Installation Instructions

Quamtum Connect 1 Instructions
V1.0
Thank you for choosing our 5G wireless data terminal products. In
order to make you better use the data terminal, please read this
manual carefully and keep it for backup after reading it.
Our company reserves the right to modify the technical
parameters and specifications of this manual. Any misprints and
discrepancies with the latest information will be promptly
corrected. All changes are made without prior notice and the
company reserves the right of final interpretation.
Quamtum Connect 1 is a high-performance 5G indoor data
terminal that supports NR(SA&NSA) and LTE, converts cellular
network data into Wi-Fi and wired network port data, supports 4
gigabit LAN ports, and supports 2.4G+5G dual-band Wi-Fi
hotspot (AP). It is suitable for home or business scenarios that
require rapid deployment of communication networks, Wi-Fi
hotspots.
I. Main technical indicators of products
● Operating temperature : 0℃~40℃
● Relative humidity :5%~95%
● Power: input AC 100 V~240 V,50Hz~60 Hz
Output DC 12V/1.5A
● Size:117mm*117mm*188.8mm
● Weight: 580g
● Uplink and downlink rate: 5G DL 2Gbps, UL 1Gbps
(Theoretical value and actual rate are subject to operator
configuration)
II. Installation instructions
1） Take out the wireless data terminal and install the USIM card
into the slot according to the direction marked on the data
terminal. When the "click" sound is heard, the USIM card is
installed in place.
2） Use RJ45 standard network cable to connect the LAN port
and computer of the data terminal.
3） Connect the external power outlet and data terminal with the
power adapter, press the switch and turn on the data terminal
automatically. About 1~2 minutes later, the data terminal
completes initialization.
4） Place the data terminal in a flat place.
Attention : 1. Do not install USIM card live.
2. When take the USIM card, do not touch the metal
contact surface to avoid electrostatic damage to the
card.
III. About the data terminals
This data terminal can work under 4G (LTE)/5G NR network, and
can connect the data terminal to the Internet through Wi-Fi or
network port.
3.1 Appearance Interface Introduction
Figure 1 Interface
Interface Interface uses Remarks
POWER Power switch
Press to turn on the power and
then press to turn off the
power
Power jack
Power interface,
connected to the
particular power
adapter.
Be sure to use the particular
power adapter, using another
adapter may cause damage to
the device or other hazards.
RESET
Reset key, long press 7
seconds to restore
factory settings
Restore factory settings will
clear all user settings
parameters, please be careful.
LAN1~LAN4
Ethernet interface, used
to connect computers
and other devices.
The LED flashes when
connected.
SIM
USIM card interface,
please insert the USIM
Do not unplug the USIM card
when power on.
card correctly in the
identification direction.
3.2 Indicator
Figure 2 Indicator
Indicator State Description
Wi-Fi OFF Wi-Fi not open
Blue Wi-Fi open
SIGNAL
OFF
No signal (signal values can
also be viewed through the
data terminal configuration
page)
Red light flashing SIM card not identified
Red Poor signal quality
Yellow Normal signal quality
Green Good signal quality
POWER
OFF
Foreign power exception,
data terminal closed
On
Normal external power, data
terminal open
4G OFF 4G unregistered network
Blue 4G Registered Network
5G OFF 5G unregistered network
Blue 5G Registered Network
WPS key: press the button for 1 to 3 seconds to release, the
WIFI light flashes quickly, and the 5G WIFI WPS function is
enabled. Press and hold for more than 6 seconds to release, the
WIFI light flashes slowly, and the 2.4G WIFI WPS function is
enabled. Devices that support WPS function (such as mobile
phones) can automatically connect when entering WPS mode,
and WPS function will be turned off automatically after 2
minutes of turning on.
IV. Access to the Internet
The data terminal supports connecting the computer RJ45 a
standard network cable or WLAN wireless without any driver.
Support Windows XP、Windows 7、Windows 8、MAC OS、Linux、
Android and other operating systems.
4.1 Data terminal readiness
Before accessing the internet, please check the following options:
●USIM card valid and correctly inserted into data terminal
●Power indicator light
●Signal indicator light, preferably green
●4G or 5G indicator lights, blue
4.2 Connecting Computers
The data terminal and computer can be connected by RJ45
standard network cable or by Wi-Fi. Wi-Fi connection, SSID and
Wi-Fi password information please check the sticker at the bottom
of the data terminal. The SSID and Wi-Fi passwords of each data
terminal are unique. Either way to connect, set the computer
address acquisition mode to "automatically get the IP address ".
4.3 Access data terminal
After the computer gets the IP address, enter "192.168.0.1" in the
browser and enter the user name and password to access the data
terminal configuration page. The default user name of the data
terminal is "admin" password is "admin".
The login data terminal configuration page recommends using
any of the following browsers:
●IE 7.0 or above
●Firefox 3.0 or above
●Safari 4.0 or above
●Opera 10.0 or above
●Chrome 10.0 or above
V. Configuration of data terminals
When configuring the data terminal, make sure the data terminal
works properly and the computer is connected to the data
terminal. Then log in to the data terminal configuration page for
configuration. Data terminal configuration page parameters
should be carefully configured according to operator
recommendations, improper configuration may lead to unable to
access the Internet. Press "reset" key to restore factory settings.
Primar
y
Secondary
menu
Operational instructions