Setting Offset Frequency (OFFSET) — MENU 23 Offset frequency means the difference between Tx and Rx frequency. This transceiver's offset frequency age is between 0 to 63.950MHz. In standby mode, press (+ CFP €X) , the screen displays Press (C0) to enter, then press select offset frequency or input the offset frequency through key pad directly press (EJ) to confirm, press Gli return to standby.
Setting Stopwatch Timer (SECOND) — MENU 25 In standby mode, press the screen displays |* Press (ZI) to enter, it shows ‘OFF, then press turn ON/OFF this function, press Cte confirm, press return to standby. Using the stopwatch timer: When this function is ON, press GF) to start counting, while press any key to stop. Press GF) again to start counting. OTE /\ 2 Stop counting, press any key (except (I) key) to exit stopwatch timer function. channel name Edit (CH NAME) -— MENU 26 Edit Channel name: 1.
Setting Memory Channels : Setting Co-channel and Dis-channel (MEN-CH) -— MENU 27 In Frequency mode and in standby, you can input the desired storing frequencies and each parameter. press the screen displays Press (CI) to enter, press select channel, then press (Eto store, a voice prompt means receiving stored. Press GI) to exit, the current channel is co-channel. If you need to store dis-channel, repeat the above operation, another voice prompt means sounds — transmitting stored. E.g-: setting 450.
Setting Reset — MENU 29 This transceiver has two resets available VFO and ALL messages. ‘When you use RESET VFO, all function parameters will return to default set. ‘When you use RESET ALL, the transceiver’ all settings rectum to default set. 1. MENU Reset (VF: In standby mode, press the screen displays Press (Sto enter, and press select VFO, then press (ED the screen display: press (=D again to confirm, and the screen displays 5). After set Reset, the transceiver will auto power off and reboot again. 2.
Setting Priority Scan Function If you want to monitor the other frequency and check the certain preferred frequency at the same teems, you can set Priority scan function. E.g.: Scan six channels: CH1, CH2, CH3, CH4 and CH5 as the common scanned channel, and CH6 set as the priority scanned channel. Scanning sequence as following chart: CH1_ CH6_ CH2_ CH6 _ CH3 _ CH6 _ CH4 _ CH6_ CH5_ CHé L ] If the transceiver checks the signal on "Priority Channel", it will call out its frequency.
Wire clone function Switch resourceful on, after you have LED is flashing red during cloning. connected the target radio to the radiosurgery LED goes out In case of successful cloning. via the cloning cable, push the [MINI] key | LED glows continuous red In case of cloning Using redirection and the source radio starts cloning. failure. LED Is flashing gran during cloning. Target radio LED wil switch OFF when cloning complete.
How to troubleshooter shoo How to use the intelligent charger 1. Insert the AC plug into the outlet (AC: 90-240V), the charger indicator flashes, it means enter charging standby . 2. Insert the battery into the charger, the RED indicator turns on, it means charging, while GREEN indicator tums on, it means fully charged.
ei ( Problem Solution be stored Some functions can not Make sure work in Channel mode. Some functions can be set only via programming software in Channel mode. Receive other groups sign \al while communicating Pls change another CTCSS/DCS code of your group. a4 Technology parameter Came Appendix 1 ~ (cress 1 67.0 1 94.8 2 131.8 3 171.3 4 2035 2 69.3 12 97.4 22 136.5 32 1738 42 206.5 3 71.8 13 100.0 23 141.3 33 177.3 43 210.7 4 74.4 14 103.5 24 146.2 34 179.9 44 218.1 5 77.0 15 107.2 25 151.4 35 183.
( 76-108MHz (Rx) ) Frequency range UHF: (TX) VHF: (Tx/Rx} Memory channels 128 channels Operating Voltage 7.4 Operating Temperature -30C to + 60C Working Mode Co-channel or Dis-channel simplex Output Power VHF: 5W / UHF Modulation F3E(FM) Max. Frequency Deviation < kHz Spurious Radiation < -60dB Frequency Stability +2.5 ppm Receive Sensitivity <0.2uv Audio Output power > 500mwW Dimension 58 X 105 X 39 (mm) \ Weight 250g J edi 3 2 Specifications are subject to change without notice.
@rowan endeavors to achieve the accuracy and completeness of this manual, but is not liable for any possible omission and printing errors. All the above specifications are subject to change by @won without prior notice.