CD rig beer pit CD CD+CD + [7=75, > CD + fri? [Terr > CD far! Cha P20 P21 Chris => Chap Arctics Scan mode(T = CI) EAN.
9 Reset (=e CE-» Speed Search @¥ / K&D (See page 07) m SOS-CH (SOS function) (See page 25) P38 m Priority scan function (See page 38) m Set Reverse Frequency (20) (See page 38) m Low-battery voice prompt (See page 39) m Transmit overtime prompt (See page 39} m Adding scanning channel function (See page 39) ® Wire clone function (See page 40) m Working with repeater (See page 40-41) 12 How to operate cm] Menu Locked function To avoid operating menu often, you can set Menu Locked function on through the prog
Setting Frequency Step (STEP) —— MENU 1 In standby, press the screen displays Press (ZI) to enter, it shows “12.50K’, press select the desired step, then press (I) to confirm, press Eg) return to standby. This transceiver has seven frequency steps available: 5.00KHz, 10.00KHz, 12.50KHz, 25.00KHz, 50.00KH; and 100KHz. Setting Squelch Level (SQL-LE) — MENU 2 This function means turn on the squelch when the signal is strong while tum off the squelch when the signal is weak.
Setting Begin/End Transmitting Voice Prompt (ROGER) — MENU 5 This function means to select transmitting voice prompt way: OFF: turn off this function, without any voice prompting. BOT: press PTT, voice prompt when begin transmitting EOT: release PTT, voice prompt when end transmitting BOTH: press and release PTT, voice prompt in standby, press CI + , the screen displays Press (ZW to enter, it shows ‘OFF’, press select OFF/BOT/EQT/BOTH, then press (ZI) to confirm, press GI) return to standby.
Setting Voice Prompt (VOICE) — MENU 9 In standby, press the screen displays [ride SINGLETS Setting Transmit Overtime Alarm (TOA) -— MENU 10 Tum on TOA function, when your transmission reached the preset TOT (transmit over time), the transceiver will alarm and TX indicator flash. This transceiver can be set from 1 to 10 TOA level with 1 second each. 1 level means the transceiver prompt 1 second before transmitting reached to TOT.
Busy Channel Locked (BCL) — MENU 13 This function is to prevent the interference of other communicating channels. if the selected channel was occupied, press [PT, the transceiver can not transmit. In frequency mode, press the screen displays Press (0 to enter, it shows ‘OFF’, press select ON/OFF this function, then press (IO to confirm, press EI) rectum to standby. Setting Keypad Locked (AUTO) -— MENU 14 This transceiver has Auto-lock and Manual-lock available.
How to operate Setting Transmitting CSS (FCTCSS) — MENU 16 In standby, press the screen displays Press (ZI) to enter, it shows 'OFF', press @9 to turn OFF this function or select 67.0Hz to 254.1H; CSS code, then press (ZI) to confirm, press return to standby. NOTE 2 This transceiver has 50 groups CSS, see appendix (1) CSS frequency sheet.
Setting Scan / Lamp / SOS-CH / Radio Function on Side key 1 (PF1) — MENU 20 There are four functions available on the side key 1 of this transceiver: SCAN: Scan function LAMP: Lamp function SOS-CH: SOS function RADIO: FM radio function OFF: Tum off functions 1. Scan function: In standby mode, press Side key 1 enter to Scan made (scan mode can be set through MENU 19 -Scan Mode Setting), press any key to stop scanning.
4. RADIO function: #Tums on the Radio: in standby mode, press Side key 1 to turn on. The screen displays '* 3: will search the radio stations automatically when the green light flashing, and will stop until searched, You can listen the radio. «Tune the radio stations: In Radii mode, press (29 , the radio will tune the stations automatically and the green light flashing at the same time, it will stop tuning while searched the station. You can also press turn the radio stations.
Working mode (CH-MD F) -~ MENU 21 This transceiver has two working modes available: 1. Frequency mode (FREQ) 2. Channel mode Three kinds of channel mode available: @Channel (CH) @Frequency + Channel number (CH FREQ) @Channel name (NAME) » Only input the shift password can change Frequency mode into Channel mode, while change among the three kinds of channel mode without inputting password. >To set the shift password via KG-UVD1 programming software.