The transceiver will velum to its normal operation when the power is switched ON or papal shove operation, 138r Important: The mange of displayed valiant is only from 7V Tokyo DU, because the displayed value Is estimated, please use a voltmeter when a more precise reading ls desired Antenna Connection Before operating, install an efficient, well-tuned antenna. The success of your installation will depend largely on the types of antenna and #8 correct installation.
SP-a = Microphone For voice communications, connect a microphones equipped with an 8-pin modular pug into the modular socket on the front of the main unit. Press firmly on the plug until the nicking tab clicks. Attach the supplied microphone hanger in an appropriate location using ihe screws included in the screw set.
Getting Acquainted key unt loon appears then press the following key. # Front panel F Confirms the selective functions and exit P1 TX power set P2 Voice commander P3 Sorta memory channel P4 Delete memory channel Basic Functions Ps Keypad lock I= KEY key and following key together to activate following function: 1 Pow(Power) Power on/Off 0 2 VoL Adjust Volume Key P1 Data clone 2 be Dial SUSE fn memory channel and scan direction etc.
Rear panel le} KEY FUNCTION 1 Ext. Power Jack Terminal for connecting optional cable for use with ignition key OnJ/Off function. The radio will auto power on when cer is driving The radio will auto power off when car stops. 2 Ext.Speaker Terminal Terminal for optional external speaker SP-01 3 Antenna Connector Connection for 50Q antenna. # DISPLAY NO. KEY FUNCTION 1 saL Squelch level 2 M In channel mode. 3 32 Indicates the channel number in channel mode.
E Microphone up Increase frequency channel number or setting value. DOWN Decrease frequency, channel number or setting value. PTT Press the PTT (Push-TO-Ta} key to transmit Number Key Input VFO frequency or MDT dial out etc. MDT ON/ OFF Switches between MDT dialing or function operating. LOCK Switch Locks out the UP Down Numerical keys and Function keys. ENE MIC Speak here during transmission.
£VPG Mode{Frequency mods}: This mode shows only frequency on the display. Short operation and Channel setting will be changed & snored as the is test value permanently. Incs the radio is tumid off or changed new VFO frequency, the latest settling is remained until next (Pie 3) pic 3} 3. Professional Transceiver Mods: When sel display mode as Tommy CHP it enters into Professional Transceiver mode. At this mode, except scan other shootout operation can't operate And from No.
of frequency in serene will bs auto hidden. In this stalls, tum selector knob or Microphone [TED EE) | key will increase or decrease frequency quickly by MHz step . 2. Under channel mods, you can sangs the current channel to the desired one through selector knob, clockwise tum to the forward channel, anticlockwise tum to the backward channel. In relative working mode, Microphone's [TE /C7L0) 1 ksy has same Unction for adjusting frequency and channel NOTE: 5k, 625k, 12.
Channel Delete A. Under channel mode, tum selector knob to select channel which you want to delete. 2 Press kay and (00) key together, current chains! wil be deleted and emitted and emitted a prompt voids. Bl icon flashing means current channel! is delta Shortcut Operations Squelch Off lay programmed as Squelch OF fo monitor the weal signal. 4. Squelch OFF: Press «oy to disable squelch press fey again to resume squelch.
knob or press Microphone's | (TG) /TLL) 11e select desired DCE encode and decodes; 4. Total groups; total 1024 groups. N is positive code is inverse code. 5. Press any key except and (E52 keys to rectum into standby status. NOTE: Under channel mode, this operation can be temporarily used by user.
5. Tum selector knob or Mics | TIER 7 E20) folksy to changes offset frequency, offset frequency changed as per stepping. 8. Press any kay except key to exit into standby. NOTE: Under channel mode this operation can be temporarily suds by user.