Gilda standby, press the screen display: Press (CI to enter, it shows ‘ON’, press select turn ON/OFF the power saver function. Press (50 to confirm, and then press GI to return to standby. Selecting transmitting power (TXP) — MENU 4 In frequency mode, press (CD + , the screen displays || § Press to enter, it shows ‘HIGH’, press /&2 to select HIGH/LOW power, then press (5) to confirm, finally press Gj to return to standby.
Gilda le le es Setting VOX (VOX) MENU 7 This transceiver will switch to the transmitting mode when detecting the voice signal. The transmitting operation wil somewhat be delayed, and the voice signal information may be not transmitted at the first beginning, since there needs some time for the VOX circuit to detect the voice signal.
Gilda le le es Beep prompt function (BEEP) -~ MENU 11 Beep prompt function is for the transceiver operating confirmation, error status prompt or faulty condition reminders; We faithfully advise you to keep this function ON, so that you can detect or check the errors and faults in time. In standby, press the screen display Press (ZI) to enter, it shows ‘ON’, press select tum ON/OFF the beep prompting function, then press (ZI to confirm, press finally to return to standby.
Gilda standby, press (C0 + Gab . the screen displays Press to enter, it shows ‘OFF’, press select ON/OFF this function, then press to confirm, finally press to return to standby. Setting receiving CSS (R-CTCSS) — MENU 15 Using the CTCSS/DCS can be used for you to receive the specified individual or group calls, and avoid the needless callings from others with the same frequency. Only receiving the same CTCSS/DCS signals, the transceiver can release the squelch.
Gilda le le es Setting transmitting DCS (AFDC) — MENU 18 In standby mode, press (C0 + CI) CID. the screen displays Press to enter, it shows ‘OFF’, press tum OFF this function or select DONN to D754] DCS code, then press (0) to confirm, finally press @q) to rectum to standby. > This transceiver has 105 groups DCS, see appendix (2) DCS frequency sheet. In DCS selections, DXXXN {from DONN to D754N) means POSITIVE code, while XXXI (from D023I to D7541} means NEGATIVE code.
Gilda SOS-CH (SOS function): In emergency, the transceiver transmits the SOS signals to the outside surrounding on the specified Channel or Frequency in Band A or Band B. Meanwhile, the transceiver will sound with the green light keeping flashing. It will transmit signals every 5 minutes, lasting for 10 seconds each time. ‘When the carrier signal receives in the SOS transmitting mode, the transceiver will automatically switch into the receiving mode.
Tiled ae lel et * Exiting from the radio mode: Press Side key 1 again to exit from the radio mode. 2 When the FM radio is working, the current frequency or channel is in standby. Once detecting the receiving signals, the transceiver will automatically switch to receiving/transmitting mode. Five seconds after the signal disappears, the transceiver will switch back to the radio made. 3 In FM radio made, press Ei to back to the current standby frequency, and press PTT to transmit.
Gilda le le @ With password Input Please set the password for the mode switch via KG-UVD1P programming software. This password is consist of 6 charters from 0 to 9. The valid password should be made up by six digits except In standby, press + CFP C2). then press choose one of FREQ/NAME/CH/CHFREQ. Press to confirm, then the screen will display the password input . Please input the preset password through the keypad, then the transceiver will switch to the selected mode.
Deleting channel (DEL-CH) MENU 28 In standby mode, press (G0 + CX) (I5) , the screen displays Press (0 to enter, and press select the desired channel, then press (= to confirm, After the channel is deleted successfully, press Gj to return to standby. Setting reset —— MENU 29 This transceiver has two selections for the reset operation-VF reset and ALL reset. VFO reset means all the functional parameter set in frequency mode resumes to the factory setting.