Setting transmitting VOX ON or OFF and VOX sensitivity lave! 1. Press [MENU and then rotate ihe channel knob [ENCY to menu no. [O71 , the LCD will display: Menu Number (Flickering) 2/7 Selection Indicator ale a WE creed Setting lem OFF=be Tolerant valve 2. Crass [MENU again, LCD display: a? WO tn OFF 3. Rotate the chance! knob [ENC] to select your desired VOX ON or OFF, meanwhile, to set the set VOX sensitivity level, 4.
Setting keypad beep ON or OFF 1. Press YEMEN and then rotate the channel knob [ENC] to menu no. £113 LCD will display: Menu Umber (Flickering) Selection indicator a i BEEF ~~ Setting fem (abi Current value 2. Press [MENU again, LCD display: 11 BEEP te OM 3. Rotate the channel knob [ENC] to select the keypad beep ON or OFF. 4. Press [MENU]J to confirm and store the current setting value and continue other setting, or press [EXIT] to cancel the selling and exit the menu mods at the same ims.
Betting receiving CSS (ROTC) 1. Press [MENU and then rotate the chant knob [ENG Y to menu no, [153 , LCD will display: Emu Nurser (Flickering) Selection donate wf Ere Setting erm Ed, HE Current values 2. Press [MENU again, LCD display: 1% B-ETC a 304, HZ 3. Rotate the channel knob CENT] to select the desired receiving CSS code (OFF, 67 0Hz . 284.1Hg) 4.
Note: The CROSS and DOS function can not be activated al the mass time, If vou activate the STANCES first, and then open the DCS function, the CSS function will be closed Ee aly. Setting audio tones (PRO} 1. Press [MENU and then rotate the channel knob TENT to menu ne. £193 , LOD will display: Man Number (Nickering) Selection indicator pro emt: Sling Hera OFF —— Current value 2. Press [MENU again, LCD display: ® FPR pe OFF 3. Rotate the channel knob [ENC] to select desired audio tones.
Setting Frequency/ChannslMessage display mode {CH-MD F) 1. Press [MENU and then relate the channel knob {ENC to menu no £233 , LCD will display: Peru Number (Flickering) 23 Selection indicator wt ~~ UH-MD F wot Calling Hem FREE + Resurgent naive 2. Press [MENU again, LCD display: 25 CH-ND F i FREER 3. Rotate the channel knob [ENG] to select display mode.
Setting Offset frequency Direction (OFFSET-D) 4. Press [MENU and then rotate the channel knob [ENCY to menu ne. £271, LCD will display: Peru Number (Flickering) Belling Hera Selection indicator E BET . OF Currant value 2. Press [MENU again, LCD display: v SF-B OFF 3. Rotate the channel knob [ENCY 10 select direction of offset frequency. (OFF, 4, 4.
ai 4. Press [MENU again, LCD display: Es ee Refers to successful storage 5. Press [MENU] to store same transmitting frequency. LCD display: 38 MEN-CH I 6. Press [MENU] fo confirm and store the current transmitting channel and continue other menu setting, or press {EXIT to cancel the current chatting values and sdf the menu mode at the mass time. Setting Transmitting Channel (MEN-CH) 1.
22 RESET ee MFC 3. Rotate the channel! knob ENC to select the desired operation. (FOWL Resume to factory default; ALL= Delete all storage.) Note: Ono you operate "ALL", all the stored channel and function will be deleted. 4. Press [MENU again, LCD display: 32 RESET ~~ SURE? 5.
MISCELLANY LACQUERS FUNCTION REMAINING BATTERY CAPACITY Before you operate the transceiver outside using a battery pack, It is important to know how long the battery pack will last. The battery remaining Indicator shows the remaining capacity. ws igh battery power <# Medium battery power ox Low battery power on Recharge or replace the batteries, WIRED CLONE The steps to active wired clone: 1. Tum on the power of the vice radio, and then connect the two radios with cloning cable. 2.
MISCELLANEOUS FUNCTION SOME SPECIAL KEYS OPERATING INSTRUCTIONS sr LAB] kay, used for switching A/ B frequency band; or worked as “AY code under the MDT sidling. . MINUTEMEN key, used for entering inlet menu operation or as [FUNGI key; or worked as code “B” under MDT dialing. LAXITY key, used for exiling meow operation or canceling the current operation; of worked as code © In the MDT dialing. EPEE} key, used as user-defined operation; or worked as ode “0 under the MDT dialing. .