QP-650V1 USER MANUAL Quantun Electronics, LLC Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules.
User Safety, Training, and General Information READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE USING YOUR QUANTUN PORTABLE TWO-WAY RADIO. Compliance with RF Energy Exposure Standards Your Quantun two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy.
Operational Instructions and Training Guidelines To ensure optimal performance and compliance with the occupational/controlled environment RF energy exposure limits in the above standards and guidelines, users should transmit no more than 50% of the time and always adhere to the following procedures: Transmit and Receive To transmit (talk), push the Push-To-Talk (PTT) button; to receive, release the PTT button.
FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
z Do not modify or adjust this transceiver without permission. z Do not expose the transceiver to direct sunlight over a long time nor place it close to heating source. z Do not place the transceiver in excessively dusty, humid areas, or on unstable surfaces. Safety: It is important that the operator is aware of and understands hazards common to the operation of any transceiver. Care and Cleaning z Do not place the repeater in a dusty or dirty environment.
NOTICES TO THE USER Government law prohibits the operation of unlicensed radio transmitters. Illegal operation is punishable by fine or imprisonment Of both. To avoid problem caused by electromagnetic interference and electromagnetic compatibility, please turn off the transceiver at the sites where you are required, such as hospital, airplane etc. THANK YOU We are grateful for you choice of Quantun transceiver. This Professional two-way radio incorporates the advanced technology and craft.
CONTENTS Unpacking and Checking Equipment Supplied Accessories Battery Pack information Charging Notices Charging Instructions Care and cleaning Accessories Installation Installing and Removing the Battery Pack Installing and Removing the Antenna Installing and Removing the Belt Clip Installing the Optional Mic.
Unpacking and Checking Equipment Battery Information Charging Notice Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, please contact Sureave dealers immediately. Supplied Accessories ITEM The battery is not charged at the factory, which can not reach its full capacity for the first charging.
Care and Cleaning Charging Instruction Insert the battery or the radio with the battery into the charger, and make sure than the battery connectors are in contact with the charging terminals.The LED indicators glows red during charging and green when the battery is fully charged.
Accessory lnstallation Attaching the antenna Attaching the Battey 1. Align the threaded end of the antenna with the Radio’s antenna connector. 2. Turn the antenna clockswise to tighten.(See Figure 3) 1.Turn off the radio. 2.Insert the tabs at the bottom of the battery intothe slots at the bottom of the radio chassis. 3.Press the top of the battery towards the radio until a click is heard.(See Figure 1) Removing the antenna 1.Turn the antenna counterclockwise until you can remove it.
Radio Overview Removing the Belt Clip 1.Press the belt clip tab upwards until it releases. 2.Slide the belt clip upwards to remove it.(See Figure 5) Note: remove the battery pack prior to removing the belt clip. Figure 5 Attaching External Earphone(Optional) 1.Remove the cover of earphone jack. 2.Rotate the cover until earphone jack comes into view. Insert the earphone plug into the jack.
(1) Antenna Used to transmit/receive signals. (2) LED Indicator The radio LED glows red during transmission and green during reception; The LED flashes red when battery voltage is low. (3) Channel Selector Knob (8) Speaker Used to output sounds. (9) External Jack(for external earphone or radio programming) Rotate the jack cover and insert accessory plug or insert programming cable into the jack to program the radio via programming software.
Basic Operation 1. Turn on the radio: Turn the Power/Volume Control Knob clockwise until a "click" is heard. 2. Adjust the volume:Turn the Power/Volume Control Knob to adjust the volume.When function key is programmed with monitor feature, turn the knobwhile holding down the function key to adjust thevolume to a comfortable level. 3. Select a Channel: Rotate Channel Selector knob to select your desired channel. 4. Transmit: Hold down the [PTT] key ,speak into the microphone with normal voice.
Monitor This feature is enabled/disabled by your dealer.In receive mode, press the preprogrammed MONI key to monitor activities on the current channel .This operation is especially useful for adjusting volume level or receiving a weak signal.The LED indicator glows green in monitor mode. Busy Channel Lockout If the Busy Channel Lockout feature is enabled by your dealer, it will prevent you from talking on a channel that is already in use.
Battery Save The Battery Save feature is automatically activated once no activity on the channel and no operation performed for 10 seconds, for extended operation time. When a signal is received or an operation is performed, the Battery Save feature is automatically deactivated. Low battery Alert When the battery voltage goes below a preset value, the LED indicator Will flash red and the alert tone sound and then the radio stops transmitting.
Troubleshooting Guide Trouble No power Solution Battery is low. Recharge or replace the battery. The battery may not be properly installed. Remove the battery and attach it again. Power doesn't last long even if fully charged Battery has lost its capacity, replace it with a new one. Can't talk to or hear group members Make sure you are using the same frequency, same CTCSS/DCS and same 2-Tone as your group members. Your group members may be out of the communication range.
