setting via Menuhin. Press any key to stop scan. 1.3 Program PF1 to lamp function: In standby, press PF1 to turn on lamp function. And press PF1 again to turn off lamp. 1.4 Program PF1 to BAT-V function: In standby press PF1 to start up the battery pack voltage prompt function. The screen will display the current battery pack voltage. [TN » Press GI key to exit the function.
Setting keypad auto lock (AUTO) — MENU 11 There are two options: manual lock and auto lock. We can set most of the keys unworkable in order to prevent from pressing a key wrongly. ON: "ON" means setting keypad auto lock function. After setting this function, the keypad will be automatically locked if there is no any operation in 15 seconds. Hold on for more than 2 seconds to unlock the keypad. » Manual lock: In standby, hold on E22 for more than 2 seconds to lock keyboard; and press £2 to unlock the keypad.
Setting frequency offset (RUNOFF) — MENU 13 There are 2 options: 1. AFT-D: Shift frequency direction 2. OFFSET: Offset frequency 1.SFT-D means as followings: a. The transmitting frequency is higher than receiving frequency. The shift frequency direction is positive. b.The transmitting frequency is lower than receiving frequency. The shift frequency direction is negative. ic. Turn off the shift frequency direction function.
For example, the receiving frequency of a repeater is 460.025MHz. The receiving CSS is 69.3Hz. The transmitting frequency is 450.025MHz. A. Setting receiving frequency in frequency mode, input sequence. 2. Setting shift frequency direction: in frequency mode, enter MENU refer P28) and select direction. 3.
Setting stopwatch function (SECOND) ~~ MENU 16 In standby mode, press (ED and number keys 2 G3 , the screen will display Press (ED enter, and then press select ON or OFF. Press (EJ to confirm, then press to rectum to standby. How to use stopwatch: When the stopwatch function is turned on, press once to count time. Press any key to stop counting time. Press 2 to resume. NOTE A » When the stopwatch stops counting time, press any key (except I ) to exit stopwatch function.
2 Please make sure you have memorized at least one channel and one channel name before changing channel mode and channel name mode. 2 Shortcut change over frequency mode and channel mode: In standby press you never set password, the work mode can be changed over directly. If you have set password, you need to input the password firstly, and then the work mode can be changed. Channel name edit (CH NAME) — MENU 18 Channel name edit: 1. Channel name can be made up of 26 or 10 Arabic freely. 2.
Setting memory channels (MEN-CH) — MENU 19 ‘When the transceiver works in frequency mode or in standby mode, you can input the frequency and ‘the parameter that you want to memorize into the channels. Press (ED + number keys (E2 EID, and the screen will display Press (ED enter, press select channel number. And then press CD) to memorize. There will be voice prompt when the memorizing is successful. Press to exit. This channel is co-frequency channel.
ANI ID code edit 21 In frequency mode, press (ED and number keys €XD I, the screen will display] Press (ZI enter, input your desired ANI ID Code directly. And then press (ZI to confirm, press to return to standby. 2 ANI ID code can be edited by 3-6 digits freely. ANI iD code is ranged from Setting MDT 22 There are five options: PT-ID: Setting ANI ID CODE transmit delay OPTICS: Setting MDT signaling SP MUTE: Setting mute mode ART: Setting ring time STAMFORD: Setting MDT side tone 43 1.
QT: When the transceiver receives the signal that is strong enough to open squelch and is matched with CTCSS/DCS, the speaker will be opened. If the transceiver is not set CTCSS/DCS, the speaker will be opened when the transceiver receives the signal that is strong enough to open squelch. QT + DT: When the transceiver receives the signal that is suitable for QT conditions and is matched with MDT signaling, the speaker will be opened.
All calls, group calls and selective calls There are ANI ID code transmission, ANI ID code edit and MDT decoding functions. Without the assistance of the other communication equipment, the all calls, group calls and selective calls are available between the groups. Before using all calls, group calls and selective calls function, you need to set as followings: 1. ANI ID CODE edit Note: Every transceiver in the same group should be edited a unique ANI ID code.
How to operate a. How to use all calls function: Hold on PTT key to transmit. After transmitting ANI ID Code, input CI) + (I keys directly. b. How to use group calls function: Hold on PTT key to transmit. After transmitting ANI ID Code, input "Group NO." How to use selective calls function: Hold on PTT key to transmit. After transmitting ANI ID Code, input the ANI ID Code of the selective transceiver that you want to speak to.