Quanta Microsystems Inc.
Quanta Microsystems, Inc. Subject: Doc No. ZM10 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Rev: Page: Reason for Release： Revision Effective Date Author 0.1 03/28/2008 Samuel Wang Description of Changes Modified from OP_ZM100-1 QMI PROPERTY & CONFIDENTIAL! 2 0.
Quanta Microsystems, Inc. Subject: Doc No. 1. ZM101 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Rev: Page: 0.2 3 of 10 Adaptor board connection and setup Power IN (+2.7~+3.3Vdc) USB plug in: ― J_USB should be selected as USB PWR IN mode ― USB +5V Æ LDOÆPower in RCA Jack plug in: ― J_DC should be 2-3 pin short. ― Use a +4~7V(inner) DC adaptor plug in CON_RCAÆ LDOÆPower in Pin header plug in: ― Use other power source(such as power supply) ― Supply +2.7~+3.
Quanta Microsystems, Inc. Subject: Doc No. ZM10 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Rev: Page: 0.2 4 of 10 Adaptor board placement and jumper selection J_CURRENT: For DC current measurement use; Default is short by Jumper. J_DC: DC input selection ― 1-2 Short by Jumper : Use USB +5VÆLDOÆ3.3V ― 2-3 Short by Jumper : Use RCA Jack ― Open : Use J_3V pin header CN USB: Insert USB A-type cable connect to USB host to provide +5Vdc.
Quanta Microsystems, Inc. Subject: Doc No. ZM101 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Rev: Page: 0.2 5 of 10 FW download Connect 4pin connector to adaptor and use USB multi-link or programmer download, 2X3 pin header pin1 are marked in square. Open OS hyper terminal as a com port used UART connection Use a D-SUB9 cable connects to PC com port Open OS hyper terminal as a com port used Set properties as following Fig 1.
Quanta Microsystems, Inc. Subject: Doc No. ZM101 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Fig 1.2 Hyper terminal Properties settings QMI PROPERTY & CONFIDENTIAL! 6 Rev: Page: 0.
Quanta Microsystems, Inc. Subject: Doc No. ZM101 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Rev: Page: 0.2 7 of 10 Fig 1.3 ASCII setup After finished above item, connect DUT and adaptor board by 6pin wire connection.
Quanta Microsystems, Inc. Subject: Doc No. 2. ZM101 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 RF test mode application Channel selection Set channel ― Select character “1,2,3….,f,g to set channel 1~16 QMI PROPERTY & CONFIDENTIAL! 8 Rev: Page: 0.
Quanta Microsystems, Inc. Subject: Doc No. ZM101 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Set output power ― Default power: -0.66dBm (select character “n”) QMI PROPERTY & CONFIDENTIAL! 9 Rev: Page: 0.
Quanta Microsystems, Inc. Subject: Doc No. ZM101 operation manual-RF mode Revised Date: OP_ZM10X-1 2008/03/28 Rev: Page: 0.2 10 of 10 Set operation mode ― Select character “v,w,x…r,s” for operation mode After you finished testing, you can select character “t” to go back to main manual. If you can not go back to main manual (ex. DUT on sleep mode); it shall be power off then power on DUT to go back to main manual.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:T5U-ZM101”.
